Hagan Z01 User manual
Montageanleitung und Anweisungen für den
Fachhandel
Technical and Installation Instructions for
Retailers
Instruction de montage et indications pour le
magasin spécialise
Istruzioni de montaggio e dispositioni per il
commerciante
Instrucciones de montaje de la fijación para travesías
para distribuidores
特約店用ツアービンディング取り付け説明書
08/10 © Hagan Ski GesmbH, Andiesen 11, 4774 St.Marienkirchen, Austria / Art. Nr. TU055-H
ENGLISH
• For a perfect performance of the bind-
ing, everything like mounting, adjusting
and maintenance has to be carried out
by a special retailer according to the
manufacturers guidelines.
• You can only use the original ski stop-
per. If using a ski leash, it has be to be
according to DIN-ISO Standard 11087
• Any modification of the binding, any
improper use or use with non suiting
accessories, raises the risk of an unin-
tended release and therefore is not per-
mitted.
• The hagan Z binding has to be mounted
right on the ski and without any other
external parts, in order to not influence
especially the proper function of the ski
stoppers.
• Not standardized, worn or damaged
boots are due to negatively influence
the release function
• An adjusting range of more than Z is
not standardized. The setting in this
range is at one’s peril. The hagan Z
is TÜV-approved and complies with
DIN ISO 13992 (Tour) and DIN ISO
9462 (Alpine)
• The hagan Z01 suits the following
standardized soles:
Ski boots for on Piste skiing accord-
ing to DIN ISO 5355, touring boots for
adults according to DIN ISO 9523
• Some Dynafit boots and the Scarpa F1
are not compatible
• Leather boots and boots with a flexible
sole are not supposed to be used. We
generally recommend to check both the
boots fit into the binding before mount-
ing and whether the binding can be
adjusted to the specific type of boot.
As a specialized retailer you are obliged
to gage, if necessary newly arrange or
change all units of equipment and match
them with the specific skier according
to DIN/ISO 11088, before you mount or
adjust the functional unit ski/binding/boot.
All parts of equipment have to comply with
current DIN/ISO standards.
• Before mounting or adjusting of a
hagan binding a visual inspection,
especially of used bindings, is required.
• Check whether die release setting of
the binding is adjusted to the specific
skier
• Damages of the surface: check the
surfaces which are in contact with the
ski boot for wear and obvious damages.
Repair or exchange the worn or dam-
aged part.
• Ski brake: check if its broken or bent,
check the function
• Scales: check for readability and
adjustability
• All binding surfaces have to be clean.
Check for contamination and corrosion.
If the ski brake is contaminated, clean
it with a dry or wet rag. Do not use
solvents for the binding clean up, no
silicone and no other lubricants than
the ones approved by hagan. Repair
broken or damaged parts.
• Most skis do have a reinforced area
in the skis centre for the purpose of
mounting the binding. Since ski mate-
rial, construction and dimensions can
vary, it is important to follow the guide-
lines of the particular ski manufacturer.
Also mind the manufacturers sugges-
tions concerning drill diameter, gluing
materials or thread cutting.
• hagan ski touring bindings do have
release mechanisms that are related to
the particular boot sole. For a secure
fixation of the boot into the binding a
few minimum requirements according
to ISO 5355 and 9523, concerning the
geometry, have to be fulfilled.
• Only boots complying with this standard
are to be used. Not suited are the soles
of kids boots DIN ISO 5355 Type C.
• Caution: boots that show a great wear
have to checked about the secure func-
tioning with the binding or whether they
can be fixed into the binding properly
and safely.
1 Toe piece
2 Toe sole holder
3 Adjusting screw lateral release
4 Adjusting scale lateral release
5 Adjusting scale front release
6 Adjusting screw front release
7 Heel cup
8 Opening lever
9 Pole hutch of the opening lever
10 Adjusting screw for forward pressure
and sole length
11 Lock for downhill mode and climbing
aid stage 1
12 Climbing aid lever
13 Main frame
14 Gliding AFD
15 Ski brake pedal
16 Ski brake lever
17 Paper test stripe
18 Adjusting screw sole height (front)
19 Crampon mounting points
20 Pivot shaft
21 Binding screws
22 Rear standing platform
23 Rear side of the main frame
24 Base plate
25 Ski leashes
26 Ring
27 Hook
28 Lug
29 Slit
30 Crampon
31 Crampon adapter
32 Crampon lock
Please check the length of the boot sole
and select the binding size according to
the following scale:
S ~ 255-310mm
M ~ 285-340mm
L ~ 315-370mm
We recommend to always use the smallest
size possible
Before drilling the binding holes, place
your boot in the binding and check
whether the forward pressure can be
adjusted according to (3.8). This is crucial
1
18 2
14
19
15 22
7
6
8
9
5
10
11 12
24
16
13
3
20
21 23
4
08/10 © Hagan Ski GesmbH, Andiesen 11, 4774 St.Marienkirchen, Austria / Art. Nr. TU055-H
ENGLISH
Choose the step drill according to the
manufacturers specification or the follow-
ing criteria:
• Adult ski (wood core with integrated
metal layer) 4.1 x 9mm
Adult ski (foam core) 3.5 x 9mm
• Drill through the guide sleeves of the jig
and make sure the jig is fitted tightly on
the ski.
