Harman Stove Company HB 38 DV User manual

The Harman Built Serenity III
HB 38 DV
Installation & Operating Manual
“Ce manuel est disponible en Français sur demande”
7R
R1
SAFETY NOTICE
PLEASE READ THIS ENTIRE MANUALBEFORE YOUINSTALL ANDUSE YOURNEW ROOMHEATER. FAILURE TO
FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTYDAMAGE, BODILYINJURY, OR EVEN DEATH.
FOR USE INTHE U.S.AND CANADA. SUITABLE FOR INSTALLATIONINMOBILE HOMES
IF THIS HARMAN STOVE IS NOT PROPERLYINSTALLED,AHOUSEFIREMAYRESULT. FORYOURSAFETY,FOLLOW
INSTALLATIONDIRECTIONS.
CONTACT LOCAL BUILDING OR FIRE OFFICIALSABOUT RESTRICTIONSAND INSTALLATIONINSPECTION
REQUIREMENTSINYOUR AREA.
CONTACT YOUR LOCAL AUTHORITY (SUCHAS MUNICIPAL BUILDING DEPARTMENT, FIRE DEPARTMENT, FIRE
PREVENTIONBUREAU,ETC.) TODETERMINE THENEED FORAPERMIT.
CETTEGUIDE D'UTILISATIONEST DISPONIBLEENFRANCAIS.CHEZVOTRECONCESSIONNAIRE DEHARMANSTOVE
COMPANY.
SAVETHESEINSTRUCTIONS.
R8

2
WARNING: If theinformation inthis manualis notfollowed exactly,a fireor explosion
mayresult causing property damage, personalinjury or loss oflife.
FORYOURSAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
FORYOUR SAFETY: WHATTODOIFYOUSMELL GAS
• Do not try to light any appliance.
• Open windows.
• Extinguish any open flame.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified gas installer, service agency,
or the gas supplier.
A.
B.
C.

Table of Contents
Introduction 4
Safety Precautions 4
Operation 6
Specifications 8
Installation 12
ArchFace 15
VictorianFace 16
Venting 20
DamperSettings 24
ChangingtoLP 25
Log Placement 27
Option Installation
Thermostat 28
Remote Control 28
Remote Register Kit 29
Maintainence 35
Wiring Diagram 37
TroubleShooting 41
Warranty 46
Manufactured by The
Harman Stove Company
352 MountainHouseRd.
HalifaxPA 17032
M:PM65-FILES\MANUALS\HBF\hb38dvR6.p65

