HAI 68A02-1 User manual

Day/Night Color Bullet Camera
w/ 36 IR LEDs
OPERATING MANUAL
Model 68A02-1

2
Table of Contents
Features 3
Dimensions 3
Parts Name & Descriptions 4
Connections 5
Vari-focal, DC Auto Iris Lens Adjustments 6
OSD Menu Instructions 7
Menu & Setting Details 7
OSD Menu Control 9
OSD Menu ENTER / EXIT 9
Main Menu 10
Specifications 14
Document Number 68I02-1 Rev. A
January 2008

3
Features
• 1/3” CCD Sensor
• High Resolution – 550 TV Lines(Color), 600TV Lines(B/W)
• 3.8~9.5mm Vari-focal Lens, DC Auto Iris
• Day/Night Function with ICR
• 36 IR LEDs
• Auto Switching CDS Sensor
• IR Visual Distance: Up to 100 ft
• 0.1 Lux(Color), 0.00 Lux(B/W, IR LED On)
• Weatherproof (IP65)
• Sun-shield w/ Feed-Through Bracket
• Power: 12VDC/24VAC Dual Voltage
• Compact Size
Dimensions (UNIT: mm)

4
Parts Name & Descriptions

5
Connections
Service Monitor Cable
(suppplied)
• Power connection - Requires 12VDC or 24VAC. (Auto-Polarity Detection and Protection)
• All camera model are supplied with second video output on the camera module. To use
this feature along with a service monitor, second monitor cable/connector is required.
•Power connection - Requires 12VDC or 24VAC (Auto-Polarity Detection and
Protection).
•This camera is supplied with a second video output on the camera module.
T
o use this feature along with a service monitor, a second monitor and cable is
required.

6
Vari-focal, DC Auto Iris Lens Adjustments
1Untighten Main Body Ring cover from the Base Ring.
4
2
2
Loosen Zoom & Focus screws and make necessary adjustments as shown.
Field of View: Telephoto( T ) to Wide( W )
Focus: Near( N ) to Infinity( )
2
T------- W
------- N
Adjust Focus
Adjust Angle for Field of View
3
Tighten Main Body Ring back to the Base Ring.
Please refer to Page 10 of this manual for further instructions.
4

7
OSD Menu Instructions
Menu & Setting Details
LENS
SHUTTER
WHITE BALANCE
BACKLIGHT
AGC
DNR
DSS
• DC
• NONE
• FLK
• ESC
• ATW
• MANUAL
• AWC
• OFF
• LOW
• MIDDLE
• HIGH
• OFF
• NORMAL
• HIGH
• OFF
• LOW
• MIDDLE
• HIGH
• OFF
• AUTO
BRIGHTNESS
BRIGHTNESS
MODE
RED
BLUE
N/A
BRIGHTNESS
BRIGHTNESS
LIMIT
1-70 (25)
1-70 (25)
NORMAL
SPECIAL
0-256(32)
1-256(39)
1-70 (25)
1-70(25)
x2 - x128 (x8)
Main Menu

8
OSD Menu Instructions
Menu & Setting Details
SPECIAL • CAMERA ID
• COLOR
• DZOOM
• SYNC
• MOTION DET
• PRIVACY
• MIRROR
• SHARPNESS
• RESET
• RETURN
OFF
ON
ON
AUTO
BW
OFF
ON
INT
OFF
ON
OFF
ON
OFF
ON
ON
OFF
x1- x8 (x1)
AREA SEL AREA 1, 2, 3, or 4
AREA STATE ON/OFF
TOP
DOWN
LEFT
RIGHT
AREA SEL AREA 1, 2, 3, or 4
AREA STATE ON/OFF
TOP
DOWN
LEFT
RIGHT
LEVEL 0~31 (8)
Main Menu

9
OSD Menu Instructions
OSD Menu Control
MENU KEY - Used to access menu mode, Also used to confirm the setting
UP / DOWN KEY - Used to choose the desired menu selection.
LEFT / RIGHT KEY - Used to choose the desired menu feature adjustment.
OSD Menu ENTER / EXIT
A. OSD MENU ENTER
• Push Menu Key
B. OSD MENU EXIT
• Press EXIT Menu from Main Menu

10
OSD Menu Instructions
Main Menu
A. LENS
This function is used to adjust the brightness of the screen.
• DC: The brightness can be adjusted in DC mode. The brightness can be
adjusted within the range of 1 to 70.
B. SHUTTER
This function is used to control the condition and speed.
• NONE: Shutter is off.
• FLK: Select ‘FLK’ mode when flickering occurs on the screen due to imbalance
between illumination and frequency.
• ESC: Select ‘ESC’ mode for automatic control of shutter speed. The speed is
controlled automatically according to the brightness of the screen.
C. WHITE BALANCE
This function is used to balance the screen color.
• ATW (Auto Tracking White Balance):
Select ‘ATW’ when using within the color temperature range of 1,800°K to 10,500°K (Ex.
Fluorescent light, outdoor, sodium vapor lamp or inside tunnels)
• AWC (Auto White Balance Control):
Select SETUP button while the camera is directed at a piece of white paper to obtain the
optimum state under current illumination. If the environment including the light source is
changed, you have to adjust the white balance again.
• MANUAL (Auto White Balance Control):
Select ATW or AWC first before selecting Manual mode. Once Manual mode is selected,
select SETUP. Set the appropriate color temperature, and increase or decrease the red
and blue color values while monitoring the color changes on the object. The Manual mode
enables finer adjustment.