The fixing screws for ski bindings are
conform to applicable DIN/ISO standards.
For skis the standard claims for a specific
binding mounting range on the ski and
defined tear strength of the screws. A few
ski models require longer fixing screws
since the binding mounting plate is too
deep inside the core for regular screw
lengths. Make sure to pay attention to the
manufacturers instructions.
• Only use genuine ski binding drills
and pay attention to the manufacturers
instructions. Do not use dulled drills.
• Drill with constant pressure and keep
the drill aligned and do not cant it within
the jig.
• The drilling hole has to be deep enough
to give each hole a countersink.
Remove the jig after drilling.
• Turn the ski upside down and knock
all chippings out of the holes with your
hand.
• If the ski has an integrated metal layer
you have to cut threads before mount-
ing.
• Fill the drilling holes with special bind-
ing glue after drilling (not for skis with a
foam core!).
• Make sure that the screws are screwed
in absolutely vertical.
• Fixing the binding to the ski: all screws
have to be tightened and may not be
over twisted. If using an cordless screw-
driver the torque has to be adjusted as
low as possible, in order to avoid an
over twisting of the screw. In any case
the final tightening of the screw should
be carried out by hand.
• If needed or recommended by the
manufacturer, glue can be used as a
lubricant for the binding screws.
3.1 Place the base plate (24) of the
climbing aid (12) on the three drilling
holes at the rear end and screw it in.
3.2 Switch the climbing aid lever (12) up
into stage 1
3.3 Place the rest of the binding unit on
the ski and align it with the base plate
of the climbing aid (24).
3.4 Tighten the two front screws of the
pivot shaft (20)
3.5 Tighten the two rear screws of the
pivot shaft (20)
3.6 Check whether the rear side of
the binding frame (23) is precisely
aligned with the base plate (24) of the
climbing aid (12). (If needed: loosen
the two front screws and align again).
Tighten all screws.
3.7. Check whether the locking device
(11) properly locks the rear end of
the binding frame (23).
3.8 Adjusting the sole length and the for-
ward pressure: Place the boot in the
binding and adjust the heel cup with
the length adjustment screw until the
screw head aligns with the housing of
the rear piece.
3.9 Half open the opening lever for two-
three times and make sure the boot is
properly centered. If needed, repeat
step 3.8.
3.10 Height adjustment front piece:
Pull the toe of the boot upward in the
front. Adjust the toe sole holder (1)
by turning the sole height adjusting
screw (18) until there remains a gap
between the boot sole and the gliding
AFD (14) of 0.5mm (it has to be pos-
sible to pull a 0.5mm paper test stripe
with boots that have sizes (300-305mm
and 335-340mm) which are close to the
particular adjusting ranges of the different
binding sizes (S/M/L).
Always follow the ski manufacturers recom-
mendations. Basically there are two differ-
ent ways (ill. B) To place the binding on
the ski:
a) Skis with a mounting point: most manu-
facturers indicate the mounting position
of the binding either on the skis surface
or on its sidewall, whereas the midsole
mark of the boot has to be aligned with
this mounting point.
b) Skis without a mounting point: toe of the
boot = center of the ski
Bisect the length of the ski and mark it
measured from the tail of the ski. Align the
mounting jig with its marking, align the toe
of the boot and clamp the jig.
Measure the length of your boot sole. Match
up the corresponding point on the scale of
the mounting jig with the assembly marking
for the middle of your boot, and clamp.
Caution:
• Do not bend the ski while drilling
• Make sure to use only the intended
guide sleeves or marks referring to the
particular binding length:
Guide sleeve color of the jig
S silver
M black
L gold
ML
18
1
17
10
08/10 © Hagan Ski GesmbH, Andiesen 11, 4774 St.Marienkirchen, Austria / Art. Nr. TU055-H
ENGLISH
with the crampon mounting points
(19) of the binding frame (13). Now
push the crampon-locking lever (33)
upward until it locks. Dismount in the
reverse order.