4
Introduction
The Harman Serenity III Direct Vent Gas Fire-
placeisalistedgas-fireddirectventroomfireplacetested
byIntertekTestingServices/WarnockHerseytoANSI
Z21.88-2002/ CSA2.33-M02. CAN-CGA-2.17-
M91.Theinstallation oftheSerenityIIIDirectVent Gas
Fireplacemustconform with localcodes,orin the ab-
sence of local codes, with National Fuel Gas Code,
ANSI Z223.1 — latest edition and CAN 1 B1-149.1
and .2Installation Code.
Alsoforuseinmobile(manufactured)homes after
homeissited.
Mobile(manufactured)homeinstallationsmust
adhere tocurrent editions of Title24CFR,part 3280,
or CSA Z240.4.
CAUTION:Thisappliance mustbe vented to the
outside.
InstallationandrepairoftheSerenityIIIDirectVent
Gas Fireplaceshouldbedonebyaqualifiedserviceper-
son.The applianceshould beinspected beforeuseand
atleastannually byaqualifiedserviceperson.Morefre-
quentcleaningmayberequiredduetoexcessivelintfrom
carpeting, bedding material, etc. It is imperative that
controlcompartments,burners,and circulatingairpas-
sagewaysoftheSerenityIIIbekeptclean.
WhenoperatingyourHarmanSerenityIIIGasFire-
place, respect basic safety standards. Read these in-
structionscarefully before youattempt to operatethe
fireplace.Failuretodo somayresultindamageto prop-
erty orpersonalinjuryand mayvoid theproduct war-
ranty.Consultwithyourlocalbuildingcodeagency and
insurancerepresentativebeforeyoubeginyourinstalla-
tionto ensurecompliancewithlocalcodes,includingthe
needforpermitsandfollow-upinspections.
Severalissuesmustbeaddressed whenselectinga
suitablelocationforyourSerenityIIIGasFireplace.Ob-
servingrequiredclearancesto combustiblematerials,the
proximityto asafe chimneyorventingsystem location,
andtheaccessibilityofthegasandelectricalsupplymust
allbe considered.In addition,selectingalocation that
takes advantageofthebuilding'snaturalairflowisalso
desirable tomaximizetheheatingeffectiveness ofthe
fireplace.Inmany cases,thisisacentrallocationwithin
thebuilding.
Due to high temperatures, the Serenity III
DirectVentGas Fireplaceshouldbelocated out
oftrafficandawayfromfurnitureanddraperies.
Children and adults should be alerted to the
hazardsofhighsurfacetemperaturesandshould
stayawaytoavoidburns orclothingignition.
Youngchildrenshould becarefullysupervised
whentheyareinthesameroomastheappliance.
Clothing or otherflammable materials should
notbe placed onor near the appliance.
Surveiller les enfants. Garder les vetements,
les meubles, lessence ou autres liquides a
vapeurinflammables linde lappareil.
This appliancemaybeinstalled inanaftermar-
ketpermanently located(mobile) home,wherenot
prohibited bylocalcodes.
Thisapplianceisonly forusewiththetype(s)
ofgasindicated ontheratingplate.Thisapplianceis
not convertible for use with other gases, unless a
certified kitis used.
Cet appareilpeutetreinstalledansun maison
prefabriquee(mobile)dejainstalleeademeuresiles
reglementslocauxlepermettent.
Cetappareildoitetreutiliseuniquement avec
lestypesdegasindiquessurlaplaquesignaletique.
Ne pas l utiliser avec d autres gas sauf si un kitde
conversion dertifieestinstalle.
Anysafetyscreenor guard removedfor servicing
anappliance must be replacedprior tooperating
theappliance.

When the blower is off the air
gate is in the open position
which allows air to flow freely
through the air chamber and
up throughtheheatexchanger.
Air Gate Open
Air Gate Closed
Whenthe bloweristurnedon,
the air pressure from the
blower forces the air gate to
seal the air chamber. This
forces all the air from the
blower to travel through the
heat exchanger producing
two to three times more air
than other brands of gas
fireplaces.
Blower Off
Blower On
Air Gate Blower System
Typically in gas fireplaces the blower (which
is usually an option) is placed to blow air up the
back of the firebox without any method to keep the
air pressure from being lost. This method allows air
to flow freely around the blower when the blower is
off but gives up a large percentage of the blowers
efficiency when it is on.
TheAir Gate Blower System gives you the best
of both worlds.
200% To 300%
More Air
IMPORTANTFEATURE
5

