Grizzly C1393-96 User manual

-1-
INSTRUCTIONS FOR
C1393-96, C1651
STILE AND RAIL SETS
• Failure to follow these guidelines will result in
seriouspersonalinjury.
• ALWAYSWEARANSIAPPROVEDEYEANDEAR
PROTECTIONwhenusingthisbit.
• Alwaysusearoutertablewhenusingthesebits,
NEVERattempttouseahand-heldrouter.
• Neverfeedlumberwiththerotationofthecutter.
• Follow the safety guidelines set forth by the
manufactureroftherouterandroutertable.
These router bits have sharp edges. Use care
whileremovingthewaxyprotectivecoating.Never
turnontherouterwiththeprotectivecoatingstill
onthebit.
• Unplug router before installing or adjusting
cutter.
• Keep all guards and anti-kickback devices in
place.
• Double check bit to insure it is tight and
secureinrouter.
• Alwaysinspectlumberandotherwoodmaterials
for cracks, knots, or other imperfections that
couldcauselumbertokickorshatterwhilemill-
ing.
Togetthemostfromthesecarbide-tippedstile
andrailbits:
1. For maximum efficiency, secure each bit in a
routerandplanallofyourcutstominimizebit
changes(orkeepeachbit inaseparate rout-
er).
2. Adjusttherouterand
bit in your router
table, so the
bit offers a
fullprofilein
addition to
about1⁄8"of
indentation
on the front
edge of the
material. You will be milling your
material back side up, so the indentation
willbeattablelevel.(Seetheillustrationtothe
right.)
3. Oncethebitisproperlyadjustedandtightened
inplace,usealengthofsurplusmaterialthatis
the same thickness as your workpiece  for a
test cut. If you are satisfied with your results,
continuewithyourprojectmaterial.engagement
toensureanequaldepthofcut.
FENCE
StileandRailSet
Deluxecarbide-tippedStileandRailbitsinanum-
berofclassicandcontemporarystyles,offerexcel-
lent  performance for the serious woodworker or
cabinetmaker working with stile and rail materials,
rangingfrom3⁄4"to7⁄8"widths.Two-piecerouterbit
setsenableyoutoincreaseproductivitybykeeping
tworouterspre-adjusted.
INTRODUCTION
Although these bits can be used hand-held with
properjigsandfixtures,werecommendusingthem
inaroutertable,suchastheRebel®RouterTableby
WoodstockInternational.

-2-
The process for completing your rail end cuts is
roughly the same as those for your stile and rail
cuts.Themainconcernisensuringthattheamount
ofrevealatthefrontedgeofyourrailmatchesthe
cutsmadeinyourstiles.
Tocompleteyourendrailcuts:
1. Adjustyourrouterand
bit,asdescribed
earlier,
and
make
atest
cut
with
thesur-
plusmate-
rial.
2. Join the test cut with your  previous cuts and
checkthejointtodetermineflushness.
3. Re-adjustandre-testuntilyouaresatisfiedwith
yourresults.
4. Whensatisfiedwiththeresultstightentherouter
andcutyourprojectmaterial.
A ball bearing is supplied with these router bits
whichallowtheuseoftemplatesforcurvedwork
asseentotheright.
Usingatemplate:
1. Thetem-
plate
should
bethe
same
sizeas
the
expected
finished
panel.
2. The curved portion of the workpiece should
be rough cut so that no more than 1⁄8" pro-
trudesbeyondthetemplate.
3. Thefenceandmitermustberemovedwhen
usingatemplate.Astartingpinorblockmust
beinstalledasshowninFigure2.
Always disconnect power to
themachinewhensettingup
or making adjustments.
Failure to do this may result
inseriouspersonalinjury.
FENCE
Figure2.Startblockfortemplatecutting.