GST DI-M9305 User manual

Features
During normal standby, Output port (O1, O2) is
provided with Class B pathway supervision
when connects with 47KΩEOLR (Part Number
30108524).
Occupying one address. It can be modified in
filed.
Output port utilizes AD sampling technology for
precise testing.
Guide rail for installation, easy for construction.
Compatible with GST-M200 and GST-IFP4M Fire
Alarm Control Panels (FACP).
Standard: UL864, NFPA [70, 72].
Description
With a microprocessor, DI-M9305 Digital Single
Riser Output Module can communicate with a FACP.
The module is designed to switch on/off 24VDC
power at its output.
Connection and Cabling
Fig. 1 shows terminals on the module.
Fig. 1
(Z1, Z2) IN & OUT: Connecting with loop of FACP,
polarity-insensitive.
(I1, I2) IN & OUT: Power input terminals. For
connecting with 24VDC power from Listed FACP or
power supply.
O1, O2: Output terminals to 24VDC powered devices
CODE: connecting with P-9910B programmer.
Recommended Wiring
17 AWG or above fire cable for all terminals, and
subject to local codes.
Installation
Warning:
Before installing the module, disconnect
power from the loop and verify that the
guide rail is securely installed.
1) Before installation, make sure the enclosure is
in good condition and markings are complete.
2) The module shall either be installed in a North
America standard metal electrical box.
Minimum size is 4 in. square, 2-1/8 in depth (in
this case, standard box cover is required), or in
a UL Signaling Listed enclosure that provides
minimum wiring entries and spacing as shown
on Fig 2 and Fig 3. Minimum mounting space is
67×40.5mm.
3) The module can be mounted on a guide rail as
shown on Fig 4.
4) The module can also be installed in the
enclosure by 4 mounting screws as shown in
Fig.5.
Fig. 2
DI-M9305
Digital Single Riser Output Module
Fire Alarm
Equipment
47AU
30310200 Issue 1.06

Fig. 3
Fig. 4
Fig. 5
Application
The module is designed to switch on/off connection
between I1/I2 and O1/O2. The address can be
programmed in field through a P-9910B Hand Held
Programmer.
Programming Parameters:
In standby state of the programmer, pressing Fn and
then number 3, “—” (data waiting for programming)
will be popped up on the screen. Writing a parameter
and then pressing “Program”, a “P” will show on the
screen meaning the parameter is programmed.
Parameters used for O1/O2 setting includes:
1 No checking
Any other numbers(Default)
Checking
The system connection is shown in Fig. 6.
O2
O1
Z1 Z2
Z2
Z1
I2
I2
Controlled Device 1
Controlled Device N
47kΩ/1W End-of-line
Resistor
FACP
DI-M9305 Module
I1 I1
in out
24VDC power line to next device
Fig. 6
30310200 Issue 1.06

Specification
SLC Operating
Voltage
Loop: 24VDC
(16VDC - 28VDC)
Power Limited
Power Supply
voltage
Maximum 30VDC.
Power Limited
Power Output
voltage
Regulated if Power Input is
Listed Regulated 24VDC power
supply
Special Application, if Power
Input is Special Application
supplied by Listed compatible
FACP.
Standby Current
Loop≤ 0.26mA
Action Current
Loop≤ 0.5mA
Maximum Output
Load
2A @ 30VDC,0.35PF
Programming
Method
Electrically addressed, one
address within 1 - 242.
Feedback LED
Illuminates red when the relay is
activated, turns off as loop power
cuts down and flashes in other
states.
Fault LED
Flashes yellow 0.5s on and 0.5s
off when output fault occurs. The
LED is quiet in other states.
Ingress Protection
Rating
IP30 (not tested by UL)
Operating
Temperature
0
℃
- +49
℃
Relative Humidity
≤93%, Non Condensing
Material and Color
of Enclosure
ABS, white (RAL 9016)
Dimension
(L×W×H)
85.3mm×78mm×33mm
(with base)
Weight
About 66.6g (with base)
Accessories and Tools
Model
Name
Remark
P-9910B
Hand Held
Programmer
Order
separately
RY-1W-47k±5％End-of-Line
Resistor
Provided
Limited Warranty
GST warrants that the product will be free of charge
for repairing or replacing from defects in design,
materials and workmanship during the warranty period.
This warranty shall not apply to any product that is
found to have been improperly installed or used in any
way not in accordance with the instructions supplied
with the product. Anybody, including the agents,
distributors or employees, is not in the position to
amend the contents of this warranty. Please contact
your local distributor for products not covered by this
warranty.
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P. R. China 066004
Tel: [phone] Fax: [phone]
[e-mail] www.gst.com.cn
30310200 Issue 1.06