Hans Grohe Focus M42 220 2jet 71800007 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 3
Lesezeichen
中文 2
English 3
Focus M42 220 2jet
71800007
Focus M42 180 2jet
71801007

2
中文
安装 (参见第页6)
安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
技术参数
工作压强： 最大1MPa
推荐工作压强： 0,1-0,5MPa
测试压强： 1,6MPa
(1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
热力消毒: 最大70°C/4分钟
• 自动防止回流
• 该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
调节 (参见第页8)
热水温度调节。如果使用即热式喷头，则不建议
安装热水阀门。
清洗 (参见第页10)
保养 (参见第页12)
单向阀必须在符合国家或当地的法律的情况下按
照EN806-5定期检查(至少一年一次)。
大小 (参见第页4)
流量示意图 (参见第页4)
备用零件 (参见第页13)
操作 (参见第页9)
• 水嘴旋转不可超过360º，否则会导致软管受
损。
• 汉斯格雅建议，清晨或在水流长时间停滞后，
前半升水不作饮用水使用。
问题 原因 补救
龙头不灵活 - 阀芯损坏，结垢 - 更换阀芯
龙头滴水 - 阀芯损坏 - 更换阀芯
水从螺纹底座中流出 - 连接软管没有完全旋入基体 - 用手拧紧连接软管
- 连接软管的O形环损坏 - 更换O形环
热水温度过低 - 温度限制器设置错误 - 设置温度限制器

3
English
Assembly (see page 6)
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Thermal disinfection: max. 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking
water!
Symbol description
Do not use silicone containing acetic acid!
Adjustment (see page 8)
To adjust the hot water limiter. Using a hot water limiter
in combination with a continuous flow water heater is
not recommended.
Cleaning (see page 10)
Maintenance (see page 12)
The check valves must be checked regularly according
to EN 806-5 in accordance with national or regional
regulations (at least once a year).
Dimensions (see page 4)
Flow diagram (see page 4)
Spare parts (see page 13)
Operation (see page 9)
• Do not rotate the spout further than 360º or damage
to the hose will result.
• Hansgrohe recommends not to use as drinking water
the first half liter of water drawn in the morning or
after a prolonged period of non-use.
Fault Cause Remedy
Mixer stiff - Cartridge defective, calcified - Exchange cartridge
Mixer dripping - Cartridge defective - Exchange cartridge
Water escaping at the threaded
base
- connection hoses not completely
screwed into basic body
- Tighten connection hoses by hand
- O-ring at the connection hose
defective.
- Exchange O-ring
Hot water temperature too low - Hot water limiter incorrectly set - Set hot water limiter

4
ca. 500
125
148
85
15°
207
219
400
224
28Ø
68
165
34Ø
550
52Ø
max. 60
182
97
G1/2
1
2
360°
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912 15 18 21 24 27 30
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
Focus M42 220 2jet
71800007
Maße Durchflussdiagramm

5
1
2
360°
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912 15 18 21 24 27 30
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
ca. 500
125
148
85
15°
207
224
28Ø
68
165
52Ø
183
364
182
97
34Ø
550
max. 60
G1/2
Focus M42 180 2jet
71801007
Maße / Durchflussdiagramm

6
SW 10 mm
SW 24 mm
(4 Nm)
(3 Nm)
1.
2.
3b
1.
2.
!
max. 35 mm
max. 60 mm
3b
1 2
3a 4
5 6
Montage

7
80
1.
CLICK
3.
4.
2.
> 2 min
(1 Nm)
7 8
910
11 12
Montage

0,3 MPa
60 °C 10 °C
+
+
21 3
4 5
6 7
4.
3.
1.
2.
3.
1.
2.
6 x
36°C
38°C
43°C
50°C
55°C
60°C
17 x
SW 4 mm
SW 4 mm
(5 Nm)
SW 4 mm
SW 4 mm
8
Justierung