6
OPERATION
Operation
HOW TO LIGHT THE FIRE
1. STOP! Read the safety information on the
front cover.
2. If using the optional thermostat, set thermostat
to the lowest setting.
3. Turn off electric power to the appliance.
4. Turn the ON-OFF/THERMOSTAT switch to
the OFF position.
5. Push in the gas control knob slightly and turn it
clockwise to "OFF." NOTE: THE KNOB
CANNOT BE TURNED FROM "PILOT" TO
"OFF" UNLESS IT IS PUSHED IN SLIGHTLY.
DO NOT FORCE IT.
6. Wait five (5) minutes to clear out any gas. If
you then smell gas, STOP! Follow "B" in the
safety information on the front cover. If you
don't smell gas, go to the next step.
7. Set the High-Low Regulator to High by turning
it fully counterclockwise.
8. Press in the gas control knob slightly and turn
counterclockwise to "PILOT."
9. Find the pilot by looking through the round
opening on the left end of the center log.
10. Push the control knob fully down and hold.
Immediately push the red piezo ignitor button to
light the pilot. It is normal to have to push the
red button several times before the pilot ignites.
Continue to hold the control knob in for about
one (1) minute after the pilot is lit. Release the
knob and it will pop back up. Pilot should
remain lit. If it goes out, repeat steps 5 through
9.
•If the knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
•If the pilot will not stay lit after several tries,
turn the gas control knob to "OFF" and call your
service technician or gas supplier.
11. Turn the gas control knob counterclockwise to
"ON."
12. Place the ON-OFF/THERMOSTAT switch in
the ON position or in the THERMOSTAT
position if the optional thermostat is used.
13. Turn on the electric power to the heater.
14. Set the optional thermostat to the desired
Gas Control
High-Low
ON-OFF/
THERMOSTAT
Switch
Three Speed
Blower Switch
Piezo Ignitor
Button
Rear Burner
ON/OFF
Switch
PILOT

7
OPERATION
room temperature.
15. Set the High-Low Regulator to desired setting:
Turn fully counterclockwise for High and fully
clockwise for Low.
16. Press the rear burner switch to the “ON” or
“OFF” position as desired. This switch will
return to the center position after it is pressed.
This is normal as well as a faint click when
pressed. The main burner must be lit before the
rear burner will light. The rear burner may be
turned “ON” or “OFF” at any time.
NOTE: An odor, resulting from the initial heating
of new materials in your heater, is not unusual
during the first fire, and in most cases will
disappear after an hour or two.
HOW TO TURN OFF THE FIRE
1. If using optional thermostat, set thermostat to
the lowest position.
2. Turn off the electric power to the appliance.
3. Turn the ON-OFF/THERMOSTAT switch to
the OFF position.
4. Push in the gas control knob slightly and turn it
clockwise to “OFF.”
NOTE: The knob cannot be turned from “PILOT”
to “OFF” unless it is pushed in slightly. Do not
force it.
FLAME HEIGHT ADJUSTMENT
There are separate adjusters for the front and
rear burners. These adjusters can be accessed by
reaching to the left side of the control panel and to
thebackofthe unit.Turn theadjusters counterclock-
wise (up) to increase flame height and clockwise
(down) to decrease. See above left. Adjusting the
flames too high will cause them to have black tips
and causesooting.Sootingcan causethe glassto get
dirty.
PilotFlames
If pilot flames are less than shown at left, use
pilot adjuster shown on page 36, to increase flames,
Warning:Theunitand adjustermaybehot. Wear
gloves and armprotection ifmaking adjustments
while in operation
Rear Burner
Adjuster Front Burner
Adjuster
Bottom rear view of burner module.
Normal Flame pattern. Note: Flames will vary in height and
position depending on the placement and the amount of
ember wool.

8
SPECIFICATIONS
Accordion Heat
Exchanger
VentCollar
Brick
Blower
Battery
Pack Rear Burner
Switch Hi-Low Knob
On-Off-PilotKnob
Ignitor
Blower Speed Switch
On-Off- Thermostat
Switch
BurnerModule
Electrical Box
Glass Door
TopStandoffs
RATINGS NATURAL PROPANE NATURAL PROPANE
Input Rating (Btu/hr)(0-4500 ft.)(0-1375 m) 43500 43500 41500 41400
Min. Input Rating (Btu/hr)(0-4500 ft.)(0-1375 m) 23300 23800 22800 23400
Orifices (DMS)(front/rear)(0-4500 ft.)(0-1375 m) 31/51 52/59 32/51 52/60
Manifold Pressure (in w.c./kPa) 3.5/0.87 10.0/2.49 3.5/.087 10.0/2.49
Min. Manifold Pressure (in w.c./kPa) 1.7/0.42 6.3/1.6 1.7/0.42 6.3/1.55
Min. Inlet Pressure (in w.c./kPa) 5.0/1.25 11.0/2.74 5.0/1.25 11.0/2.74
Max. Output (Btu/hr)(0-4500 ft.)(0-1375 m) (Blower Off) 31500 32000 31000 31000
Max. Efficiency (Blower On) top vent 84.5%, rear vent 75%
Top Vent Rear Vent

