Harbor Freight Tools 90552 User manual

ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
CHRISTMAS TREE
7 Foot
®

SKU 90552 PAGE 2
SPECIFICATIONS
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
DESCRIPTION
7 Foot High PVC
Noble Fir Style
916 Hooked on Wire Branches
Cross Metal w/Thumb Screws (3)
23 Lbs.
ITEM
Dimensions
Style
Branches
Stand Style
Net Weight
1. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries.
2. KEEP CHILDREN AWAY DURING ASSEMBLY. Do not allow children to play with or
touch light bulbs (not included).
3. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it
will operate properly and perform its intended function. Check for damaged parts and
any other conditions that may affect its operation. Replace or repair damaged or worn
parts immediately.
4. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical
replacement parts.
5. WEAR SAFETY GOGGLES (Must comply with ANSI) at all times when assembling.
6. AVOID SHARP EDGES WHEN ASSEMBLING. Wire Branches can damage eyes or
puncture skin.
7. DO NOT ALLOW CHILDREN OR ANIMALS TO CLIMB UPON THIS PRODUCT. Place
in an area where tipping of Christmas Tree can be avoided.
8. AVOID PLACING NEAR FIREPLACE. Never place candles on or near the Christmas
Tree. This product is NOT fireproof. Always check for electrical shortages. If damaged,
do not plug the lights (not included) in an electrical outlet.
9. AVOID THE RISK OF ELECTRICAL SHOCK. Do not remove light bulbs from decorative
lights (not included) when unit is on. Remove the extension cord from the power source
before replacing any light bulbs.
10. DO NOT LEAVE THE LIGHTS (NOT INCLUDED) ON WHILE THE TREE IS
UNATTENDED. Never leave the lights (not included) on overnight.

SKU 90552 PAGE 3
ASSEMBLY INSTRUCTIONS
1. Remove the three tree sections of tree boughs (#1,#2, #3) and the Metal Stand (#6) from
the container. Each section has pre-assembled Branches. Each Section has a “trunk”
down the center with a hole and, or a peg. Place the Bottom Section (#3-“E, F, & G”) “trunk”
in the hole in the Tree Stand (#5) and tighten the three Thumb Screws (#4).
See Figure A & B.
3. When each section is connected at the “trunk”, adjust Thumb Screws (#4) until the tree
stands straight. When this is done, you can string a strand of decorative Christmas lights
on your tree (not included). Plug an extension cord (not included) into an electrical
connection and plug into a power source. See Figure A. READ Warnings on page 2.
4. Spread branches of the Christmas Tree down to form an attractive tree. It is now ready
to decorate with Christmas ornaments. Caution: Do not use candles on the tree.
5. When storing your Christmas Tree, unplug all electrical connections, remove ornaments
and lights, disconnect the Sections #1, #2, #3 and remove the Stand (#5). Bend the
hinged boughs of the tree limbs in close to the trunk for compact storage. Suggestion:
May be wrapped with plastic bubble-wrap for protection (not included).
#4
Thumb
Screws
#5
Stand
#3
Largest
Tree
Section
#3
#2
#1
Figure A Figure B
Trunk
2. Connect the Middle Section (#2-“C & D”) by placing the ”trunk” peg of that section into the
hole of the Bottom Section (#3-“E, F, & G”). Repeat this step with the Top Section (#1-“A & B”)
See Figure B.

PARTS LIST
1
2
3
4
5
SKU 90552 PAGE 4
MAINTENANCE
1. For better and safer performance, keep all parts of this product clean and dry.
2. Periodically check to see that all hardware is in place.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
PART # DESCRIPTION QTY
1
1
1
3
1
Top Section (“A & B”)
Middle Section (“C & D”)
Bottom Section (“E, F & G”)
Thumb Screws
Metal Stand
#1
#2
#3
#4
#5