Halex Electronic Dartboard with Parlor Cabinet User manual

Electronic
Dartboard
withParlor
Cabinet
Assembly Instructions
Halex
TM
REGENT SPORTS CORPORATION • 45 RANICK ROAD • HAUPPAUGE • NEW YORK 11788

LIMITED 90 DAY WARRANTY
This Halex product is warranted to be free from defects in workmanship
or materials at the time of purchase for a period of 90 (ninety) days.
Should any evidence of defects appear within the limited warranty period
after the date of purchase, Regent Sports will either send replacement
parts or advise of another course of action. A list of replaceable parts can
be found on the parts order form page of this manual. Parts not listed
on this order form are not replaceable. This warranty covers normal
consumer use and does not cover failures, which result from alterations,
accidents, misuse, abuse, or neglect.
For prompt warranty service and special offers, please register your
Halex product by visiting our website at: www.regent-halex.com and
enter the following unique registration number followed by the item num-
ber of your dartboard found on the cover of this manual: 1ZAK7 ____.
You must register your product within 30 days of purchase to be eligible
for warranty service. Please make sure to visit our website to order
additional parts not covered under the warranty, as well as on-line
instruction manuals and new product information.
A purchase receipt or other proof of date of purchase will be required
before warranty service is performed. Requests for warranty service
can be provided by e-mailing the customer service department at
[email protected] or by calling customer service at:
877-516-9707 (Toll Free)
10:30 AM to 6:30 PM, EST (Dec. through Feb.)
10:30 AM to 5:00 PM, EST (March through Nov.)
Or send request in writing to:
Regent Sports Corporation
45 Ranick Road
Hauppauge, NY 11788
Attn: Halex Customer Service
This warranty gives you specific legal rights and you may have other rights
that vary from state to state.

PARLOR CABINET ASSEMBLY INSTRUCTIONS
Before removing cabinet components from carton, clear an area on the floor at least 9-10 feet long by 6-8 feet wide in the
proximity of the location where the cabinet will be used. The assembled cabinet will stand approximately 7 feet tall. If the cleared
area is not carpeted, we suggest laying down area rugs or multiple layers of news paper or other cushioning material to prevent
the wood grained surfaces from being scratched during assembly. Next remove all panels and hardware from carton and place
them near the cleared area for easy access. Additional hardware has been included in a small bag for your convenience.
Cabinet Fasteners and Pins (shown actual size) Cabinet Door Hardware
N. Cabinet Door
Handle and
Attaching Screw
P. Tili-Down
Doorknob and
Attaching Screw
Q. Spring Loaded
Door Hinge
Assembling The Cabinet
The cabinet is assembled in two sections, starting with
the top section and adding the bottom section to it. Each
of the following steps should be accomplished in order
and just as described to facilitate ease and quickness of
assembly.
Exploded View of
Top Cabinet Section
3. Top Right Arched
Side Panel
2. Top Left Arched
Side Panel
B. Barrel Nut
B. Barrel Nut
B. Barrel Nut
A. Panel Bolt
A. Panel Bolt
1. Top Panel
5. Top Section Shelf
C. Dowel Pin
C. Dowel Pin
4. Connector Panel
6. Tilt-Down Door Panel
D. Hinge Pin
D. Hinge Pin
P. Tilt-Down Doorknob
Note: Top
section back
panel is not
shown in
this view.
R. Anchor Screw
Allen Wrench

G. Insert 4 barrel nuts (B), with
slotted ends out, into holes
at top and bottom of top right
arched side panel (3).
H. Position top right arched side
panel (3) into top panel (1).
Carefully align dowel pins (C)
on shelf and steel hinge pin
(D) on tilt-down door with
mating holes in right side
panel and press panels
together.
I. Secure connector panel (4)
to top right arched side
panel (3) using 2 panel bolts
(A) through connector panel
(4) into barrel nuts (B) and
tighten securely. Repeat for
top panel (A).
2. Top Left Arched
Side Panel
2. TopLeft Arched
Side Panel
1. Top Panel
1. Top Panel
A. Panel Bolt
A. Panel Bolt
B. Barrel Nuts
4. Connector Panel
4. Connector Panel
5. Top Section Shelf
C. Dowel Pins
C. Dowel Pins
6. Tilt-Down
Door Panel D. Hinge Pin
P. Tilt-Down Doorknob
Doorknob Screw
3. Top Right Arched
Side Panel
Masking Tape
A. Panel Bolt
Panel Bolts
B. Barrel Nuts
B. Barrel Nuts
D. Hinge Pin
STEP 1. Top Cabinet Section Assembly.
A.Place top left arched side panel (2) with its back edge on the floor (curved edge up). Insert 2 barrel nuts (B) into holes
at top of panel (1) with slotted ends of nuts out and pointing toward top panel. Slot in barrel nut permits aligning nut
with screw, see Detail A.
B. Place top panel (1) (black side in and unfinished edge down) perpendicularly against side panel (2) as shown. Using 2
panel bolts (A), through top panel (1) and into barrel nuts (B), secure to side panel (2).
C. Inset 2 dowel pins (C) into holes in
side panel (2) and press shelf (5),
with unfinished edge down, onto
dowel pins.
D. Attach wooden tilt-down doorknob
(P) to beveled side of tilt-down door
panel (6) with screw provided.
E. Press 2 steel hinge pins (D) into
holes on side edges of tilt-down door
panel (6).
F. Press hinge pin (D) on tilt-down door
panel (6) into mating hole on bottom
front corner of side panel (2). Pivot
panel down against shelf (5) and
secure temporarily with strip of
masking tape, see illustration below.
Slot is
aligned with
bolt hole
Bolt Hole
Bolt Hole
Detail A. Positioning Barrel Nuts in Side Panels

