Hans Grohe Metris Select M71 200 1jet 14845007 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 3
Lesezeichen
中文 2
English 3
Metris Select M71 200 1jet
14845007
Metris Select M71 200 2jet
73819007

2
中文
安装 (参见第页4)
安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
• 首次调试时和维护作业之后，管接头中的空气
可能产生噪音。大约使用管接头15次后噪音
消失。
技术参数
工作压强： 最大1MPa
推荐工作压强： 0,1-0,5MPa
测试压强： 1,6MPa
(1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
热力消毒: 最大70°C/4分钟
该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
调节 (参见第页8)
热水温度调节。如果使用即热式喷头，则不建议
安装热水阀门。
保养 (参见第页9)
单向阀必须在符合国家或当地的法律的情况下按
照EN806-5定期检查(至少一年一次)。
大小 (参见第页10 )
流量示意图 (参见第页10 )
清洗 (参见第页12 )
备用零件 (参见第页14)
操作 (参见第页16)
• 汉斯格雅建议，清晨或在水流长时间停滞后，
前半升水不作饮用水使用。
• 通过手柄打开阀门时出水口可能流出少量水。
问题 原因 补救
龙头不灵活 - 阀芯损坏，结垢 - 更换阀芯
龙头滴水 - 阀芯损坏 - 更换阀芯
水从螺纹底座中流出 - 连接软管没有完全旋入基体 - 用手拧紧连接软管
- 连接软管的O形环损坏 - 更换O形环
热水温度过低 - 温度限制器设置错误 - 设置温度限制器
更换龙头后，在打开可调龙头时
流量减少
- 安装了错误的可调龙头 - 更换可调龙头(#98463000)
调节按钮不好用 - 调节按钮脏污 - 清洁调节按钮，给O形环
#95962000(19x1,5)上油

3
English
Assembly (see page 4)
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
• During initial start-up and after servicing, air in the
fittings can cause noise. After switching the jet on
and off about 15 times, the noise will stop.
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Thermal disinfection: max. 70°C / 4 min
The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
Adjustment (see page 8)
To adjust the hot water limiter. Using a hot water limiter
in combination with a continuous flow water heater is
not recommended.
Maintenance (see page 9)
The check valves must be checked regularly according
to EN 806-5 in accordance with national or regional
regulations (at least once a year).
Dimensions (see page 10 )
Flow diagram (see page 10 )
Cleaning (see page 12 )
Spare parts (see page 14)
Operation (see page 16 )
• Hansgrohe recommends not to use as drinking water
the first half liter of water drawn in the morning or
after a prolonged period of non-use.
• Minor leaking may occur briefly at the spout when
opening the fitting via the lever.
Fault Cause Remedy
Mixer stiff - Cartridge defective, calcified - Exchange cartridge
Mixer dripping - Cartridge defective - Exchange cartridge
Water escaping at the threaded
base
- connection hoses not completely
screwed into basic body
- Tighten connection hoses by hand
- O-ring at the connection hose
defective.
- Exchange O-ring
Hot water temperature too low - Hot water limiter incorrectly set - Set hot water limiter
Low flow with Select valve after
valve replacement
- Improper Select valve installed - Replace Select valve
(#98463000)
Select button stiff - Select button soiled - Clean Select button and grease
#95962000 (19x1,5) O-ring

4
(3 Nm)
max. 45 mm
max. 60 mm
75°
75°
105°
45°
105°
45°
24 x 15°
1b
1a 2
3
Montage

5
(3 Nm)
!
4 5
6 7
8 9
Montage

6
SW 17 mm
SW 19 mm
(4 Nm)
SW 10 mm
SW 24 mm
(4 Nm)
93095000
(700 mm)
92569000
95664000
(600 mm)
10 11
12 13
14 15

7
2.
1.
SW 17 mm
1.
2.
> 2 min
SW 19 mm
(4 Nm)
80 mm
16 17
18 19
20
Montage

60 °C 10 °C 0,3 MPa
6 7 8
4 5
31 2 SW 3 mm
3 x
SW 3 mm
(5 Nm)
36°C
38°C
43°C
60°C
55°C
50°C
8
Justierung

9
SW 17 mm
SW 17 mm
SW 19 mm
SW 19 mm
(4 Nm)
1 2
3 4
5
WartungWartung

10
Ø 34
Ø 47
min.100
36
4
55650700
G 3/8
G 1/2
320
208
4 °
c a . 5 0 0
221
235
Ø 28
Ø 47
5
Ø 28
max. 60
Metris Select M71 200 1jet
14845007
Metris Select M71 200 1jet
14845007
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912 15 18 21 24 27 30
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
Maße / Durchflussdiagramm

11
Ø 34
Ø 47
min.100
36
4
55650700
320
208
4 °
c a . 5 0 0
221
235
Ø 28
Ø 47
5
Ø 28
max. 60
G1/2
G 3/8
Metris Select M71 200 2jet
73819007
Metris Select M71 200 2jet
73819007
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912151821242730
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
1
2
1
2
Maße / Durchflussdiagramm