3.15 General operation of the binding:
See user manual client
Only use the DIN/ISO recommended
release values! Only use the chart
attached below or the official standard-
adjustment charts to calculate the right
release value for the specific skier.
• Each modification or personal adjust-
ment can be hazardous!
• The adjustment is carried out via the
adjustment screws (3+6)
• The adjustment value is visible on the Z-
value adjusting scale (4+5). Always set
front and toe piece on the same values.
• We strongly recommend to double
check the release value on a speci-
fic binding test device (compare ISO
11110)
• The release value have to be evaluated
for each skier by a specialized retailer,
in order to find the right adjustment
according to DIN/ISO 11088
• All specifications and the adjusted Z-
value have to be entered in a certificate
and be handed out to the client along
with the owner’s manual.
Required information of the skier:
• Weight
• Height
• Age
• Sole length
• Skier type
This classification for a skier’s type has to
be evaluated in a conversation between
retailer and skier in order to find out the
parameters for the setting of the binding.
The parameters are the following:
• Skis without taking risks
• Prefers moderate speed
• Prefers easy, moderate terrain
• Has a basic skiing knowledge and little
shape
• For good skiers with a moderate and
mellow style, preferring to on the safe
side
• Uses a lower Z-setting. The risk of
unintended releases is higher, but the
binding releases in any case, even in a
slight fall.
• Has a basic skiing knowledge and good
shape
• Skis at varying speeds
• Skis every terrain, even difficult slopes
• Applies to every skier who is not cate-
gorized in any of the other types
through this gap between the sole
and gliding AFD).
The toe sole holder screw may
only be operated with a hand screw-
driver! If the sole is too thick a not
standardized, it cannot be fitted in
as described. In this case you have
to grind the sole down as far as the
above mentioned paper stripe test
can be realized.
3.11 Height adjustment of the heel cup
The heel cup (7) adjusts to the height
of the boot heel by itself!
3.12 Check whether the boot is held in the
binding without any clearance. There-
fore you have to turn the boot upward
and sideways by hand.
3.13 Ski brake:
The hagan ski brake is supplied with
a ski brake for a maximum waist width
of 80mm ex works! Additional options
are ski brakes with a waist width of
90, 100 and 115mm.
Mounting and exchange of this
optional brake widths: Loosen the
screws (22), exchange the whole
brake against the optional, new one
and then tighten the screws again
Check: The brake levers have to move
freely along the sidewalls of the ski. If
they touch the sidewalls slightly, you
can carefully bend the levers apart
until they have the desired width.
3.14 Crampons:
Pivot the crampon (30) onto the bind-
ing frame from the bottom up and
slide it forward until the cutouts within
the crampon adapter (31) connect
22
30
3
6
4
5
08/10 © Hagan Ski GesmbH, Andiesen 11, 4774 St.Marienkirchen, Austria / Art. Nr. TU055-H
ENGLISH
• High speeds, difficult slopes
• Skis aggressively and fast
• Prefers steep terrain
• Uses a Z-setting, which is above nor-
mal level. As a consequence the risk of
both, unintended releases and releases
in crashes, is less.
• Find the skiers code according to chart
1. Find out the skiers weight in column
1, the skiers height in column 2. If these
are not found in the same line, use the
code of the line above.
• This code refers to skier type 1.
- For a skier type 2, go one line down
- For a skier type 3, go two lines down
• For a skier being older than 50 years,
again go one line up
• After defining the skiers code, go find
the column in chart 2 which refers to
the sole length (in mm)
• The interface between the column for
the sole length and the line for the
skier’s code specifies the adjustment
value.
• Adjust front- and toe piece accordingly
• Caution, if the interface of the right line
and the column is a blank box, take the
value of the next box in the same line.
• If the binding has proofed unintended
releases the retailer is allowed to adjust
at the behest of the skier:
• First raise the front release value at
the heel piece. Then, but only in case
of still occurring unintended releases,
raise the value for torsional releases at
the toe piece. These settings have to be
carried out progressively by raising the
value in half steps.
If mounting, adjustment and functional test
were carried out properly, the binding has
to be double-checked with a calibrated,
according to DIN/ISO 11110, measuring
device for ski bindings.
This examination should assess and con-
firm with a print out, that the adjusted
nominal values for the release (indicated in
Nm) are within the predefined tolerances.
