Hans Grohe Talis S2 Variarc Eco User manual

ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 3
Lesezeichen
中文 2
English 3
Talis S² Variarc
14877007
Talis S² Variarc
14872007

2
安全技巧
装配时为避免挤压和切割受伤，必须戴上
手套。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安
装后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲
洗和检查。
• 请遵守当地国家现行的安装规定。
技术参数
工作压强： 最大1MPa
推荐热水温度： 0,1-0,5MPa
测试压强： 1,6MPa
 (1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
热力消毒: 最大70°C/4分钟
该产品专为饮用水设计！
中文
清洗(参见第页10)
如果水流减少，清洁位于花洒头和软
管之间的过滤网。
操作(参见第页8)
汉斯格雅建议，清晨或在水流长时间
停滞后，前半升水不作饮用水使用。
备用零件(参见第页14)
流量示意图
(参见第页7)
普通水流
花洒
安装(参见第页4)
大小(参见第页6)
调节(参见第页13)
热水温度调节。如果使用即热式喷
头，则不建议安装热水阀门。
请勿使用含有乙酸的硅胶！
符号说明
保养(参见第页12)
单向阀必须在符合国家或当地的法律
的情况下按照DINEN1717定期检查
（至少一年一次）。

3
Safety Notes
Gloves should be worn during installation to
prevent crushing and cutting injuries.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for
transport damages. After it has been installed, no
transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
Technical Data
Operating pressure: max. 1 MPa
Recommended hot water temp.: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Thermal disinfection: max. 70°C / 4 min
The product is exclusively designed for drinking
water!
English
Cleaning (see page 10)
If the waterflow drops, clean the filter
located between hose and handspray.
Operation (see page 8)
Hansgrohe recommends not to use
as drinking water the first half liter of
water drawn in the morning or after a
prolonged period of non-use.
Spare parts (see page 14)
Flow diagram
(see page 7)
 Normal spray
 Regular
Assembly (see page 4)
Dimensions (see page 6)
Adjustment (see page 13)
To adjust the hot water limiter. Using a
hot water limiter in combination with
a continuous flow water heater is not
recommended.
Do not use silicone containing acetic
acid!
Symbol description
Maintenance (see page 12)
The check valves must be checked
regularly according to DIN EN 1717 in
accordance with national or regional
regulations (at least once a year).

4
Montage
Montage
1a
32
1b
4 5
CLICK
(3 Nm)
SW 10 mm SW 24 mm
(4 Nm)

5
Montage
(1 Nm)
6 7
8 9
1210 11
> 2 min

6
Maße
150°
132
Ø 34
855
max. 60
G 1/2
ca. 500
177
Talis S² Variarc 14877007
G 1/2
Talis S² Variarc 14872007

7
Durchflussdiagramm
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912151821242730
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
1
2
Talis S² Variarc
14877007
1 2
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912 15 18 21 24 27 30
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l
/
sec
Talis S² Variarc
14872007

8
Bedienung
开 / open 关 / close
热 / hot 冷 / cold

9
Bedienung
1 2
3 4
1.
2.

10
重要说明
肥皂，洗发水、沐浴液、染发剂、香水、刮胡
水、指甲油的残留也会对产品造成损伤。
此处：使用后要小心地用清水将剩余物冲洗干
净。
同样在产品下方不得存放洗涤剂和化学药品，
例如不可放在用于洗脸盆的梳洗柜中否则挥发
气体将损坏产品。
在已经损伤的表面继续使用清洁剂会给表面造
成更大的损伤。
表面损坏的部件必须更换，否则会有
受伤的危险。
不按规定进行清洁而造成的任何损坏不在本公
司产品保修范围之内。
QuickClean
有了QuickClean，手工清洁功能，要去掉喷头上
的水垢，只需简单地搓除即可。
担保
Hansgrohe向用户保证，该产品无制造缺陷。
如果自购买之日起五年内出现缺陷，Hansgrohe
将免费排除。保证条件和详情见www.
hansgrohe-int.com/guarantee。在提出保修的权
利时请联系您的合同方。本保证不涉及有关国
家法律规定的消费权
汉斯格雅产品的清洁建议
现代的卫浴龙头、厨房龙头、花洒、配件、盥
洗台、浴盆和加热器采用的制造材料非常迥
异，以适应产品外形设计和使用功能的市场需
求。
为了避免产品损坏和由此引发的投诉及争议，
必须在使用和清洁产品时遵循有关规程。
在保养汉斯格雅产品时，原则上必须注意：
• 只能使用那些有明确注明是适用于本产品的
清洁剂。
• 不允许使用含有盐酸、蚁酸、氯漂或醋酸的
清洁剂，因为这些清洁剂会给产品表面造成
严重的损伤。
• 含磷酸的清洁剂必须在特定条件下使用。
• 不允许将两种以上清洁剂混合使用。
• 不允许使用具有研磨作用的清洁工具和设
备，如不适合的清洁粉末、海绵垫或超细麦
克布。
• 必须严格遵守清洁剂生产厂商的使用说明。
• 严格遵守清洁剂的用量和作用时间，决不允
许清洁剂的作用时间长于规定值。
• 定期的清洁以预防水垢。
• 不允许将清洁剂直接喷射到汉斯格雅产品
上，因为喷雾会进入汉斯格雅产品的开口部
分和缝隙中而造成损害。首先将清洁剂喷在
软布上，再用软布进行清洁。
• 清洁之后必须用足够的清水冲洗，以彻底去
除残留的吸附物（清洁剂）。
• 不允许使用蒸汽清洗机，高温会损害产品。
中文
Reinigung
QUICK
CLEAN

