GunSafe Deluxe Cabinet Service manual

Protecting An Investment
Showcasing Your Collection
Installation
Instruction
Manual GunSafe Cabinet
(pages 1-8)
GunSafe Deluxe Cabinet (pages 9-13)
Seller assumes no obligation for failure of an
architect, installer or home owner to comply
with all applicable law ordinances, building
codes and safety requirements.

Introduction
2©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Tools Needed
Cordless
Screwdriver
(Phillips bit)
Furniture
Pad
Screws for GunSafe
Screws for GunSafe Deluxe
6 – #8 x 13/4"
6 – #8 x 13/4"
26 – #8 x 11/2"
24 – #8 x 11/4"
Hardware (provided)
Scissors
Tin Snips
Tape
Measure
To our Valued Customer:
Thank you for purchasing GunSafe. We are honored to have hand-created the hardwood cabinet
of your choice and are certain it will provide a lifetime of enjoyment.
Your cabinet has been carefully secured for safe delivery to you. Installation is simple and
straightforward if you follow these instructions. Please call us toll-free at 1-877-448-6723
if you have any concerns or need additional information.
In only a short while, your cabinet will be ready to protect your firearms or other sporting
collectibles. Soon, you can showcase your collection to family and friends.
We wish you all the best and once again appreciate your trust in GunSafe.
Sincerely,
William Schlabach
GunSafe founder

Unpacking Your GunSafe Cabinet
3
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 1
Step 2
FRAGILE
It is neccessary for 2 or more people
to set up your GunSafe.
NOTE Use a tin snips to cut plastic bands.
Use a scissors
to remove shrink
wrap, plastic
and tape.
Do Not use knife.
Place furniture pad on
floor in front of pallet.
Remove tape
from small box.
(Base section)
Base is shipped upside down.
NOTE
Fold all
4-flaps back.
Do Not
use knife.
Your GunSafe cabinet will arrive on a
pallet containing two shrink-wrapped boxes.

Unpacking Your GunSafe Cabinet
4©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 3
Step 4
Gently roll base section forward from pallet onto
furniture pad. Keep flaps folded back. Lift box from base section.
Remove all packing materials from cabinet.

Positioning the Top Section
5
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 5
Step 6
Place GunSafe base section approximately 6" forward
from wall where GunSafe display will be placed.
To prevent scratches, drape furniture pad on top
of base section approximately 4" forward from
back side in center of base section.
Place near electrical outlet for light kit.
NOTE
Place top section on base.
Line up flush in back and
center left to right.
While steadying top section,
tilt back and remove furniture pad.

Align and Attach the Top Section
6©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 7
Step 8
Measure left and right sides of cabinet.
Center top section on base.
Flush the back of the top section and the base section.
Use pre-drilled holes.
4
3
2
1
4
3
2
1
Insert 4 – #8 x 13/4"
screws in safe
compartment.
Insert 2 – #8 x 13/4"
screws in storage
compartment.
Unlock safe door. Attach top section to base.
Key interchanges
with locking bar.
NOTE
If drawers are selected,
see page 8 for removal.
NOTE

Plug in the Lights
7
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 9
Unlock with key provided.
Open lid on top of cabinet.
Roll switch
Remove cord attached to
transformer through slot in
back of cabinet. Plug into wall
outlet. Standard 120 AC volt.
Lift and slide cabinet back against the wall.
Do not scratch floor. Do not smash plug in if
lights are plugged in directly behind cabinet.
Touch center right hinge to activate light. Touch
repeatedly for 3-levels of brightness and Off.
If lights do not come
on, activate roll switch
in top of cabinet.
NOTE
Remove Locking Bar
Step 10
Key interchanges with
safe door in base.
NOTE
Lift right side of bar up.
Pull bar slightly to the right.
Remove from cabinet.

Drawer Removal and Installation
8©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 11
Place drawer on runners and
close. Locking devices will
automatically engage runners.
You are now ready to put
your guns into your
GunSafe cabinet.
Squeeze orange handles on locking
devices in front on bottom side of
cabinet. Pull drawer out and up.
Remove top
section of optional
polycarbonate panel
(if purchased).
Standard double
drawers shown
in cabinet and
safe.
Full drawers.
Drawer installation Drawer removal

