Grundig GD-HW-BPBB0550G User manual

0

1
Quick Guide
About this guide
The guide includes instructions for using and managing the product.
Pictures, charts, images and all other information hereinafter are for
description and explanation only. The information contained in the
guide is subject to change, without notice, due to firmware updates or
other reasons.
Please find the latest version at WWW.GRUNDIG-SECURITY.COM
Limitation of Liability / Legal Disclaimer
Abetechs GmbH (Grundig Security) undertakes all reasonable efforts
to verify the integrity and correctness of the contents in this document,
but no formal guarantee shall be provided. Use of this document and
the subsequent results shall be entirely on the user’s own
responsibility. Abetechs GmbH (Grundig Security) reserves the right to
change the contents of this document without prior notice. Design and
specifications are subject to change without prior notice.
The product described herein, with its hardware, software and
documentation is provided “as is”, without any warranty, expressed or
implies, including without limitation, merchantability, satisfactory
quality, fitness for a particular purpose, and non-infringement of a
third party.
In no event will our company and its employees or agents be liable to
you for any special, consequential, incidental, or indirect damages,
including among others, damages for loss of business profits, business
interruption, or loss of data or documentation, in connection with the
UG-GD-HW-BPBB0550G-2020-04-09-V4-EN ©ABETECHS GMBH, DÜSSELDORF, GERMANY

2
use of this product, even if our company has been advised of the
possibility of such damages.
Regarding to products with internet access, the use of the product
shall be wholly at your own risks. Our company shall not take any
responsibilities for abnormal operation, privacy leakage or other
damages resulting from cyber-attack, hacker attack, virus inspection,
or other internet security risks; however our company will provide
timely technical support if required. Surveillance laws vary by
jurisdiction before using this product in order to ensure that your use
conforms to the applicable law. Our company shall not be liable in the
event that this product is used with illegitimate purposes.
In the event of any conflicts between this manual and the applicable
law, the later prevails.
Trademark
Each of trademarks herein is registered. The name of this product and
other trademarks mentioned in this manual are the registered
trademark of their respective company.
Copyright of this document is reserved. This document shall not be
reproduced, distributed or changed, partially or wholly, without
formal authorization.

3
Safety and Installation Instructions
Introduction
Please read these instructions carefully and keep them for future
reference. You must heed all the warnings and cautions as well as
follow all the safety and installation instructions.
The appearance of the products, functions and firmware or software
upgrade may differ from this manual.
GRUNDIG reserves the right to perform needed changes without prior
notice.
Safety Instructions
Make sure that you only use the power adapter that is specified in the
specifications sheet of the product. If you use any other adapter or
connect the power supply incorrectly, this may cause explosion, fire,
electric shocks or damage the product. Do not connect several devices
to one power adapter as this may cause an adapter overload and can
lead to over-heating and fire. Make sure that the plug of the power
adapter is firmly connected to the power socket.
Do not place containers with liquids on the product. Do not place
conducting items like tools, screws, coins or other metal items on the
product. These may fall from the product or can cause fire or electric
shocks or other physical injuries.
Do not push or insert any sharp items or any objects into the device as
this may cause damage to the product, fire, electric shocks and/or
physical injuries.

4
Do not block any ventilation openings, if there are any. Ensure that the
product is well ventilated to prevent any over-heating.
Do not subject the device to physical shock or drop the product.
If the product uses batteries, please use a battery type that is
recommended by the manufacturer. Improper use or replacement of
the battery may result in the hazard of explosion.
Do not use any accessories that are not recommended by GRUNDIG.
Do not modify the product in any way.
If the product starts to smell or smoke comes out of the device,
immediately stop using the product and disconnect it from the power
supply to prevent fire or electric shocks. Then contact your dealer or
the nearest service center.
If the product does not work correctly, contact your dealer or nearest
service center. Never open, disassemble or alter the product yourself.
GRUNDIG cannot accept any liability or responsibility for problems
caused by attempted and unauthorized repair and maintenance.
Installation Instructions
It is necessary to fix the device firmly if the product is installed on a
wall or ceiling. Do not install the product on surfaces or in places that
are vibrating. Do not install the product near radiation sources.
Do not install the product near heat sources, like radiators or other
equipment that produces some heat. If the product is not classified by
any IP class, do not install the product in very cold or hot temperatures
(please refer to the working temperature specified in the specification
sheet of the product), dusty, dirty or damp environment.

