HAI 68A01-1 User manual

3-AXIS GIMBAL VARI-FOCAL
INDOOR DOME CAMERA

Features 3
Dimension 5
Base Installations 7
8Connection
93-Axis Gimbal Adjustments
9How to Open the Gimbal Cover
10Vari-focal, DC Auto Iris Lens Adjustments
11OSD Menu Instructions
4Specifications
Part Name and Descriptions 6
Contents
2

3
Features
1/3” CCD
550 TV Lines
3.8~9.5mm DC Auto Iris Lens
0.1 Lux(Normal), 0.002 Lux(DSS On)
Separate Camera Control Board
-OSD Menu
-Service Monitor Output
12VDC/24VAC Dual Voltage
4” Polycarbonate Bubble
3-Axis Gimbal
Flush Mount Housing w/ Surface Mount Plate in single package
Aluminum Mounting Accessories (Option)
Compact size

Specifications
4
* Must use specified and regulated 12VDC/24VAC power supply.
* Specifications are subject to change without any prior notice.
Video Formats
Image Sensor
Sync System
Scanning system
Electronic Shutter
Main Video Output
Service Monitor Output
Horizontal Resolution
Min. Illumination
S/N Ratio
Lens (DC Auto Iris)
Auto Iris Control
Camera Control & Setup
Operating Temperature
Operating Humidity
Power Consumption
Power Requirement
NTSC PAL
1/3" CCD
Internal
525 Lines, Interlaced 625 Lines, Interlaced
1/60 ~ 1/100,000 1/50 ~ 1/100,000
1.0 Vp-p Composite, 75 ohm
1.0 Vp-p Composite, 75 ohm
550 TV Lines
0.1 Lux(Color), 0.002 Lux(DSS On)
More than 50dB(AGC Off)
Vari-focal: 3.8~9.5mm
DC Level Button
OSD Menu
-5ºC ~ +45ºC
Within 90% RH
500mA
12VDC/24VAC Dual Voltage
Description Indoor Dome Camera

Dimension (Unit:mm)
5
70
112
145 70
109
46
46 83 109
83
33
20
50
146
103
108
40
18
50
99146

Parts Name and Descriptions
6
3
4
1
6
8
7
11
2
10
13
5
12
9
1. Lens
2. Power Input Connector
12VDC/24VAC Dual Voltage
3. Video Output Connector – BNC
4. Service Monitor Output Connector
5. Camera Control Board
6. Safety Wire
7. Bubble
8. Dome Cover Ring
9. Flush Mount Base
10. Surface Mount Plate
11. Assembly Screw (Torx M4x9)
12. Assembly Screws (Philips M4x10)
13. Mounting Screws
Caution : Do not aim the camera directly into the sun.
(Philips ST4x30)

Base Installations
7
1. Remove dome cover by loosening 3 screws (Torx M4x9) .
Use Torx wrench provided with the package.
2. Surface Mount:
Using four ST4x30 screws, mount surface plate to a sturdy surface.
Using four M4x10screws,
affix flush mount base to surface plate.
(For flush mount application, disregard this step)
3. Flush Mount
Using four ST4x30 screws, affix flush mount base to a sturdy surface.
Surface Mount
Flush Mount
12
3
Torx M4x9
M4x10
Plastic Dowels
ST4x30
A
A'
ST4x30

8
Connection
20cm
Service Monitor Output
12VDC/24VAC
CCTV Monitor
Service Monitor
- Power connections: Requires 12VDC or 24VAC.
-
This camera is supplied with a second video output on the
camera module. Use this feature along with a service monitor.
UP
DOWN
RIGHT
LEFT

9
3-Axis Gimbal Adjustments
Gimbal Cover
Gimbal Base
Point-A
Point-B
The Gimbal mechanism yields maximum rotation and placement as shown below
1. Pan 355 °
2. Tilt 85 °3. Horizontal
Rotation
355°
How to Open the Gimbal Cover
This Dome Camera hasavari-focal lens
integrated inside the Gimbal. To make
focal/focus adjustments, the Gimbal
cover needs to be temporarily removed . If lens
adjustments are not necessary, skip to Page 10.
Step-1
As shown on the right, hold the Gimbal base
firmly in place with one hand.
Step-2
Gently press Points A & B with other hand and
pull the Gimbal cover off.
Step-3
Make necessary lens adjustments.
Step-4
Replace the Gimbal cover by gently pressing
back onto the Gimbal base.

1. Remove the Gimbal cover from the Gimbal base.
2. Loosen Zoom & Focus screws and make necessary adjustments as shown.
Field of View: Telephone (T) to Wode (W)
Focus: Near(N) to infinity(∞)
3. Replace the Gimbal cover back to the Gimbal base.
10
Vari-focal, DC Auto Iris Lens Adjustments
Zoom
Focus
Gimbal
Cover
Adjust Focus
Adjust Angle for Field of View
T W
∞N
UP
DOWN
RIGHT
LEFT
OSD Menu Button