GV BD06 User manual

THERMOSTAT BD06
SEMI-PROGRAMMABLE DIGITAL - WHITE
USER MANUAL
I - INTRODUCTION
II - TECHNICAL PARAMETERS AND MAIN CHARACTERISTICS
Technical parameters
Voltage
AC 230V, 50-60Hz
Amperage
16 A
Working environment
0ºC ~70ºC
Consumption
<0.3 W
Protection index
IP20
Programmable temperature
5ºC ~ 35ºC
Temperature control precision
0.5 ºC
Main characteristics
Programs
3 daily, cyclic active scheduling
Probe reading options
3 (internal, external and both)
External dimensions
86mm x 86mm x 27mm
Material
PC + ABS
Screen background color
Blue
Memory in case of electrical failure
Time and schedules
Child lock
Yes
Installation
Wall-Inserted Type
III - CAUTIONS FOR INSTALLATION
IV - INSTALLATION
1. Separate the thermostat from the display using a screwdriver to press the
groove at the back of the thermostat and pushing the display upwards (g.1).
2. Follow the wiring diagram (g. 2) to connect the power, the heating cable
and the oor probe.
3. Use the two screws provided to x the outer ring and the thermostat base
to the electrician's deep box previously installed (g. 3) and make sure that it
is properly installed.
4. Attach the display to the four projections on the mounting plate and push it
downwards (never press the LCD display directly). The installation is complete.
Turn on the power to test the thermostat.
Fig. 1 - Thermostat opening
1 2 3 4 5
L1 N1 N L
6
NTC
Load
IP 20
AC230V 50/60Hz
current imax:16A
Fig. 2 - Wiring diagram
Fig. 3 - Thermostat Installation
Switch on / o thermostat.
Press for 3s to activate / deactivate child lock
Rotate clock wise Increases the Value, Rotate in the opposite direction
Decreases Value
Fast Press Conrms the option (Enter key)
Pressing for 3s, when released, enters settings mode
P1P2P3
PROG
TIME
F C
F C
SET
ROOM
NTC
0 6 12 18 24
AUTO
Child lock
Programs 1 2 and 3
Energy Saver Mode
Confort Mode
Heating
Hours
24 hours of the day
Programming Symbol
Days of the week
Advanced Options symbol
Set temperature
Room temperature
Automatic mode
Manual mode
Anti-freeze mode
Vacation Mode
V - THERMOSTAT INTERFACE
Funções dos botões
TIME
VI - THERMOSTAT PROGRAMMING
»ON / OFF
Press the button to turn on the thermostat (located on the right side of the
thermostat).
Press the button again to turn o the thermostat and cut the power to the
heating cable or network.
»SETTING THE TIME AND DAY OF THE WEEK
With the thermostat on, press the button and release after 3 seconds to
enter the settings mode.
Turn the knob until the symbol ashes and short press the button
to enter the Hour and day of the week settings.
Rotate the knob to set the minutes and conrm with a short press on the
same button, after the minutes the hours follow with the same procedure.
After setting the hours and pressing the button , you will see the days of
the week ash ( ). 1 represents Monday, 6 represents Saturday
and 7 represents Sunday. After setting the day of the week, press the button
again to exit the menu and wait 5 seconds to exit the settings mode.
Dear User:
Congratulations on chhosing a thermostat. Please refer to this user
manual before installing/using the thermostat.
This thermostat is used to control the temperature of heating cables or
heating mats for electric underoor heating in a given room, wether in a
domestic, commercial or industrial environment.
While we try to provide the best device possible, we are always available for
technical support. If you have any questions, please contact us.
ATTENTION!
When being installed, this thermostat may cause an
electric shock. Make sure the installation is done by
a qualied electrician.
1. Installation should only be done when the electric supply is o, otherwise it can
damage the thermostat and cause an electric shock.
2. Choose the most suitable location for installing the thermostat (about 1,60m
above the oor). It must not be installed at eye level.
