Grizzly G0758Z User manual

COPYRIGHT © JUNE, 2017 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MANUFACTURED SINCE 02/17) #KB18652 PRINTED IN CHINA
Model G0758Z is an upgraded version of Model
G0758 with an included X-/Y-/Z-Axis DRO.
NOTE: The column, table, and saddle on this
model have been specially machined to mount the
DRO scales. Thus, the DRO components includ-
ed with these models cannot be easily retrofitted
onto Model G0758.
: To reduce the risk of serious
injury, you MUST read and understand this
insert—and the entire Model G0758 manual—
BEFORE assembling, installing, or operating
this machine!
If you have any further questions about this
manual insert or the differences between the
Model G0758 and the Model G0758Z, contact
our Technical Support at [phone] or email
[email protected].
MODEL G0758Z
MILL/DRILL W/DRO
MANUAL INSERT

-2- Model G0758Z (Mfd. Since 02/17)
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 P0758Z001 Z-AXIS SLIDE 407 P0758Z407 CAP SCREW M4-.7 X 8
48 P0758Z048 COLUMN 408 P0758Z408 Y-AXIS DRO SENSOR
54 P0758Z054 TABLE 409 P0758Z409 Y-AXIS SENSOR MOUNTING BLOCK
68 P0758Z068 SADDLE 410 P0758Z410 Y-AXIS METALLIC STRIP 10 X 150MM
76 P0758Z076 BASE 411 P0758Z411 Z-AXIS DRO SENSOR
302 P0758Z302 MODEL NUMBER LABEL 412 P0758Z412 Z-AXIS SENSOR MOUNTING BLOCK
308 P0758Z308 MACHINE ID LABEL 413 P0758Z413 Z-AXIS METALLIC STRIP 10 X 390MM
309 P0758Z309 CONTROL PANEL LABEL 414 P0758Z414 CAP SCREW M3-.5 X 16
401 P0758Z401 DRO DISPLAY UNIT 415 P0758Z415 CAP SCREW M4-.7 X 16
402 P0758Z402 X-AXIS DRO SENSOR 416 P0758Z416 STEEL SLEEVE 5 X 18 X 33L
403 P0758Z403 X-AXIS SENSOR MOUNTING BRACKET 417 P0758Z417 CAP SCREW M5-.8 X 50
404 P0758Z404 X-AXIS METALLIC STRIP 10 X 480MM 418 P0758Z418 CAP SCREW M4-.7 X 8
405 P0758Z405 ALUM BRACKET 30 X 480 419 P0758Z419 DRO POWER CORD 2W 18G 72" 1-15P
406 P0758Z406 FLAT WASHER 4MM
G0758Z Unique Parts
1
2
10
4
5
6
7
8
9
10
11
12
13
14
15
18
19
417
19
21
22
23
24
48
54
68
76
408
414
415
402
414
418
401
406
403
416
404
405
409
406
407
410
413
412 411 414
415
22
19
416
zero
zero
zero
in
mm
mm
inch
X
Y
Z
419 302
G0758Z
1000 RPM50 RPM
100 RPM 2000 RPM
– L –
– H –
309
Specifications
Model G0758Z
Motor: 600W (3/4 HP), 110V, 10A, 60 Hz
Max. Dist. Spindle to Column: 6-5/8"
Max. Dist. Spindle to Table: 8-3/4"
Spindle Taper: R-8
Longitudinal Table Travel: 13-1/8"
Cross Table Travel: 4-1/2"
Drilling Capacity Cast Iron: 5/8"
Drilling Capacity Steel: 1/2"
End Mill Capacity: 5/8"
Face Mill Capacity: 2"
Weight: 161 lbs.
Mfd. for Grizzly in China
Date Serial Number
308

Model G0758Z (Mfd. Since 02/17) -3-
DRO Components
The X-axis sensor and scale are attached to the
table. The Y-axis scale is attached to the saddle,
and the Y-axis sensor is attached to the base.
The Z-axis sensor and scale are attached to the
column. Shielded cables run from each sensor
to plugs on the back of the DRO (see Figure 2).
The DRO connects to a 110V power supply with
a dedicated power cord using a NEMA 1-15 plug.
Figure 1. DRO magnetically mounted to mill
headstock.
Model G0758Z features a magnetically mounted
DRO (see Figure 1) for X-axis (table), Y-axis
(saddle), and Z-axis (column) travel.
Note: When placing the DRO, locate all cables so
they do not interfere with machine operation and
cannot be pinched by moving components.
Digital Readout
A. DRO displays current position of X-axis,
Y-axis, and Z-axis in hundredths of a millime-
ter or thousandths of an inch.
B. "X" value displays total X-axis travel from
zero along table.
C. "Y" value displays total Y-axis travel from
zero along saddle.
D. "Z" value displays total Z-axis travel from
zero along column.
E. In/MM button allows users to toggle
measurement display in either inches or
millimeters.
F. ZERO buttons reset values at any point along
the axis to 0.00.
G. Green light indicates inches or millimeters.
H. Magnetic mount.
Using the DRO
DRO
(Viewed from behind)
110 VAC
1-15 Plug
NEUTRAL
HOT
Z-Axis Sensor
Y-Axis Sensor
Z-Axis Port
Y-Axis Port
Power Cord
Port
POWER
X-Axis Port
X-Axis Sensor
CXM-3
Figure 2. G0758Z DRO wiring.
Figure 3. DRO controls and display.
B
D
G
AH
E
C F
Figure 4. DRO cable connections (rear).
Z-Axis
Port
ON/OFF
Switch
DRO Power
Cord
Y-Axis
Port
X-Axis
Port