Universal Furniture EXPLORE HOME BACALL 847220 User manual

INSTRUCTION SHEET
847220/22FR/212W
847210/21FR/212W
BACALL BED
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Headboard
1PC
B
Bed wall panel
2PCS
C
Side rail
2PCS
D
Footboard
1PC
E
Slat panel
2PCS
F
Center support
4PCS
G
Wall Pad
2PCS
H
Metal salt
1PCS
I
Metal rail
1PCS

INSTRUCTION SHEET
847220/22FR/212W
847210/21FR/212W
BACALL BED
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Put the all parts on a soft and smooth surface to avoid damage or being scratched. .Attach
the metal rail (I) to the metal slat (H) with nuts (11), flat washers (12) and bolts (13) using
wrench (15).
Step 3: Assemble side rails (C) with headboard (A) using bolts (1), curved washers (2), spring
washers (3) and nuts (4). Tighten them by wrench (6).
Step 4: Attach the metal slat (H) to side rail (C)with flat washer(12),Bolt (14) using wrench(15).
Step5: Attach the footboard (D) to the side rail(C) with bolts (1), curved washers (2), spring washers
(3) and nuts (4). Tighten them by wrench (6).
Step 6: Attach the footboard (D) to the metal rail(I) with flat washer (12),Bolt (14) using wrench(15).
Step 7: Screw center supports (F) into slat panels (E).Put slat panels (E) onto the inside notches of
side rails (C), tighten them with screws (5) by screwdriver (not provided).
Step 8: Assemble bed wall panel (B) to headboard (A) using mending plate (7), flat washers (12),
bolt (13). Tighten them by wrench(10). Screw wall pad (G) into headboard back and bed wall
panel back .
Note: 847210/21FR/212W bed has 2pcs center support.
Assembly is now complete.

INSTRUCTION SHEET
847220/22FR/212W
847210/21FR/212W
BACALL BED

INSTRUCTION SHEET
847220/22FR/212W
847210/21FR/212W
BACALL BED