Haier HB80 User manual

B80
Single Door Vertical Cooler
HB80
SingleDoor Vertical Cooler
Installation and Operating Instructions
MAN6819
Rev. 1.0 Oct. 2006edition.
Copyright© 2006
SKOPE IndustriesLimited.
All rights reserved.
SKOPE IndustriesLimited reserve the
right toalter specifications without notice.
is a registeredtrade
mark of SKOPE Industries Limited.
i
TRADE MARK INFRINGEMENT
TheSKOPE trade mark onthis product is infringedif the owner, for thetime
being, does any of the following:
•Applies thetrade mark to theproduct aftertheir state, condition,get-up
or packaging has been altered in anymanner
•Alters, removes (includingpart removal) or obliterates (includingpart
obliteration) thetrademark ontheproduct
•Applies any other trade mark to the product
•Addsto the product any writtenmaterial that is likely to damage the
reputation ofthetrademark
Noticeof the above contractual obligations passes to:
•Successors or assigns of the buyer
•Future owners ofthe product

B80
Single Door Vertical Cooler
1INSTALLATION
1.1Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.3Positioning the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2OPERATION
2.1Cabinet Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.3Temperature Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3MAINTENANCE
3.1Cabinet Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3.2Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.3Advanced Servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.4Contact Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
TABLE OF CONTENTS
ii

4B80
Single Door Vertical Cooler
1.1Safety Information
When using any electrical appliance, safety precautions should
always be observed. Read these instructions carefully and retain for
future reference.
•This appliance is not intended for use by young or infirm persons
unless they have been adequately supervised by a responsible
person to ensure that they can use the appliance safely. Young
children should be supervised to ensure that they do not play
with the appliance.
•Disconnect the cabinet from the mains power supply before
attempting any cleaning or maintenance.
•Do NOT use this appliance for other than its intended use.
•Do NOT cover the grilles or block the entry or exhaust of airflow
by placing objects up against the refrigeration unit.
•Do NOT probe any opening.
•Only use this appliance with voltage specified on the rating label.
•Ensure adequate ventilation of the refrigeration unit.
•Be careful not to touch moving parts and hot surfaces.
•Regulations require that all electrical work be carried out by
authorised persons. For your own safety, and that of others,
ensure this is done.
•If the supply cord becomes damaged, it must be replaced by a
SKOPE authorised service agent, or similarly qualified person,
in order to avoid a hazard.
Disposal
Care must be taken when disposing of this product to avoid hazards.
Please contact SKOPE Customer Services for advice regarding
disposal of this product.
INSTALLATION
1

5
B80
Single Door Vertical Cooler
1.2Unpacking
Remove all packing material from the inside and outside of the
cabinet, including the foam base and all adhesive tape holding the
cabinet accessories.
Shelves
Remove the packing material from both shelves and then position
the shelves into the cabinet at the desired heights. The bottom shelf
has hooks on the back which lock the shelf in position.
Figure 1: Cabinet Shelves
Evaporator Fan
Top Shelf
Bottom Shelf
INSTALLATION
1

6B80
Single Door Vertical Cooler
1.3Positioning the Cabinet
Power Supply
This cooler is rated 220-240 Va.c. and will draw a maximum of 1.1
Amps. Do not overload the power supply. The 3-core mains flex,
which exits behind the refrigeration unit, should be retrieved before
the cabinet is positioned.
Ventilation
When positioning the cabinet, adequate clearance must be
maintained for ventilation. For efficient operation of the cooler, it is
essential that adequate ventilation be provided around the cabinet.
Normal maximum operating conditions are 40°C at 40% RH
(Climatic Class 5).
This cooler should not be recessed or enclosed in a cabinet. It is
designed for free-standing installation only. The recommended
clearance on both sides and at the back of the cabinet is 50mm.
Location
When positioning the cabinet:
•Avoid direct sunlight and warm draughts etc.
•Allow adequate space for the door to open fully.
•Ensure the cabinet is positioned on a level surface so the door
shuts and seals correctly, and to prevent the condensate tray
from overflowing.
Levelling
This cooler has a levelling bolt located underneath the door hinge.
After final positioning, the levelling bolt can be adjusted to stabilise
the cabinet. Turn the levelling bolt clockwise to raise or anti-
clockwise to lower the cabinet.
INSTALLATION
1

7
B80
Single Door Vertical Cooler
2.1Cabinet Operation
Connect the cooler to the mains power supply and check operation
of the refrigeration unit and cabinet interior light. After moving the
cooler, allow the cabinet to stand for at least 30 minutes before
connecting to the power supply.
If the cooler has been disconnected from the power supply for any
reason, allow about 10 minutes before switching it back on. This
allows the refrigeration system pressure to equalise before the
system is restarted.
Refrigeration Unit
The evaporator fan (inside the cabinet) should operate continuously
from the time the cabinet is plugged in. This may be verified by
checking air movement inside the cabinet. The thermostat will click
when it cycles on and off.
Cabinet Light
The cabinet interior light is controlled by the light switch beside the
thermostat knob inside the cabinet. The fluorescent lamp will require
aperiod of time to stabilise following initial start up. See page 10 for
instructions on replacing the fluorescent lamp.
OPERATION
2

8B80
Single Door Vertical Cooler
2.2Loading
The cooler should be left running for 30 minutes to allow the cabinet
to cool down before loading with product. When loading the cabinet
shelves with product:
•Allow air space around all the product, for even cooling and
efficient operation of the cooler.
•Do not exceed a maximum of 30 kg per shelf.
•Do not allow products to overhang the front or rear of the
shelves, as this will effect air flow.
•Do not obstruct air flow from the evaporator fan.
OPERATION
2

9
B80
Single Door Vertical Cooler
2.3Temperature Adjustment
The storage temperature of the cooler can be regulated to suit
different ambient temperature by turning the thermostat knob,
located inside the cabinet (see Figure 2 below).
The thermostat knob is graduated from 0 through to 6, with 1being
the warmest and 6 being the coldest. The normal temperature
controller setting is between 3 and 5.
•To make colder - turn the thermostat knob clockwise.
•To make warmer - turn the thermostat knob anti-clockwise.
Note: Turning the knob to ‘0’ will switch the refrigeration unit OFF.
Figure2: Thermostat Knob
Thermostat Knob
LightSwitch
OPERATION
2

10 B80
Single Door Vertical Cooler
3.1Cabinet Light
The cabinet interior light is fitted with a 5 Watt fluorescent lamp. To
replace the lamp:
1.Disconnect the cabinet from the mains power supply.
2.Remove the light cover by carefully bending out the side clips.
3.Pull the fluorescent lamp out of the lamp holder.
4.Replace with a maximum 5 Watt fluorescent lamp.
5.Carefully align the side clips on the light cover and fit back into
place.
6.Reconnect the cabinet to the mains power supply.
Figure3: ReplacingtheFluorescent Lamp
Fluorescent Lamp
Lamp Holder
MAINTENANCE
3