Unpacking your GunSafe Deluxe Cabinet
9
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 1
Step 2
•Do Not cut with knife.
•Use scissors to remove shrink wrap.
•Use snips to remove banding.
Install Back Center Panel
•Unpack your GunSafe Deluxe cabinet.
•Remove all packing materials.
•Remove drawers from base cabinet.
(Refer to step 10 instructions on page 13)
Refer to GunSafe unpacking instructions steps 1-4.
Attach with #8 x 11/2"
screws in pre-drilled holes.
Install wood top on base
cabinets. Align strips on
underside of wood top
with edge of base cabinet.
Accurate alignment is
necessary for counter
drawer to work properly.
NOTE
Install back center
panel in front of strips
attached to side of
base cabinets.
Wood Top

Attach Wood Top / Place Top Section on Wood Top
10 ©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 3 Step 4
Attach wood top from the bottom in
pre-drilled holes with 24 – #8 x 11/4"
screws. 2 – per corner block.
solid
wood top.
Drape furniture pad on wood top approximately
3" forward from back side in center of wood top.
Align back side of
base cabinet with
straight edge of
solid wood top.
Measure both ends and
make certain top is centered.
NOTE
Place center section on pad.
Hold cabinet steady with one hand towards
top. Tilt back and remove furniture pad.

Measure, Place and Attach Top Cabinets
11
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 5
Step 6
Install 1 – #8 x 11/2" screw in each end from bottom up.
Place left end cabinet on pad and align
flush back and firmly against center cabinet.
Steady cabinet with 2-hands. Tilt back and
remove blanket. Repeat for right side.
Make certain that the end cabinets are still
firmly against center cabinet and flush in
back. Install 1 – #8 x 13/4" screw on each
side in bottom pre-drilled holes.
Measure center section
left and right side. Place in
center and flush in back.
Place furniture pad on left side.
Hold forward 3" from back.
Raised panel ends
should be on outside.
NOTE

4
3
2
1
4
3
2
16
5
Measure and Attach Top Cabinets
12 ©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 7
Step 8
Measure both ends and make certain
cabinets are centered on top. If they are
not, loosen the 2-screws that attach the
center cabinet to the wood top.
4
3
2
1
Measure, align and attach center cabinet to
side cabinets. Install #8 x 13/4" screws in
holes provided.
Adjust as needed
and align cabinets
in back. Install
#8 x 11/2" screws
up thru wood
top into upper
cabinets in holes
provided.
4
3
2
16
5

Plug in the Lights
Step 9
Left and center upper cabinet cords plug into Touch
Dimmer mounted on back of right upper cabinet. Touch
Dimmer plugs into wall outlet. Plug in lights from base
cabinet. (optional feature)
Touch Dimmer
Touch left center hinge on upper right
cabinet to activate lights.
Roll switch
Step 10
You are now ready to move cabinet back against wall. Lift up slightly and put a furniture pad
or rug under each corner of base cabinets. Do not slide before padded as this may scratch the floor.
Drawer Removal
and Installation
13
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Step 11
Grasp bar firmly with
2 hands and swing
bottom to right. Bar will
release at top. Repeat
for 2nd bar. You are now
ready to put guns in
your cabinet. Reverse
procedure to install bars.
Removing Bars From
Horizontal Center Cabinet
Place drawer on runners and
close. Locking devices will
automatically engage runners.
Squeeze orange handles on
locking devices in front on
bottom side of cabinet. Pull
drawer out and up.
Drawer installation Drawer removal
If lights do not come
on, activate roll switch.
NOTE
Unlock
bars.
Refer to page 7 to remove
bars from vertical cabinets.
NOTE

Notes
14 ©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.

From the Desk of William Schlabach, GunSafe founder…
In addition to hand-crafted GunSafe cabinets, our parent company, Wedge Woodworking, builds
custom hardwood cabinetry for a wide range of enjoyment.
For example, our newest division, Meadow Brook Cabinetry, can help define your home with
custom elegance. Our beautiful hardwood creations include kitchen islands and wall cabinets,
dining room hutches and tables, fireplace mantels, entertainment centers, bathroom vanities,
bookcases for office or den, wet bars for recreation and family room, and much more.
We would be pleased to send a a Meadow Brook Cabinetry brochure, and are always available
to answer questions and provide quotations for specialized requests.
We put the “custom” in custom cabinetry. Please call anytime, tollfree at 1-877-612-7665.
Sincerely,
William Schlabach
THANK YOU
15
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.

Designed and
Manufactured by:
160 E CR 240 N
Arthur, IL 61911
Tel: [phone] Manual #1 (August 2007)
©2007 Wedge Woodworking (GunSafe). All rights reserved. Do not copy without written permission.
Protecting An Investment
Showcasing Your Collection