GST DI-9305E User manual

30310467 Issue 1.04
Features
Cable checking for output cables input audio
cables or 24V input cables.
Occupying one address. It can be modified in
filed.
Output port utilizes AD sampling technology for
precise testing.
DIN-Rail mounted or Wall mounted.
Standard: EN 54-18:2005
Description
With a microprocessor, DI-9305E Digital Single Riser
Output Module (the module) can communicate with a
FACP. The module is designed to connect with
70V/100V input audio signal cables or 24VDC input
cable, featuring of checking states of input or output
ports. Checking method can be set.
Connection and Cabling
Fig. 1 shows terminals on the module.
Fig. 1
(Z1, Z2) IN & OUT: Connecting with Signaling Line
Circuit (SLC) loop of FACP, polarity-insensitive.
O1, O2: Output terminals
(I1, I2) IN & OUT: Power input terminals. For
connecting with 24V signal terminals or 70V/100V
audio signal terminals (Note: there is 50kΩ
resistance between I1 and I2).
CODE: connecting with P-9910B programmer.
Recommended Wiring
1.0mm2or above fire cable for all terminals, and
subject to local codes.
Installation
Warning:
Before installing the module, disconnect
power from the loop and verify that the
guide rail is securely installed.
1) Before installation, make sure the enclosure is
in good condition and markings are complete.
2) The module can be mounted on a 35mm
DIN-Rail as shown on Fig. 2.
3) The module can also be wall mounted by 4
mounting screws as shown in Fig. 3.Mouting
space is 67mm x 40.5mm.
Fig. 2
Fig. 3
Application
Connect terminals of I1/I2 with O1/O2. The address
can be programmed in field through a P-9910B Hand
Held Programmer.
Programming Parameters:
In standby state of the programmer, Inputting “456”
and then pressing “Clear” can unlock the
programmer, pressing Fn and then number 3, “—”
(data waiting for programming) will be popped up on
the screen. Writing a parameter and then pressing
“Program”, a “P” will show on the screen meaning
the parameter is programmed.
Operation of Fn and 4can be done as the same as
DI-9305E
Digital Single Riser Output Module
2831-CPR-F2022
GST-0018-01
18
548m/06

30310467 Issue 1.04
Fn and 3.
Press Fn and then number 3, input checking
methods can be set.
1
No checking
others
Checking
Pressing Fn and then number 4, output checking
methods can be set.
1
No checking
others (Default)
Checking
The relationship between the output port resistance
and the product state is shown in the following table:
O1/O2 port
resistance
Output state
< 7.5 kΩ
Fault
> 100kΩ
Fault
other
Normal
The relationship between the input port voltage and
the product state is shown in the following table:
Input port voltage
Input state
<18 V
Fault
>19 V
Normal
The system connection for applying input audio
signals is shown in Fig. 3.
O2
O1
Z1 Z2
Z2
Z1
I2
I1
DI-9305E Module
Field Speaker 1
47kΩ/0.5W
End of Line Resistor
FACP
Field Speaker N
Audio Signal
Fig. 3
The system connection for applying 24VDC is shown
in Fig. 4.
O2
O1
Z1 Z2
Z2
Z1
I2
I1
Controlled Device 1
Controlled Device N
47kΩ/0.5W
End-of-line Resistor
FACP
DI-9305E Module
24VDC Signal
Fig. 4
Specification
Operating Voltage
Loop: 24VDC (16VDC - 28VDC)
Standby Current
Loop≤0.26mA
Action Current
Loop≤0.5mA
Maximum Output
Load
2A@30VDC
Maxi capacity of 60W for 70V
audio input;
Maxi capacity of 60W for 100V
audio input.
Relay Output
Volt-free contact
Programming
Method
Electrically addressed, one
address within 1 - 242.
Active LED
Illuminates red when the relay is
activated, turns off asloop power
cuts down and flashes in other
states.
Fault LED
Illuminates yellow when input
fault occurs and flashes 0.5s on
and 0.5s off when output fault
occurs. The LED is quiet in other
states.
Ingress Protection
Rating
IP30
Operating
Temperature
-10°C - +55°C
Relative Humidity
≤95%, non-condensing
Compatible
DIN-Rail
35mm DIN-Rails
Material and Color
of Enclosure
ABS, white (RAL 9016)
Dimension
(L×W×H)
85.3mm×78mm×33mm
Weight
About 66.6g
Accessories and Tools
Model
Name
Remark
P-9910B
Hand Held
Programmer
Order
separately
RJ-0.5W-47kΩ±1%
Resistor
Provided
Limited Warranty
GST warrants that the product will be free of charge
for repairing or replacing from defects in design,
materials and workmanship during the warranty period.
This warranty shall not apply to any product that is
found to have been improperly installed or used in any
way not in accordance with the instructions supplied
with the product. Anybody, including the agents,
distributors or employees, is not in the position to
amend the contents of this warranty. Please contact
your local distributor for products not covered by this
warranty.
Product warnings and disclaimers
THESE PRODUCTSARE INTENDED FOR SALE
TO, AND INSTALLATION BY, AN EXPERIENCED
SECURITY PROFESSIONAL. UTC FIRE &
SECURITY CANNOT PROVIDE ANY ASSURANCE
THAT ANY PERSON OR ENTITY BUYING ITS

30310467 Issue 1.04
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER”, IS PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY INSTALL
SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-warni
ng/ or scan the following code:
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: [phone] Fax: [phone]
serv[email protected]c.com www.gst.com.cn