9
SPECIFICATIONS
2. Clearance from top of ach to bottom of wood facing. 10 inches with optional arch hood
and 15 inches without arch hood
1
2
1. Clearance from top of glass to 7” mantel. 26 inches
Optional Arch Hood
This fireplace may be placed on a wood floor.
Hearth is not required in
front of the fireplace
MINIMUM CLEARANCES FROM COMBUSTIBLE CONSTRUCTION
Unit to floor 0 in.
Face to side wall 7 in.
Unit to top stand-offs 0 in.
Unit to side stand-offs 0 in.
Unit to rear stand-offs 0 in.
Top of Glass to 7” Mantel 26in.
Electrical Rating: 120 Volts, 60 Hs, >2.75 AMP
Must be
Noncombustible

10
SPECIFICATIONS
Rear Vent Corner
70”
Gas In
Elictrical
Hook-up
11”

11
SPECIFICATIONS
Corner
64”
Top Vent
Gas In
Elictrical
Hook-up

12
INSTALLATION
Only For Qualified Installers
Wonder Board
Wood Mantel
Tile
Arch Face
Drywall
Typical Tile Facing Sectional View
Installation Options
This section deals with basic installation of and
Arch face and a Victorian face. It does not describe
every possible way to install this fireplace. This is
why it is important to have a qualified installer do
the installation.
The Serenity III can be laid in stone, brick, or
other masonry products. For this purpose a special
template face ( part # 1-00-4238231 ) is available.
We also offer a line of Harman Built mantels,
mantel cabinets, and corner mantel cabinets.
Shown is theM2 MantelCabinet with marble
finish facing, raised marblefinish hearth and a
gold plated Arch face with Arch hood.

13
INSTALLATION
Only For Qualified Installers
Placement
Here are some of the things that will effect the
exact placement of the fireplace.
1. Top or rear flue
2. Arch face or mantle face.
Arch face - Must decide on mantel and front
facing material.
3. Raised hearth, flat hearth or raised with no
hearth.
4. One, two or no remote duct kits.
5. Thermostat position.
6. Gas line hook-up is on the right side.
7. Electrical hook-up is on the left side.
This appliance mustbe electricallyconnected and
groundedinaccordance withlocal codes or,inthe
absense oflocal codes, with the current edition of
NFPA 70-National Electric Code or CSA C22.1-
CanadianElectricalCode.
This unit shall not be installed on carpet, vinyl
tile, or combustible material other than wood

14
INSTALLATION
Only For Qualified Installers
Noncombustible
Noncombustible material such as Dura-rock must be used
as facing on thefront of the fireplace cabinet.
Ceramic tile, marble or other decorative noncombustible
material may be used in front of theDura-rock. The total
thicknes for all layers of facing material may not exceed
one inch.
A one inch space under the front edge of the fireplace
allows roomfor hearth material. Hearth material that is
thicker must be compensated for by raising the fireplace the
proper amount.
1 inch thick
Installing fireplace in a wall with an arch face, ceramic tile facing,
and a face mantel.

15
INSTALLATION
Only For Qualified Installers
Latch Handles
FaceHooks
Slots for face hooks
Slots for face latches
Installing The Arch Face
To install the arch face, place the hooks on the
bottom rear of the face into the hook slots on the
fireplace. Next with the top latches handles in the
horizontal position push the face against the fire-
place and swing the latches straight down causing
them to enter the top face slots.
Removing The Arch Face
To remove the face, unlatch the top latches, tilt
the top of the face away from the fireplace and lift
the face out of the bottom slots.

