HAI 68A01-1 User manual

Model 68A01-1
OPERATING MANUAL
Day/Night Dome Camera
(Indoor/Outdoor)
Before installing and using the camera, please read the
instructions thoroughly and retain them for reference.
Document Number 68I01-1 Rev. B
February 2010

Features
1/3" SONY Super-HAD
3.7-12mm Auto Iris Lens
Water resistance IP 66 protection
Wide Range Viewing 3D Covert Bracket Design
E-Z Installation with Attached Cap Design
Anti-Scratch Cover Coating
Specifications
Description Indoor Dome Camera
Power requirements 12VDV / 24VAC Dual Voltage
Synchronization Internal / Line-lock Auto Detect
Image device 1/3” SONY Super HAD CCD
Scanning system P:625 lines, N:525 lines 2:1 interlace
Picture elements NTSC: 542 x 492
Horizontal resolution 420 TV Lines
Current drain 500mA, @12VDC
Minimum Illumination 0 Lux under IR illumination
IR wavelength 700-1100nm (built in 850nm)
OLPF switching Auto switching
S/N Ratio Better than 50 dB
Gain Control ON/OFF Switchable
Focal Length 3.7-12mm@ F1.4
White Balance AWB
Gamma 0.45
BL Compensation ON/OFF Switchable
Product Material Metal
Video Output 1Vp-p, 75Ωcomposite
Vandal Proof 10 Pounds of Sledgehammer Durability
Environmental Rating IP 66
Operating temperature -10°C - 50°C (14Ԭ- 122Ԭ)
* Must use specified and regulated 12VDC/24VAC power supply.
* Specifications are subject to change without any prior notice.

Part Name and Descriptions
A. Camera
B. PC Assembly
C. Back Conduit Entry
D. Side Conduit Entry
E. Housing Mounting Holes
F. Security Screws
G. Conduit Entry Plug
H. Inner Cover Adjustment
Installation
1. Remove dome cover by loosening 4 security screws (use wrench provided).
2. Use the wall anchors and screws provided to mount the housing to a sturdy surface.

Caution
1. Do not touch the surface of the image sensor. If it is touched accidentally, it must be cleaned
using a cloth moistened with alcohol.
2. Before operation, ensure that the supply voltage is correct as specified.
3. Avoid focusing on the sun directly.
4. Do not attempt to service this unit yourself unless you are authorized to do so. Opening or
removing cover may exposure you to dangerous voltage or other hazards.
Connectors
Red wire: connects to +12VDC / 24VAC power source
o(a) Power Source
Black wire: connects to 12VDC Ground / 24VAC power source
o(a) Power Sources
BNC connector: connects to video encoder/monitor
o(b ) Video out, (c) Ground
Configuration
(d) DC Level: Used to adjust the
brightness of the video screen.
(e) Phase Adjustment: Used to
synchronize the power signal and video
signal if the camera is powered from an
AC power source.
(f) Dip Switch: Used to configure various
settings as described below.
DIP SWITCH DIP SWITCH OFF DIP SWITCH ON
1 AI (Auto Iris) AES (Auto Electrical Shutter)
2 BLC OFF (Backlight Compensation) BLC ON (Backlight Compensation)
3 SUP AGC (Super Automatic Gain Control) AGC (Automatic Gain Control)
4 FL ON (Flicker On) FL OFF (Flicker Off)
AI (Auto Iris): Auto Iris Lens is used
AES (Auto Electrical Shutter): Auto Iris Lens is not used
BLC (Backlight Compensation) OFF: Disables this function
BLC (Backlight Compensation) ON: When light is captured and the surroundings are dark, BLC will
brighten the image and compensate using the surrounding light.
SUP AGC (Super Automatic Gain Control): Used in a low light environment
AGC (Automatic Gain Control): Used in a standard light environment
FL (Flicker) On: Suppresses flickering if present
FL (Flicker) Off: Disables this function

Dip Switches 5-8 adjust the delay time for when the camera switches from color to black and white
under IR illumination.
Adjusting the Camera Zoom and Focus
To adjust the zoom and/or focus of the camera:
1. Loosen the zoom ring thumbscrew
2. Turn the zoom ring to set the desired zoom
3. Tighten the zoom ring thumbscrew
4. Loosen the focus ring thumbscrew
5. Turn the focus ring to set the desired focus
6. Tighten the focus ring thumbscrew
3-Axis Gimbal Adjustments
1. Adjust Horizontal angle:
Turn the platform to
adjust the horizontal angle
B (90 degrees), and
C (180 degrees)
2. Adjust Vertical angle:
Turn the platform to adjust
the vertical angle
A (90 degrees)