11
• After cleaning rinse thoroughly with clean water to
remove any cleaner residue.
• The use of steam cleaners is not permitted. The
high temperatures can damage the products.
Important
Residues of toiletries such as liquid soaps, shampoos
and shower gels, hair dyes, perfumes, aftershave and
nail varnish can also cause damage.
Here too: Carefully rinse with water after use to
remove residues.
Likewise, do not store any cleaning agents or chemi-
cals under the products, for example in a vanity unit,
as the vapours may damage the products.
The damage of already damaged surfaces will dete-
riorate under the effect of the cleansers.
Components with damaged
surfaces must be exchanged,
otherwise there could be an injury
danger.
Damage caused by improper treatment will not be
covered by our guarantee.
QuickClean
The QuickClean cleaning function only needs a small
manual rub over to remove the lime scale from the
spray channels.
Warranty
Hansgrohe guarantees to the consumer that this
product is free of production faults. If evertheless
any defect is detected within 5 years from date of
purchase, Hansgrohe will remedy this defect free of
charge. You will find the conditions and details of this
guarantee at www.hansgrohe-int.com/guarantee.
Please contact your contracting party to claim your
rights under this guarantee. This guarantee does
not affect the customer‘s rights under the respective
national legislation.
Cleaning Recommendation for Hans-
grohe Products
Today, modern sanitary and kitchen tapware,
showers, accessories, washstands, tubs and radiators
consist of very different materials to comply with
the needs of the market with regard to design and
functionality.
To avoid damage and reclamations, it is necessary to
consider certain criteria when cleaning.
With regard to caring for the Hans-
grohe products, the following must in
principle be heeded:
• Only use cleaning material which is explicitly
provided for this type of application.
• Never use cleaning materials, which contain
hydrochloric acid, formic acid, chlorine pale lye or
acetic acid, as they cause considerable damage.
• Phosphorus acidic cleaners are only conditionally
applicable.
• Mixing cleaning agents is not permitted, generally.
• Never use cleaning materials or appliances with
an abrasive effect, such as unsuitable cleaning
powders, sponge pads or micro fibre cloths.
• The instructions of the cleaning agent manufactur-
ers have to be followed absolutely.
• Cleaning has to be carried out with a specified
cleaner dosage, contact time, object-related and
adapted to the needs.
• The building up of calcifications has to be removed
by cleaning regulary.
• When using spray cleaners, spray the cleaning
solution onto a soft cloth or sponge, never directly
onto the Hansgrohe products, as the atomised
spray could enter openings and gaps in the Hans-
grohe products and cause damage.
English
QUICK
CLEAN

12
Reinigung
Wartung
Reinigung
Wartung
1 2
1 2

0,3 MPa
0,3 МПа
0,3 ﻣﻴﺠﺎﺑﺴﻜﺎل
60 °C 10 °C 0,3 MPa
+
21 3
4
6 7
4.
3.
1.
2.
3.
1.
2.
6 x
5
36°C
38°C
43°C
50°C
55°C
60°C
17 x
SW 4 mm
SW 4 mm
(5 Nm)
SW 4 mm
SW 4 mm
13
Justierung

14
Serviceteile
95049000
95560000
96338000
95008000
98365000
95562000
96920000
95498000
92730000
94074000
98212000
(41x2)
92500000
(400g)
95507000
(1500 mm)
97523000
98193000
(32x2)
97209000
(M37x1,5)
SW 30 mm
97735000
95140000
(M4x20)
SW 4 mm
95561000
(600 mm)
SW 19 mm
97489000
(900 mm)
Talis S² Variarc
14877007
13913000
(M24x1)
97827000
(8x1,75)
98422000
(7x1,5)
97548000

15
Serviceteile
95049000
95560000
96338000
95008000
98365000
95562000
88659000
93218000
95498000
92730000
97350000
(DIN-DVGW)
98212000
(41x2)
92500000
(400g)
95507000
(1500 mm)
97523000
98193000
(32x2)
97209000
(M37x1,5)
SW 30 mm
97735000
95140000
(M4x20)
SW 4 mm
95561000
(600 mm)
SW 19 mm
97489000
(900 mm)
Talis S² Variarc
14872007
13913000
(M24x1)
97827000
(8x1,75)
98422000
(7x1,5)
97548000

Hansgrohe · Auestraße 5 - 9 · D-77761 Schiltach · Telefon [phone] · Telefax +49 (0) 7836/511440
E-Mail: [email protected] · Internet: www.hansgrohe.com
10/2018 9.06379.51