16
INSTALLATION
Only For Qualified Installers
Assembling the Victorian Face
1. Position the mantel face down on the floor.
2. Place the left piller over the two studs on the
left side of the mantel. Install two washers and
nuts and tighten.
3. Place the left side of the breast plate into the
slots on the left pillar.
4. Place the Left hinge pin of the top grill door
into the round hole in the pillar.
5. Place the left hinge pin of the bottom grill door
into the round hole in the bottom of the pillar.
6. Place the right pillar over the studs on the right
side of the mantel face while simultaneously
placing right ends of the doors and breast plate
into their slots on the right pillar. Some assis-
tance is helpful.
7. Install any decorative panels at this time.

17
INSTALLATION
Only For Qualified Installers
Installing Fireplace To use
Victorian Face
When installing the fireplace to use the Victo-
rian Face the unit must be positioned back 1/2 inch
farther than with an arch face. A special drywall
bracket must be used to allow the drywallto extend
down far enough so the face will cover the drywall.
1. Install drywall bracket on top of the stand-offs
with two screws.
2. Place the fireplace into the framed opening so
the two ends of the drywall bracket rest against
the framing. This will position the face of the
fireplace 1/2 inch back from the face of the
framing.
3. Nail or screw the drywall bracket fast to the
framing.
4. Install and finish drywall as desired. Drywall
shall not extend below the drywall bracket on
the top and not closer to the fireplace cabinet
than the vertical wood framing on the sides.
Drywall Bracket
Nails
Nails
Drywall Bracket Drywall
Victorion Face
Standoff Drywall in Place

18
INSTALLATION
Only For Qualified Installers
Sealing Angle
Mounting Holes
Mounting The Victorian Face
1. Place fiberglass rope in sealing angle with angle
mounting bolts loose.
2. Place the face on the fireplace starting at the
bottom.
3. Slide the face into place and install the four
bolts as shown at left.
4. Slide the sealing angle against the fireplace and
tighten the mounting bolts.
Note: The face will have a one inch space under it
for hearth material. This must be considered
when planning the installation.
Complete FaceMounted

19
INSTALLATION
Only For Qualified Installers
Burn Only the Fuel for which the Heater is
Equipped
The Serenity III Direct Vent will burn either
natural gas or propane, but requires a change over
kit forpropane. The labelon the burnersystem mod-
ule indicates the fuelfor which it is equipped.Asec-
ond label, (on the valve)also indicates the fueltype.
Making The Connection
The gas inlet is located on the bottom right side
of the fireplace. The inlet fitting is a 3/8" female
flare flexible pipe.
A separate gas shut-off valve and a 1/8" N.P.T.
pluggedtapping should be installedimmediately up-
stream of the connection to the appliance.
The Serenity III Direct Vent Gas Heater must
be disconnected from the gas supply piping during
any pressure testing of that system at pressures in
excess of 1/2 psig (3.5 kPa).
The Serenity III gas control valve must be in
the OFF position during any pressure testing of the
gas supply system at pressures equal to or less than
1/2 psig (3.5 kPa).
WARNING: To avoid pipe compounds from
enteringintothe gas train, applycompounds only
tomale pipe threads and do notapply compound
to the first two threads.
CAUTION: TESTALL JOINTS FOR LEAKS
BEFORE OPERATING.
Gas Pressure Requirements:
Correct gas pressure and the use of a properly
sized gas supply line are essential for the safe and
efficient performance of this appliance. Make sure
that the plumber or gas supplier checks the gas sup-
ply line and gas pressure at installation.
NOTE:Improper gaspressure can affect heater
performance, flame color, or cause pilot outage.
Natural Gas:
Maximum inlet pressure 7.0" w.c. (1.74 kPa)
Minimum inlet pressure 5.0" w.c. (1.25 kPa)
Gas manifold pressure 3.5" w.c. (0.87 kPa)
LPG Gas:
Maximum inlet pressure 13" w.c. (3.24 kPa)
Minimum inlet pressure 11" w.c. (2.74 kPa)
Gas manifold pressure 10" w.c. (2.49 kPa)
DO NOT USE THIS HEATER IF ANY PART
HAS BEEN UNDER WATER OR EXPOSED TO
MOISTURE CORROSION. IMMEDIATELY
CALLAQUALlFlED SERVICETECHNICIAN TO
INSPECT THE HEATER AND REPLACE ANY
PART OF THE CONTROL SYSTEM AND ANY
GAS CONTROL WHICH HAS BEEN UNDER
WATER.
Pipe Length Schedule 40 Pipe Tubing, Type L
(Feet) Inside Diameter Outside Diameter
N.G. L.P. N.G. L.P.
0-10 1/2" 3/8" 1/2" 3/8"
1.3 cm 1.0 cm 1.3 cm 1.0 cm
10-40 1/2" 1/2" 5/8" 1/2"
1.3 cm 1.3 cm 1.6 cm 1.3 cm
40-100 1/2" 1/2" 3/4" 1/2"
1.3 cm 1.3 cm 1.6 cm 1.3 cm
100-150 3/4" 1/2" 7/8" 3/4"
2.0 cm 1.3 cm 2.3 cm 2.0 cm
RECOMMENDED GASPIPE DIAMETER
NOTE: NEVERUSE PLASTIC PIPE. CHECK TO CONFIRM
WHETHER YOUR LOCALCODES ALLOW COPPER
TUBING OR GALVANIZED PIPE.

