Hans Grohe Metris S 04135 0 Series Installation guide

Metris S
04135XX0
Metris S
04126XX0
Talis S
04136XX0
Talis S
04127XX0
Focus S
04137XX0
Focus S
04128XX0
Solaris E
04138XX0
Solaris E
04129XX0
Allegro E
04139XX0
Allegro E
04130XX0
Swing C
04143XX0
Swing C
04134XX0
Metro E
04140XX0
Metro E
04131XX0
Installation Instructions / Warranty

2
Two-hole thermostatic tub filler -- requires rough 04125181
04135XX0 04136XX0
04137XX0 04138XX0
04139XX0 04140XX0
04143XX0

3
Three-hole thermostatic tub filler -- requires rough 04124181
04129XX0
04128XX0
04127XX0
04126XX0

4
Technical Information
Recommended water pressure 45 - 72 psi
Recommended hot water temp. 120�- 140�F*
Max. hot water temp 165�F*
Max. flow rate 8 gpm
Max. flow rate – handshower 2.5 gpm
Safety stop 100° F
*Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.
Installation Considerations
For best results, Hansgrohe recommends that this unit be installed by a licensed, profes-
sional plumber.
Please read over these instructions thoroughly before beginning installation. Make sure
that you have all tools and supplies needed to complete the installation.
The mounting surface must be installed and made watertight prior to installation.
The rough must be installed prior to installation of this trim kit.
Some areas have plumbing codes limiting the maximum output temperature. The high
temperature limit stop may be reset to comply with these codes.
•
•
•
•
•
04130XX0
04134XX0
04131XX0

5
Install the valve trim
Push the escutcheon over the valve.
Install the handle. Tighten the screw with a
3 mm Allen wrench. The screw must
engage the slot on the cartridge.
Justify the handle.
Set the high temperature limit stop.
Push the spout sealing ring firmly into the spout
adapter (1).
Push the escutcheon and spout over the adapter
and sealing ring (2).
Tighten the screw using a 3 mm Allen wrench (3).
Do not over tighten the set screw.
Over tightening the screw may
damage the o-rings, which will
cause the spout to leak.
Install the spout
Remove the plug.
3
2
1
slot

6
Install the handshower
Pull the end of the handshower hose from the
holder.
Push the escutcheon over the end of the hose.
Push the elbow firmly over one end of the
handshower hose.
Tighten the hose nut.
Thread the hose down through the handshower
holder escutcheon and handshower holder.
Tighten the escutcheon over the handshower
holder.
Place the screen washer in the end of the elbow.
Connect the handshower to the elbow.
Lower the handshower and elbow into the holder.

7
Set the high temperature limit stop
Turn the water on to the tub spout or handshower.
Use a 3 mm Allen wrench to loosen the handle
screw. Remove the handle from the valve.
Carefully remove the retainer clip and the limit
stop ring.
Turn the temperature control stem until the water is
the desired high temperature, usually 110°F* .
Turn the stem clockwise to make the water
cooler, turn it counter-clockwise to make the water
warmer.
*Know and follow all applicble local plumbing codes when
setting the high temperature limit stop.
In Massachusetts, the maximum output temperature can be no
higher than 112° F.

8
Justify the handle
Turn the water on to the tub spout or handshower.
Place a thermometer in the water stream. Turn
the temperature control knob until the output wa-
ter temperature is 100°F. Turn the water off.
Install the stop ring so that it is against the stop
-- you should not be able to turn the stem further
counter-clockwise. Install the retainer clip.
Install the handle. Tighten the screw. Justify the
handle.

9
Loosen the handle screw with a 3 mm Allen
wrench.
Remove the handle.
Hold the handle lever in one hand. With the
other hand, turn the temperature control knob
until the 100° mark is next to the indexing mark
on the handle.
Install the handle on the valve. Tighten the screw.

10
User Instructions - ThermoBalance valve
Turn the lever clockwise to send the water to one
function, counter-clockwise to send the water to
the second function. The center position is off.
Turn the temperature control knob clockwise to
make the water cooler.
Turn the knob counter-clockwise to make the water
warmer.
The knob will stop at the 100° position (the safety
stop). To override the stop, press the knob down
and continue turning it counter-clockwise.
User Instructions - handshower
Raindance E 100 3-Jet, Raindance S 100
3-Jet: Push the function lever to the desired spray
mode.
Croma C 100 3-Jet: turn the function ring to the
desired spray mode.
If the flow of water decreases,
remove and rinse the screen
washer.
The handshower uses the Quiclean™ self-cleaning system.
Rub across the spray channels with a finger or a sponge to
dislodge any scale deposits.
function
ring
function
lever
function 1
function 2