11
OSD Menu Instructions
D. BACKLIGHT
This function is used when there is strong light in the background.
• OFF: Backlight Compensation is off.
• LOW: Select if there is little light in the background.
• MIDDLE: Select if there is moderate light in the background.
• HIGH: Select if there is a great amount of light in the background.
E. AGC
This function is used to adjust the level of gain. As the level of gain increases, the screen
gets brighter and the level of noise also increases.
• OFF: The gain is fixed at 6dB.
• NORMAL: The gain increases or decreases within the range of 6dB to 30dB.
• HIGH: The gain increases or decreases within the range of 6dB to 34dB.
F. DNR
This function is used to reduce the signal noise on the screen.
• OFF
• LOW
• MIDDLE
• HIGH
G. DSS
This function is used to help maintain a bright, clear screen image by automatically detect-
ing changes in the level of light in low light conditions.
• OFF: DSS function off.
• AUTO: Low light level auto mode.
* DSS does not operate if SHUTTER is set to MANUAL
* DSS does not operate if AGC is turned OFF.

12
OSD Menu Instructions
H. SPECIAL
CAMERA ID
• ON: CAMERA ID is displayed on the monitor.
If the CAMERA ID has not been set, please follow these directions:
1. Press the LEFT or RIGHT button to turn the Camera ID mode to “on”.
2. Press SETUP for the camera ID screen.
3. By pressing the RIGHT, LEFT, UP and DOWN keys, select up to 15 letters
for your camera ID.
4. Press SETUP again to lock those letters.
5.Continue to select letters for the next space.
6. Repeat these steps to input the complete ID.
7. Move the cursor to ‘POS’ and press SETUP again.
8. The name will appear on the top left hand corner.
9. Use the LEFT, RIGHT, UP, and DOWN keys to select the position of the
Camera ID.
10. Press ‘END’ and then press the SETUP button to complete ID input.
• OFF: Camera ID is not displayed on the monitor.
COLOR
The functions in COLOR mode are used to change the appropriate mode for daytime or
night-time.
• ON: The COLOR mode is selected electronically.
• AUTO: The COLOR mode is operated for daytime, and it automatically converts
to BW mode for night-time.
• BW: The COLOR mode is operated for night time.
DZOOM
This function is used when Digital Zoom is preferred.
• On
• Off

13
OSD Menu Instructions
SYNC
This function is used when synchronization with the legacy system is needed.
• INT: Internal Synchronization.
• LL: External Synchronization.(Optional)
MIRROR
• OFF: Cancels the inversion.
• ON: Sets a horizontal image inversion.
SHARPNESS
• OFF: Sharpness mode is off.
• ON: Enables to adjust the sharpness of the video image.
To adjust, follow these instructions:
Press the SETUP button.
Press the LEFT and RIGHT button to adjust the sharpness.
RESET
This function resets all of the settings in the menu to the level set by the
manufacturer for shipment.
RETURN
This function returns to the SETUP menu.
I. EXIT
Saves all the setting menus and then exits.

14
Specifications
Description
Video Format
Image Sensor
Sync System
Scanning system
Electronic Shutter
Main Video Output
Service Monitor Output
Horizontal Resolution
Min. Illumination
S/N Ratio
Day/Night Function
36 IR LEDs
Lens Options (DC Auto Iris)
Camera Control & Setup
Operating Temperature
Operating Humidity
Weatherproof
Power Consumption
Power Requirement
Day/Night Color Bullet Camera
NTSC PAL
1/3” CCD
Internal / Line Lock(Optional)
525 Lines, 2:1 Interlaced
1/60 ~ 1/100,000 sec. 1/50 ~ 1/100,000 sec.
1.0 Vp-p Composite, 75 ohm
1.0 Vp-p Composite, 75 ohm
550 TV Lines(Color), 600 TV Lines(B/W)
0.1 Lux(Color), 0.00 Lux(B/W, IR LED On)
More than 50dB(AGC Off)
ICR
LED Distance: upto 100 ft.
3.8~9.5mm
OSD Menu
-15ºC ~ +50ºC
Within 90% RH
IP65
1Amp(w/ LED On)
12VDC/24VAC Dual Voltage
* Must use specified and regulated 12VDC/24VAC power supply.

15