5
If the product is classified by any IP class, never touch the product
cover directly with your fingers, because the acidic sweat of the fingers
may damage the surface coating of the product cover. To clean the
inside and outside of the product cover, use a soft and dry cloth. In any
case, do not use alkaline detergents. The correct configuration of all
passwords and other security settings is the sole responsibility of the
installer and/or end-user (this applies especially to IP Cameras and
Recorders).

6
Table of Contents
1 Function .......................................................................................... 7
2 Appearance and Display Introduction ............................................. 8
3 Technical Data ................................................................................. 9
4 General.......................................................................................... 10
4.1 Mounting ...................................................................... 10
4.2 Operation ...................................................................... 10
4.3 Maintenance ................................................................. 11

7
1 Function
The product is specially designed for calibrating body temperature
detection thermal device and thermal inspection device in various
sizes.
Excellent temperature uniformity, accuracy, and stability of
calibration.
Adopts intelligent temperature controller and has high temperature
control accuracy.

8
2 Appearance and Display Introduction
Device Appearance
Measuring
Temperature
（PV）
Setting
Temperature
(SV)
Control
Panel
Temperature Controller

9
3 Technical Data
Parameter Value
Temperature Range Adjustable: environment temperature
+5 °C (9 °F), up to 50°C (122 °F)
Effective Radiating Area Ф 70 mm (2.76”)
Temperature
Resolution
0.1 °C (0.18 °F)
Temperature Accuracy ± 0.1 °C (0.18 °F)
Temperature Stability ± 0.1 °C/h
Effective Emissivity 0.97 ± 0.02
Power Consumption 20 W
Environment
Temperature
0 °C to 40°C (32 °F to 104 °F)
Weight 1.85 Kg (4.08 lb)
Dimension 120 mm × 176.6 mm × 119.6 mm
(4.72” × 6.95” × 4.71”)
Power 100 VAC to 240 VAC
Mounting Mounting on a plane desk or a tripod
with 1/4-20UNC Interface or a ceiling
mount bracket with 1/4-20UNC
Interface

10
4 General
4.1 Mounting
Check the power supply. The working voltage should be 100 VAC-240
VAC, 35 W.
Check if the desk is horizontal.
Mount the device on the desk or a tripod in front of the thermal
camera firmly. The distance to the camera is depending on the
camera model. Make sure that the front of black body can show in
the live view of thermal camera completely, and outside the
temperature measurement area.
Switch on the device, and the power indicator is on. The factory
default setting temperature is 40 °C.
4.2 Operation
Connect the black body with a 10 A socket via the power cable.
Switch on the device, and the power indicator is on. The factory
default setting temperature is 40 °C.
Wait for 30 minutes after switching on device. You can calibrate the
thermal camera when the temperature is stable at 40 °C.
Switch off the black body and store it after use.

11
4.3 Maintenance
The black body should be managed and maintained by professional
person and maintenance and usage should be recorded.
DO NOT use the device in an environment with oil or chemical air.
To ensure the temperature accuracy, place the device firmly in the
environment with stable temperature. The recommended using
environment temperature is 10 °C to 25 °C (50 °F to 77 °F)
Power off the device before mounting or removing it.
Clean the surface of device with a neutral detergent. Clean the dust
on the black body with a soft brush.
Store the device in the packing box after use to prevent dust. Make
sure the environment temperature is suitable.
DO NOT dismantle the device without authorization. Contact the
professional specialist for repairing.
To ensure the temperature accuracy, it is recommended to calibrate
the black body once a year. Please send the device to qualified
calibration institute.

UG-GD-HW-BPBB0550G-2020-04-09-V4-EN ©ABETECHS GMBH, DÜSSELDORF, GERMANY
grundig-security.com