3. Installation should not be made at altitudes higher then 2000m above sea level.
Heating Cable / Mat
16A
N (Neutral Wire)
L (Live wire)
AC220V, 50~60Hz
Floor Sensor

»SWITCH BETWEEN MANUAL AND AUTOMATIC MODE
With the thermostat on, press the button quickly to switch between
manual and automatic mode.
»SET TEMPERATURE IN MANUAL MODE
With the thermostat turned on in manual mode, turn the knob to set the
desired temperature.
The thermostat turns on when the probe temperature is lower than the one
set at 1.5ºC and the symbol appears on the screen. This symbol means
that the cable or network is heating up. The thermostat switches o when the
probe temperature is higher than the one set at 1ºC.
»PROGRAMMING ENERGY SAVING MODE / COMFORT MODE
With the thermostat on, press the button for 3 seconds to enter the settings
mode. Choose between the Energy Saving option or the Comfort
option and press the button quickly to enter the selected option.
Rotate the knob to select the desired temperature for the selected mode
and quickly press the button to return to the settings menu.
Wait 5 seconds to exit the settings menu.
»DAILY SCHEDULES P1 P2 and P3
With the thermostat on, press the button for 3 seconds to enter the
settings mode. Select the symbol and quickly press the same button.
It will start at schedule 1 at 00:00, you must turn the button to select
between Energy Saver mode and Comfort mode.
Pressing the button again will switch to 01:00, 02:00 ... until 24:00. After
24h of program 1, it will go to 00h00 of program 2 and then program 3. The
settings of the 3 programs are dened.
These programs will run in a cycle, if you choose P1 it will repeat every day.
»SELECT PROGRAMMING FOR AUTOMATIC MODE
With the thermostat on, press the button for 3s to enter the settings
mode. Select the symbol corresponding to the desired programming,
and quickly press the same button. Quickly press the button again to return to
the settings menu and wait 5 seconds to exit the settings menu. The selected
program symbol will appear on the display.
»VACATION MODE
With the thermostat on, press the button for 3s to enter the settings
mode. Select the symbol and quickly press the same button. it will
dene the number of days it will be absent and after pressing the button
again it will dene the temperature at which the system will work.
Wait 5 seconds and the symbol will remain on the display.
Pressing the button will alternate between the number of days and the
desired temperature without leaving the vacation mode.
To cancel the vacation mode, go to the settings mode and select automatic or
manual mode.
»CHILD LOCK
Regardless of whether the thermostat is on or o, press the side button for
3s. When you release the button, you will see the symbol on the display
indicating that the thermostat is locked.
Repeat the same procedure to unlock the thermostat.
P1P2P3
Error
Cause
Solution
ERR
Floor probe error
Replace floor probe
AUTO
PROG
A1
Correction of temperature reading
A2
Floor probe limit temperature
A3
Child lock: Partial, Total;
A4
High temperature limit of the floor probe
A5
Ambient probe low temperature limit
A6
Minimum temperature correction of the ambient probe
A7
Programmable maximum temperature limit
A8
Non-programmable options
A9
Anti-freeze function
Enter settings mode and select the symbol to enter advanced
settings, turn to move to the next function.
»GENERAL FUNCTIONS TABLE
VIII - ADVANCED SETTINGS
VII - ERROR TABLE
AA Memory (0 - on; 1 - Off)
AB Temperature Unit (ºC / ºF)
AC Descaling function (not applicable)
AD Probes (N1 - room, N2 - floor, N3 - both)
AE Restore Factory Settings
GLOBOVAC Ltd.
Address: Globovac Ltd, 8C Castle Road, Chelston
Business Park, Wellington, Somerset
TA21 9JQ, United Kingdom
Tel Export: [phone]
Tel UK Costumers: [phone]
Email: [email protected]
Web: www.globovac.com
GLOBOVAC Ltd.
Address:
Business Park, Wellington, Somerset
TA21 9JQ, United Kingdom
Tel Export:
Tel UK Costumers:
Email:
Web:
www.globovac.com