gtxlight FX QTFX-B2 User manual
QTFX-B2
Bubble Machine User Manual
160.563UK
User Manual – QTFX-B2 160.563UK
2
QTFX-B2 Bubble Machine – For indoor use only
1. General Introduction :
A portable bubble machine with high quality fan and motor to produce the
best bubbles possible for your party.
Features :
High bubble output
High speed fan with low noise
Easy to empty and clean tank
For best results to be used with QTX ight bubble fluid 160.574UK (1l)
or 160.575UK (5l)
Caution! Please read this manual carefully before
operating! Damage caused by misuse
is not covered by the arranty!
User Manual – QTFX-B2 160.563UK
10
15. Technical specification :
Po er supply 230Vac, 50Hz
Fuse F1A
Po er consumption 40W
RPM 20
Dimensions 290 x 240 x 220mm
Weight 2.0kg
14. Disposal :
Please disposal of the unserviceable device according to the current
statutory requirements.
User Manual – QTFX-B2 160.563UK
3
2. Package Contents :
Please check the contents to ensure that the product has been received in
good condition.
QTFX B2 bubble machine x 1pcs User’s Guide x 1pcs
Power Cord x 1pcs
If you find any accessory is missing or the machine has arrived with any
problems, please contact your local dealer at once. Do not try to fix this item
yourself or you will lose the warranty. Please keep the original package and
invoice for any possible replacement or returned demand.
3. Recommended Fluid:
For the QTFX-B2 bubble machine we strongly recommend the following
fluid which has been specifically formulated for the best results.
QTX Ref
Code Description Size Results
160.574UK 1 itre
160.575UK
High Quality Bubble
Fluid 5 itre
Stable bubbles
User Manual – QTFX-B2 160.563UK
4
4. Setup :
1. Unpack the bubble machine.
2. Place on a flat surface.
3. Pour the contents of the bubble fluid into the front tank so the
bubble wands at the bottom of the wheel are completely submerged.
4. Connect the IEC mains plug and power up.
5. After use unplug from the mains and empty the remaining contents
back in to the bubble fluid container or dispose of appropriately.
6. Clean the front tank fully before the next use.
User Manual – QTFX-B2 160.563UK
9
12. Rear Layout:
7) IEC Socket
8) Fan (DO NOT COVER)
9) ON/OFF Switch
User Manual – QTFX-B2 160.563UK
8
11. Layout:
1) Bubble Wand
2) Bubble Wheel
3) Fluid Tank
4) Mounting Bracket
5) Carry Handel
6) Thumb screw
User Manual – QTFX-B2 160.563UK
5
5. Mounting instruction :
The fixture may be mounted in any position provided there is adequate
room for ventilation and the fluid can not leak.
It is important never to obstruct the front of the machine, fan or vents
pathway. Mount the fixture using a secure clamp.
Adjust the angle of the fixture loosening both knobs and tilting the fixture.
After finding desired position, re-tighten both knobs.
When selecting installation location, take into consideration refilling the
tank and routine maintenance. Safety cables must always be used when
installed at a height.
Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperatures changes or restricted ventilation.
5. Caution! To prevent Mortal Electrical Risk and Long Life Operation :
For your safety, please kindly pay attention to all of the warnings listed
below:
Always plug in the power plug last and disconnect from the mains
when the device is not in use or before cleaning.
Do not install and operate the device in rain or extreme heat,
moisture or dusty environments.
This device is for indoor use only and in a dry environment.
Do not switch on immediately but wait until it reaches to room
temperature if the device has been exposed to drastic temperature
fluctuations.
Do not shake the device and avoid brute force when installing or
operating.
