GRS GraverHone VS User manual
English en-1
Important notes are highlighted in yellow or marked in red.
GraverHone VS
OPERATION AND MAINTENANCE MANUAL
#003-598-EU
ORIGINAL INSTRUCTIONS FOR EUROPE
Contents
Important Notice For Operators ...................... 2
Required Equipment ............................... 2
Introduction...................................... 3
Setup ........................................... 3
Operation........................................ 3
Maintenance ..................................... 4
Service & Repair .................................. 4
Warranty ........................................ 4
Read this manual entirely before connecting to power source.
Damage not covered by the warranty may result from not following the instructions and maintenance in this manual.
THIS PRODUCT IS APPROVED FOR SALE IN THE EU
This product and its documentation are created in compliance with
international laws and are approved for export outside the United States of America.
See Declaration of Conformity for details.
en-2 English
IMPORTANT NOTICE FOR OPERATORS
No user serviceable parts inside. Do not remove any outer
surfaces. Do not modify this equipment or remove warning labels.
Modifications can increase risks to the operator. Do not use this
equipment if it is damaged.
Always wear sucient eye protection. Take steps to avoid dust
inhalation by wearing appropriate respiratory protection.
Do not lift or transport by grasping the drive plate or spindle. Allow
the drive plate and sharpening wheel to come to a complete stop
before:
• grasping the drive plate and / or wheel
• changing the wheel
• grasping or attempting to remove the wheel lock
Plug into grounded outlets only. Do not use adapters that bypass the
ground plug.
Do not apply excessive or forceful pressure to a tool while using this
unit. This action may result in damage to the tool, the unit and its
components, and / or the operator.
Tools may become hot while operating this unit as intended. Protect
skin and surfaces from burns or damage.
Tools can be extremely sharp after this unit is used as intended.
Protect skin and surfaces from punctures, cuts, or damage.
Do not attempt to operate this unit in any position other than upright
as shown with the Front View in FIG. 1 on page 3.
The proper use of this equipment does not generate noise above
70dB(A).
FOR URGENT SITUATIONS, STOP THE UNIT IMMEDIATELY BY:
• Powering o the unit with the power switch button
• Setting the reversing rocker switch to the center “o” position
• Disconnect the 24-volt power converter from the back of the unit
• Disconnect the 24-volt power converter from the electrical power source
• Included 24-volt power converter connected to a
properly grounded electrical power outlet.
USE ONLY THE SUPPLIED 24-VOLT POWER CONVERTER. The included
power converter may be connected to any properly grounded single-
phase source of AC power within a voltage range of 100 to 240 V, 50
or 60 Hz. The power converter must be used with a suitable grounded
electrical system. Using it with an ungrounded system could expose
the equipment to electrical damage. Do not use older generation power
converters. If a replacement is needed, contact GRS or an authorized
GRS dealer.
• A sturdy surface with adequate lighting.
Make use of a heavy workbench or suitable solid furniture to support
this equipment, workpiece, and any additional equipment and supplies.
Adequate lighting allows clear sight, and may help prevent accidents
and reduce fatigue.
• Respiratory protection appropriate for the
material being ground.
The dust created while sharpening some tool materials may present a
health risk.
• Eye protection.
REQUIRED EQUIPMENT
Read this manual entirely before connecting to power source.
Damage not covered by the warranty may result from not following the instructions and maintenance in this manual.
English en-3
12mm
POWER: 24 VDC / 3.75 A (MAX)
GraverHone VS
0000000000000
A
B
C
D
Overview
FIG. 1
A. Power on/off button
B. Reverse rotation switch position
C. Forward roation switch position
D. Rotations Per Minute (RPM) dial
E. 24-volt power receptacle
F. Spindle
G. Drive plate (#111-522)
H. Metal washer (#024-417)
I. Bolt (#111-515)
J. Quick Lock Knob & Spring
(Wheel Lock) (#111-521)
Attach Drive Plate
FIG. 2
E
F
I
F
G
Front View
Back View Top View (with Drive Plate)
E
INTRODUCTION
The GraverHone VS is designed to be
used for the purpose of sharpening and
polishing tools.
SETUP
ATTACH DRIVE PLATE & WHEEL (FIG. 2)
Place drive plate (G) on spindle (F). Place metal
washer (H) in inset at center of drive plate.
Thread bolt (I) into center of drive plate and
secure on spindle. Tighten with 12mm wrench.
Place wheel on drive plate. Align and place
quick lock knob and spring (J) assembly over
bolt. Push down and twist into locking position.
CONNECT ELECTRICAL POWER (FIG. 3)
Insert the converter cord into receptacle on
unit (FIG 3.1). Connect the electrical power
cord into the 24-volt power converter (FIG 3.2).
Connect the 2-prong power cord into a properly
grounded power outlet.
OPERATION
Press power on/o button to power unit on.
(FIG. 1 A). Unit must not be in operation while
installing or removing sharpening wheel. If not
installed, attach wheel securely on drive plate
(FIG. 1 G). Position RPM dial to desired RPM
setting (FIG. 1 D).
Set rotation switch to clockwise (FIG. 1 C) or
counter-clockwise (FIG. 1 B) as desired. When
finished, set rotation switch to center “o”
position. When finished, press power on/o
button to power unit o. (FIG. 1 A).
I
J
J
G
H
Connect Electrical Power
FIG. 3
G
I
H
#024-411 #022-994
G
2.1 2.2 2.4
2.3 2.5
3.1 3.2
en-4 English
WARRANTY
Each GraverHone VS carries a full 2-year warranty
covering parts and labor. Contact GRS or an
authorized GRS dealer before returning any
equipment.
SERVICE & REPAIR
Please call GRS or an authorized GRS dealer for
service and repair. Unauthorized servicing will void
the 2-year warranty. This unit is not serviceable by the
operator and must be sent in to GRS or an authorized
GRS dealer for repair.
MAINTENANCE
To maintain this unit, keep all surfaces free of dust and
debris with regular cleaning using a damp cloth. Take
appropriate measures to avoid inhaling dust while
cleaning.
For guidance with operation or maintenance, please contact GRS
or an authorized GRS dealer. To send a request for assistance via
https://www.grs.com/customer-service/
English See included disc for original
manual in this language.
Products made in USA. © 2017 Glendo LLC. All rights reserved.
LIT-442-EU-en
Last Update: 2017-08-16
Glendo LLC
900 Overlander Road
Emporia, KS 66801 USA
Phone: +1-620-343-1084
Fax: +1-620-343-9640
E-mail: [email protected]
grs.com
READ THIS MANUAL ENTIRELY
BEFORE CONNECTING TO POWER.
Damage not covered by the warranty may result from not
following the instructions and maintenance in this manual.