12
•
•
•
•
•
•
•
•
•
•
•
Hansgrohe
Hansgrohe
www.hansgrohe-int.com/guarantee
QuickClean
QuickClean
12
QUICK
CLEAN
Reinigung

13
English
Cleaning Recommendation for Hans-
gro
he Products
T
oday, modern sanitary and kitchen tapware, showers,
accessories, washstands, tubs and radiators consist of
ve
ry different materials to comply with the needs of the
mar
ket with regard to design and functionality.
To
avoid damage and reclamations, it is necessary to
consider cer
tain criteria when cleaning.
Wi
th regard to caring for the Hans-
gro
he products, the following must in
principle be heeded:
• Only use cleaning material which is explicitly
provided for this type of application.
• Never use cleaning materials, which contain
hydrochloric acid, formic acid, chlorine pale lye or
acetic acid, as they cause considerable damage.
• Phosphorus acidic cleaners are only conditionally
applicable.
• Mixing cleaning agents is not permitted, generally.
• Never use cleaning materials or appliances with an
abrasive effect, such as unsuitable cleaning powders,
sponge pads or micro fibre cloths.
• The instructions of the cleaning agent manufacturers
have to be followed absolutely.
• Cleaning has to be carried out with a specified
cleaner dosage, contact time, object-related and
adapted to the needs.
• The building up of calcifications has to be removed by
cleaning regulary.
• When using spray cleaners, spray the cleaning
solution onto a soft cloth or sponge, never directly
onto the Hansgrohe products, as the atomised spray
could enter openings and gaps in the Hansgrohe
products and cause damage.
• After cleaning rinse thoroughly with clean water to
remove any cleaner residue.
• The use of steam cleaners is not permitted. The high
temperatures can damage the products.
Important
R
esidues of toiletries such as liquid soaps, shampoos and
shower gels, hair dyes, perfumes, aftershave and nail
varnish can also cause damage.
Here too: Carefully rinse with water after use to remove
residues.
Likewise, do not store any cleaning agents or chemicals
under the products, for example in a vanity unit, as the
vapours may damage the products.
The damage of already damaged surfaces will
deteriorate under the effect of the cleansers.
Components with damaged surfaces
must be exchanged, otherwise there
could be an injury danger.
Damage caused by improper treatment will not be
covered by our guarantee.
Warranty
Hansgrohe guarantees to the consumer that this product
is free of production faults. If evertheless any defect is
detected within 5 years from date of purchase, Hans-
grohe will remedy this defect free of charge. Y
ou will find
the conditions and details of this guarantee at
www.hansgrohe-int.com/guarantee. Please contact your
contracting party to claim your rights under this
guar
antee. This guarantee does not affect the customer‘s
rights under the respective national legislation.
QuickClean
The QuickClean cleaning function only needs a small
manual rub over to remove the lime scale from the spray
channels.
13
QUICK
CLEAN

14
92566880
95962000
(19x1,5)
92567000
98463000
13913000
92570000
98112000
(8x2)
92583000
92569000
98365000
98211000
(21x2,5)
98198000
(38x2,5)
92909000
97548000
97548000
92500000
96099000
95581000
(14,5x9,5x2)
98758000
98422000
(7x1,5)
98422000
(7x1,5)
93093000
93094000
93090000
95049000
93095000
(700 mm)
98445000
(M6X6)
92627000
92527000
(27x1,5)
97685000
98865000
98398000
(23x2)
98464000
(40x1,5)
97523000
98156000
(36x2)
95664000
(600 mm)
(17,8x8,4x2)
96456000
95291000
Serviceteile
Metris Select M71 200 1jet
14845007

15
95962000
(19x1,5)
92567000
98463000
95910000
93412XXX
98112000
(8x2)
92583XXX
92569000
(1,5 m)
98365000
98211000
(21x2,5)
98198000
(38x2,5)
92909000
97548000
97548000
92500000
96099000
95581000
(14,5x9,5x2)
96556000
(600 mm)
98422000
(7x1,5)
98422000
(7x1,5)
93093000
93094XXX 93090XXX
95049000
95896000
(700 mm)
98445000
(M6X6)
92627000
92527000
(27x1,5)
97685000
98865000
98398000
(23x2)
98464000
(40x1,5)
97523000
98156000
(36x2)
95664000
(600 mm)
(14,5x9,5x2)
93342000
96456000
95291000
92566880
93395000
Serviceteile
Metris Select M71 200 2jet
73819007

16 Hansgrohe · Auestraße 5 - 9 · D-77761 Schiltach · Telefon [phone] · Telefax +49 (0) 7836/511440
E-Mail: [email protected] · Internet: www.hansgrohe.com
04/2020 9.05450.53
关 / close 关 / close
1.
2.
开 / open
热 / hot 冷 / cold
Bedienung