Harmony Collection LTM-3L-22 Series User manual

3MOTOR ELECTRIC HEIGHT ADJUSTABLE TABLE
LTM-3L-22-x x / EL
Assembly and instructions

1
Please read this document carefully.
If this desk is sold, please provide this manual to the buyer.
Use - Liability
This height adjustable desk has electric motors and is designed for use in dry work areas only. The desk
height is adjustable so that it can be positioned at the most ergonomically suitable height. Any other use is
at user’s risk. Under no circumstances does the manufacturer accept warranty or liability claims for damag-
es caused from improper use or handling of the desk frame.
Make sure no obstacles are in the desk’s path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to accommodate the change in height.
Children should only operate desk under adult supervision.
There is a risk of injury and electric shock if not properly installed.
Keep liquids away from electrical components.
Do not sit or stand on the desk frame.
Do not crawl or lie under the desk frame.
Do not place any object taller than 508mm (20”) underneath the desk .
Do not open any of the electrical components. There is a danger of electric shock.
This product is designed with a duty cycle of 10% (5min. on, 20 min. o).
In the event of a power outage or if the power cord is unplugged, a manual reset may be necessary (View step
7).
1-
2-
3-
4-
5-
6-
7-
8-
9-
10-
11-
12-
13-
Caution!

2
Power Cord
Control switch
37x
18x
Control Box
Cables
Parts Included
Frame
HardwareElectrical components
Please note that C & D as well as E & F are
preassembled.
5mm
1x
16x (Preassembled)
g
g
g
h
h
h
i
i
i
g
h
i
Table 1 Table 2
4x 2x
2x 1x
2x 1x
2x
2x
2x
2x
1x
1x
*2x extra holes

3
Assembly instructions
Step 1
Choose the desired table conguration.
Step 2
Parts C & D, E & F are preassembled. You must adjust them to
approximately match the length of your table. Do not tighten the
screws completely before the nal adjustments.

Step 4
Étape - Step 4
4
Complete this step for both legs.
10x
Add the side for the return.
2x
g
c
dg
Table 1
Step 3
Table 2
e
f

Add the last ‘‘G’’ post to the return side.
Step 5
Install the end supports. WARNING: The longer one ‘‘A’’ goes on the primary side (Table 1), and the shorter one ‘‘B’’ goes on
the side of the return (Table 2).
Step 6
5
g
4x
8x
Table 2
a
b

Step 7
6
Install the feet as well as the adjustable glides.
6x 12x
Step 8
We recommend to secure the wood panels together with
brackets (not included). Center the supports on the panels.
Adjust the lengths of the center supports.
Please center the supports for best results.
h

Step 10
7
Install the controller so it does not exceed the table top. In the
event of a power outage or if the power cord is unplugged, a
manual reset may be necessary. See Step 9 for details.
To Preset Heights:
Choose a comfortable height. Press the “M” button and choose which
number you want to associate this height with. Repeat the sequence
for the other desired heights.
4 personal height settings.
Height setting control button.
Up-down.
Step 9 14x
Install the panels on the structure.
2x

8
Step 11
Install the control box next to the right leg. Make sure that the outlets are facing the left leg. When puting the table on it’s leg,
please ask a second person to help you. Make sure that the wires will not obstruct the movement of the table.
Power Cord
3x Cables
Control switch.
Control Box