VENTING
Only For Qualified Installers
20
6-5/8 x 4 8” x 5” Description
n/a 1208 6” Pipe Length
908B 1208B 6” Pipe Length, Black
n/a 1207 9” Pipe Length
907B 1207B 9” Pipe Length, Black
906 1206 12” Pipe Length
906B 1206B 12” Pipe Length, Black
904 1204 24” Pipe Length
904B 1204B 24” Pipe Length, Black
903 1203 36” Pipe Length
903B 1203B 36” Pipe Length, Black
902 1202 48” Pipe Length
902B 1202B 48” Pipe Length, Black
n/a 1211 11” to 14-5/8” Pipe, Adjustable
911B 1211B 11” to 14-5/8” Pipe, Adjustable, Black
n/a 1217 17” to 24” Pipe, Adjustable
945 1245 45oElbow
945B 1245B 34oElbow, Black
990 1290 90oElbow
990B 1290B 90oElbow, Black
940 1240 Rnd Support Box/Wall Thimble Cover
941 1241 Cathedral Ceiling Support Box
943 1243 Flashing, 0/12 to 6/12 Roof Pitch
943S 1243S Flashing, 7/12 to 12/12 Roof Pitch
953 1253 Storm Collar
963 1263 Ceiling Firestop
988 1288 Wall Strap
981 1281 Snorkel Termination (36”)
982 1282 Snorkel Termination (14”)
984 1284 Horizontal Square Termination
980 1280 Vertical Termination
991 1291 Vertical Termination, High Wind
950 1250 Vinyl Siding Standoff
1222D (Only available from Harman) 8” x 5” to 6 5/8” x 4” Adaptor
PartNumbers for SimpsonDura-Vent Pipe and Fittings
Use Only Approved Venting
This appliance has been tested and is listed for installation with Simpson Duravent GS venting com-
ponents. The Simpson Duravent GS warranty will be voided, and serious fire, health, or other safety
hazards may result from any of the following actions:
• Installation of any damaged Duravent GS component.
• Unauthorized modification of the Duravent GS System.
• Installation of any component part not manufactured or approved by Simpson Duravent.
• Installation other than as instructed by Simpson Duravent and the appliance manufacturer.
Consult your local building codes before beginning the installation, and follow the manufacturer's
instructions exactly. The Simpson Duravent GS venting components listed below are approved for use
with the Serenity Direct Vent Gas Fireplace.