STEP 2. Bottom cabinet section assembly.
A. Turn top section over so that back of top section is facing upward.
B. Attach anchor block (9) to bottom left side panel (7) using 2 anchor block screws (E), see Detail B. Repeat for
bottom right side panel (8). Be sure that the anchor block is positioned flush to the bottom edge of the side panel
that is facing the floor. Use the pre-drilled guide holes to ensure proper alignment.
C. Place end of left bottom side panel (7), with anchor block (9) attached, against connector panel (4) of top cabinet
section. Holes in bottom side panel (7) should be facing inward.
D. Align anchor block holes with embedded anchor nuts in connector panel (4) on top cabinet section. (Place a few
magazines approximately 5/8" thick under bottom end of side panel to help facilitate aligning anchor holes.)
E. Secure panels tightly with 2 Allen head anchor screws (F) using anchor screw Allen wrench provided. Repeat for
right side panel.
Top Cabinet Section
F. Allen Head
Anchor Screws
Embedded
Anchor Nuts
9. Anchor Block
10. Face Brace Panel
Face Brace Panel Pilot Holes
G. Face Brace
Panel Screws
7. Bottom Left
Side Panel
4. Connector
Panel
8. Bottom Right
Side Panel
11. Cross
Brace Panel
C. Dowel Pins
F. Place face brace panel (10) between side panels (7) & (8). The finished side of the face brace should be facing
towards the top of the cabinet. Insert 2 dowel pins (C) on the inside of each of the bottom side panels. The
inner holes on the bottom of the side panels are to be used for these dowel pins.
G. Insert 4 face brace screws (G) through the outside holes in the side panels and screw loosely into face brace
panel. The two outer holes on the bottom of each side panel (7) & (8) are used for the wood screws.
H. Insert 4 dowel pins (C) into empty remaining holes in bottom side panels (7) & (8) just above the face brace
panel. Press cross brace panel (11) into dowel pins (C).
I. Press panels together and tighten face brace panel screws (G) securely.
Note: Attaching bottom
section of cabinet to top
section with front sides
down will make it easier
to attach back panels to
cabinet.
9. Anchor
Block
7. Bottom Left
Side Panel
E. Anchor
Block Screws
Detail B

STEP 3. Attaching Back Panels
A. Place bottom section back panel (12) onto bottom cabinet section with mitred edge (notched edge) towards top
cabinet section and mitre facing up.
B. Secure panel at both sides and bottom only using flathead cabinet screws (H) provided. Do not attach top end
of back panel (12) to connector panel (4) at this time.
C. Place top section back panel (13) onto top cabinet section with “black” side down and dart board mounting holes
closer to bottom cabinet section. Bottom end of top back panel (13) should fit snugly over mitred section of
bottom back panel (12). Mating holes in both back panels should line up.
D. Secure top back panel (13) to top cabinet section and mitred edge of bottom back panel (12) with flathead
cabinet back screws (H) provided. Screws should be used completely around both panels.
12. Bottom Cabinet
Back Panel
Overlap edge of
top panel (13)
onto mitred edge
of bottom panel (12)
13. Top Cabinet
Back Panel
H. Back Panel
Screws
4. Connector
Panel
H. Back Panel
Screws
Note: Attach bottom
section back panel first,
then overlap top panel
and screw through both
panels at mitre joint into
cabinet frame.