According to DIN/ISO 11088 a release
value tolerance of +/- 15% is permitted,
corresponding with a chart value between
one line above and one line below the
nominal release value (My, Mz in the col-
umns of the adjusting chart). If the meas-
ured value is lying within these tolerances,
the system can be cleared.
After a correct adjustment of the binding
it is necessary to hand out both the func-
tional unit and an inspection document
(printed or handwritten) to the client.
Carry out the following test after a correct
adjustment of the side release and the
heel piece: Check whether ski binding,
ski and ski boot are conforming to criteria
of visual examination. Important: All used
binding have to be cleaned before exami-
nation. Do not grease sole holder or glide
AFC!
Review of lateral resilience and reset
(symmetry):
Clamp the ski tightly and hit the front part
of the ski boot sideways with the palm of
your hand. Die toe cap of the boot should
deflect around 10mm and has to be back
in its initial center position as quick as
frictionless.
Slow and not exact reset to the center:
• Check whether the ski boot conforms
to DIN/ISO standards or is extensively
worn. If needed, replace it.
• Check the height adjustment of the toe
sole holder and correct if necessary.
• Toe cap of the boot is not precisely
centered in the toe sole holder: check
the forward pressure and correct if
necessary
Non-symmetric release:
• It can occur that the release does not
work symmetrically. If the release values
to the right or to the left happen to be
out of the tolerances, this can be due to
an adjustment failure or due to a non-
fitting boot. Check the following:
• Ski boot:
Does it conform to DIN/ISO standards?
- No excessive wear, damage of the
rims and the sole
- No differing radii at the hold points
• Height adjustment of the toe piece:
Adjustment according to 3.10
• Forward pressure:
Adjustment according to 3.8
Screws at the front piece or the lock
mechanism/climbing aid are loose:
• Check whether screws are missing,
over wound or loose. If necessary
repair or replace or maybe glue it in.
If everything is ok, repeat the release
check. If it still does not function properly,
we recommend consulting the manufac-
turer.
The warranted guarantee by hagan pre-
sumes that the owner’s manual as well as
the warning notices have been followed
and taken care of. Make sure to get the
binding checked according to its function
and correct adjustment regularly or at least
before starting a new ski season. Always
store your skis with the binding locked in
a dry and cool, but frost-protected place.
If the binding is heavily contaminated, only
refine it with water.
Caution: Only use hagan approved lubri-
cants. Otherwise friction values could alter,
leading to unintended releases.
In case of questions or dubiety we are
glad to help anyway.
Tested and approved according to the
DIN/ISO 13992 (Tour) and DIN/ISO 9462
(Alpine) by TÜV-Süd-Product Service
GmbH, Munich.
Made in Germany
All operating and mounting instructions
are available as a PDF database at www.
hagan-ski.com
Artikel Nr. TU0553 / 06.2010
08/10 © Hagan Ski GesmbH, Andiesen 11, 4774 St.Marienkirchen, Austria / Art. Nr. TU055-H
ENGLISH
$BMJCSBUJPODIBSUPGUIFXFJHIUQSPDFEVSFTBDDPSEJOHUP%*/*40
#ZDPOTJEFSBUJPOPGUIFTLJFSUZQFT
4QFFE
1BSBNFUFSPGUIFTLJFS
$PEF0,
'SPNTMPX
UPNPEFSBUF
4LJFSTXIPDPSSFTQPOEUPOFJUIFS
UIFEJTDSJQUJPOPGJUFNOPSUIF
EJTDSJQUJPOPGJUFN
'SPNFBTZ
UPNPEFSBUF -PX
'BTU 4UFFQ
3PUBUJPO.[
JOEB/N
3FMFBTFTFUWBMVF
3FMFBTFTFU
WBMVFUPMFSBODF
3FMFBTFTFUWBMVF
3FMFBTFTFU
WBMVFUPMFSBODF
-JNJUJOHWBMVF -JNJUJOHWBMVF
'PSXBSEJODMJOBUJPO
.ZJOEB/N
"HHSFTTJWF
0OFDPEFMJOFEFFQFS
0OFDPEF
MJOFIJHIFS
5XPDPEFMJOFTEFFQFS
(SPVOET 4UZMF 5ZQF "HF
#ZDPOTJEFSBUJPOPGUIFBHFT
3FMFBTFWBMVFPGUIF
NFBTVSFNFOUUFTUJOHEFWJDF
0SJHJOBMTFUUJOHQBSBNFUFSEFQFOEJOHPOUIFCPPUTPMFMFOHUI
Table of contents