9
开 / open
热 / hot 冷 / cold
关 / close
Bedienung

10
•
•
•
•
•
•
•
•
•
•
•
Hansgrohe
Hansgrohe
www.hansgrohe-int.com/guarantee
QuickClean
QuickClean
10
QUICK
CLEAN
Reinigung

11
English
Cleaning Recommendation for Hans-
gro
he Products
T
oday, modern sanitary and kitchen tapware, showers,
accessories, washstands, tubs and radiators consist of
ve
ry different materials to comply with the needs of the
mar
ket with regard to design and functionality.
To
avoid damage and reclamations, it is necessary to
consider cer
tain criteria when cleaning.
Wi
th regard to caring for the Hans-
gro
he products, the following must in
principle be heeded:
• Only use cleaning material which is explicitly
provided for this type of application.
• Never use cleaning materials, which contain
hydrochloric acid, formic acid, chlorine pale lye or
acetic acid, as they cause considerable damage.
• Phosphorus acidic cleaners are only conditionally
applicable.
• Mixing cleaning agents is not permitted, generally.
• Never use cleaning materials or appliances with an
abrasive effect, such as unsuitable cleaning powders,
sponge pads or micro fibre cloths.
• The instructions of the cleaning agent manufacturers
have to be followed absolutely.
• Cleaning has to be carried out with a specified
cleaner dosage, contact time, object-related and
adapted to the needs.
• The building up of calcifications has to be removed by
cleaning regulary.
• When using spray cleaners, spray the cleaning
solution onto a soft cloth or sponge, never directly
onto the Hansgrohe products, as the atomised spray
could enter openings and gaps in the Hansgrohe
products and cause damage.
• After cleaning rinse thoroughly with clean water to
remove any cleaner residue.
• The use of steam cleaners is not permitted. The high
temperatures can damage the products.
Important
R
esidues of toiletries such as liquid soaps, shampoos and
shower gels, hair dyes, perfumes, aftershave and nail
varnish can also cause damage.
Here too: Carefully rinse with water after use to remove
residues.
Likewise, do not store any cleaning agents or chemicals
under the products, for example in a vanity unit, as the
vapours may damage the products.
The damage of already damaged surfaces will
deteriorate under the effect of the cleansers.
Components with damaged surfaces
must be exchanged, otherwise there
could be an injury danger.
Damage caused by improper treatment will not be
covered by our guarantee.
Warranty
Hansgrohe guarantees to the consumer that this product
is free of production faults. If evertheless any defect is
detected within 5 years from date of purchase, Hans-
grohe will remedy this defect free of charge. Y
ou will find
the conditions and details of this guarantee at
www.hansgrohe-int.com/guarantee. Please contact your
contracting party to claim your rights under this
guar
antee. This guarantee does not affect the customer‘s
rights under the respective national legislation.
QuickClean
The QuickClean cleaning function only needs a small
manual rub over to remove the lime scale from the spray
channels.
11
QUICK
CLEAN

12
1
1
2
2
Wartung

13
97735000
93253000
(46x2)
97406000
93344000
93346000
96338000
95561000
(600 mm)
92482000
(600 mm)
95140000
92500000
(400g)
95507000
(1500 mm)
92730000
93340000
(71800007)
93341000
(71801007)
95008000
98156000
(36x2)
98193000
(32x2)
98127000
(11x2)
98422000
(7x1,5)
97523000 97827000
(8x1,75)
98365000
98211000
(21x2,5)
93343000
95910000
94074000
93342000
98173000
(22x1,5)
97548000
Focus M42 220 2jet
71800007
Focus M42 180 2jet
71801007
Serviceteile

14

15

Hansgrohe · Auestraße 5 - 9 · D-77761 Schiltach · Telefon [phone] · Telefax +49 (0) 7836/511440
E-Mail: [email protected] · Internet: www.hansgrohe.com
06/2020 9.06179.52