Hinge
Mounting
Pilot Holes
STEP 4. Attaching Cabinet Doors and Mounting Dartboard
A. Turn assembled cabinet onto left side. Place magazines under bottom end of bottom side panel for temporary support.
B. Open 2 hinges (Q) and position over pilot holes in left cabinet door (14). Attach hinges using 2 panhead hinge screws
(J) and 1 flathead hinge center screw (L) for each hinge. Note: Hinge center screw (L) is used in the center hole of
each hinge and set flush with hinge surface, allowing hinge to fold flat when door is closed, see detail below. Do not
attached door handle (N) at this time.
C. Place left cabinet door (14) with hinged side facing up in open position against left side panel (7).
Note: Cabinet doors are symmetrical and can be used for either left or right side.
D. Position cabinet door hinges over pilot holes in left side panel (7) and secure using 1 panhead hinge screw (J) in the
center of each elongated hinge hole. This will allow for adjustment if necessary when cabinet is standing.
E. Place cabinet on its right side and repeat Step 4.D above for right cabinet door (14). Hinges are spring loaded and will
keep doors closed.
F. Place cabinet on its back. Align dartboard mounting holes with back panel holes. Use a flash light to help locate the
dartboard mounting holes. The holes in the back panel have threaded inserts for dartboard mounting screws. (The
dartboard is supplied with necessary screws to secure it to the cabinet.)
G. Use 4 screws supplied. Do not over tighten screws to avoid chipping or cracking dart board housing.
Dartboard mounting holes have
threaded inserts for screws
J. Panhead
Hinge Screw
J. Panhead
Hinge Screw
J. Panhead
Hinge
Screw
14. Left Cabinet Door
Dart Board
Mounting Screws
Supplied with
Dart Board
Q. Cabinet
Door Hinge
L. Hinge
Center Screw
Q. Cabinet
Door Hinge
Wall
Mounting
Holes
Inside Surface
of Cabinet Door
Helpful Hint:
To facilitate attaching dart board, a length of
stiff wire placed through one of the dart
board mounting holes can be used to align
the holes in the dart board with the threaded
mounting holes in the cabinet back panel.

STEP 5. Attaching Optional Stabilizer Foot Braces
K. Stabilizer Foot
Brace Bolt
15. Stabilizer
Foot Brace
8. Right
Side Panel
Each Stabilizer
Foot Brace has 5
predrilled holes
for attaching to
matching holes
in each side
panel.
M. Nut
A. Attach optional stabilizer foot brace (15) to right side panel (8), (rounded edges away from side panel), using 5
stabilizer foot bolts (K) and 5 nuts (M).
Note: Both stabilizer foot braces (15) are symmetrical and can be attached to either side panel (7) or (8).
B. Turn cabinet on opposite side and repeat Step 5, A above for the left side panel stabilizer foot brace.
Note: Optional stabilizer foot braces must be attached if cabinet is to be used free standing.
Do not use stabilizer foot braces if cabinet is to be anchored to a wall. The foot braces extend well
beyond the back of the cabinet and will prevent the cabinet from being set flush against the wall.

Door Handle
Screws
N. Cabinet
Door Handle
Wall
mounting
holes
16. Interior Bottom
Cabinet Storage Shelves
Shelf Mounting Notches
D. Steel Shelf
SupportPins
17. Dart Holder
Electric
Cord
Access
Hole
To electric
wall outlet
STEP 6. Attaching Door Handles and Interior Shelves.
A. Stand cabinet upright against wall making sure it does not tip forward. Secure cabinet to wall using wall mounting
screws (S) through wall mounting holes in bottom back panel.
Note: Optional stabilizer foot braces (15) must be attached if cabinet is to be used free standing.
B. With cabinet doors opened, attached 2 door handles (N) using 4 panhead screws supplied with handles.
C. Insert 4 steel shelf support pins (D) into holes in each side panel (7) and (8) for shelf support.
D. Place 2 interior bottom cabinet storage shelves (16) with notched sides down onto shelf support pins. Notches should
slip over pins, securing shelves in place.
E. Attach dart holders (17) to the inside of each door using 2 screws (G) as shown in detail below. Position wide holes up.
F. Close cabinet doors and check alignment of both doors. If doors are not aligned satisfactorily, loosen side panel hinge
screws, re-align and re-tighten screws securely. Carefully remove tape securing tilt-down door.
17. Dart
Holder
Cabinet
Door
Wide
holes up
G. Screws
Dart Holder Assembly

PARTS ORDER FORM
If for some reason you are missing any assembly parts for your Halex dart game, please
call the Regent Sports Customer Service line at [phone] (toll free) between the
hours of 10:30 am and 6:30 pm EST or go online at www.regent-halex.com for parts ordering.
Please refer to the REGENT SPORTS LIMITED WARRANTY concerning missing and/or
defective parts.
Parts also may be ordered by filling out the form below. Please fill in all the information and
return to:
REGENT SPORTS CORP.
45 RANICK ROAD
HAUPPAUGE, NEW YORK, 11788
ATTN: CUSTOMER SERVICE
REGENT SPORTS CORP. requires that all orders for replacement parts must be paid by
check, money order, VISA, or MC. Cash is not accepted. Please make all checks or money
orders payable to REGENT SPORTS CORP. Please note all prices include shipping and
handling.
Name of Purchaser: __________________________________________________________
Address: ___________________________________________________________________
City: _______________________________________________________________________
State: ______________________________ Zip Code: ______________________________
Phone: _____________________________
Electronic Dartboard Parts / Accessories
PART # DESCRIPTION QUANTITY PRICE TOTAL COST
100-64675 12 Darts with Tips $8.95
100-64670 AC Adapter $11.95
68750 48 Pack Soft Tips $5.95
68835 Soft Tip Accessory Kit $9.95
192-64395-1 Dartboard Mounting Screws $1.00
Refer to next page for Parlor Cabinet Parts