Hartke 2.5xl User manual

2 x10″ Plus 5” Stackable
Aluminum Drive Bass Enclosure
Hartke

2.5XL Introduction and Features
Congratulations on purchasing the 2.5XL bass enclosure by Hartke! The XL
Series enclosures have been designed to provide excellent tone with a fast
attack, deep low-end and punchy output. The 2.5XL Features two 10”, propri-
etary low frequency drivers with specially designed aluminum cones, large voice
coils on Kapton formers, impregnated fabric surrounds, and matched convex
dust covers all mounted in a heavy-duty steel frames. Rounding out the tone is
a proprietary 5” aluminum mid-range driver. Using heavy-duty plywood con-
struction, covered in rugged carpet with recessed jack plate and ergonomic
metal handles, the 2.5XL will provide reliable performance from gig to gig and
venue to venue.
In these pages, you’ll find a detailed description of the features of the 2.5XL , as
well as a description of its front and rear panels, step-by-step instructions for its
setup and use and full specifications. You’ll also find a warranty card enclosed—
please don’t forget to fill it out and mail it in so that you can receive online tech-
nical support and so we can send you updated information about these and
other Samson products in the future.
We recommend you record your serial number in the space provided below for
future reference.
Serial number:
Date of purchase:
Should your unit ever require servicing, a Return Authorization number (RA)
must be obtained before shipping your unit to Samson. Without this number, the
unit will not be accepted. Please call Samson at 1-800-3SAMSON (1-800-372-
6766) for a Return Authorization number prior to shipping your unit. Please
retain the original packing materials and if possible, return the unit in the origi-
nal carton and packing materials.
210 XL Features
•2x 10 Inch heavy-duty Aluminum
Low Frequency drivers
•Special Design 5-inch Aluminum
Mid to High-range driver
•3/4" Plywood construction
•Tuned front shelf port
•Perforated metal speaker grill
•Recessed metal handles
•Stacking corners
•Dual, parallel wired 1/4" jacks
•Covered in durable carpet

About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little about
impedance. Impedance is the electronic load that the speaker puts on the power amplifier
and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers, of equal impedance
are wired in "Parallel", the total imped-
ance is cut in half and when two speak-
ers are wire in “Series”, the total imped-
ance is the sum of the speakers individ-
ual impedance.
The 2.5XL impedance is 8 Ohms. So,
when two 2.5XL’s are connected
together in parallel, the total impedance
is 4 Ohms. The impedance of your
speaker also has an effect on your
amplifier. In general, the lower the
impedance, the more power your ampli-
fier will put out.
IMPORTANT: There is a minimum safe
impedance so be sure to check the
manufacturer’s recommended imped-
ance for your amplifier to avoid any
damage to your amplifier or voiding
your warranty.
Connecting the 2.5XL to Your Amplifier
The 2.5XL connections are made via
1/4” phone jacks located on the rear
panel jack-plate. Be sure to make your
connection with un-shielded speaker
cable. Connect the Amplifier Output to
the speaker Input on the 2.5XL’s rear
jackplate.
Using the EXTENSION Output
The 2.5XL provides a convenient
Extension Output for connecting addi-
tional speaker cabinets in parallel. Be
sure to read the section above on
impedance to insure a proper hook up
with your amplifier. Follow the steps
below to connect two 2.5XL’s using the
Extension Output. Connect the
Amplifier Output to the Input of the first
2.5XL. Now, connect the Extension
Output to the Input of the second
2.5XL.
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
MODEL 2000
200 WATTS
8 = 120 WATTS
4 = 200 WATTS
CAUTION
TOPREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.TO PREVENT FIRE OR SHOCK
HAZARD,DO NOT EXPOSE TO RAIN OR MOISTURE.
ASSEMBLEDIN R.O.K.
SERIALNUMBER
115
~AC INPUT
115V/230V50/60Hz
FUSE
5A/250V,180W (115V)
2.5A/250V,450W (230V)
SPEAKER OUTPUTS
8
8
ONOFF
HPF
EFFECT
SEND
RETUIRN
2.5XL BASS CABINET
200 WATTS
Hartke
8 EXTENSION
INPUTS
MADEINCHINA
SERIALNUMBER
HartkeSystems Distributed worldwide by SamsonTechnologies
www.hartke.com
8
Connecting the 2.5XL
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
MODEL 2000
200 WATTS
8 = 120 WATTS
4 = 200 WATTS
CAUTION
TOPREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.TO PREVENT FIRE OR SHOCK
HAZARD,DO NOT EXPOSE TO RAIN OR MOISTURE.
ASSEMBLEDIN R.O.K.
SERIALNUMBER
115
~AC INPUT
115V/230V50/60Hz
FUSE
5A/250V,180W (115V)
2.5A/250V,450W (230V)
SPEAKER OUTPUTS
8
8
ONOFF
HPF
EFFECT
SEND
RETUIRN
2.5XL BASS CABINET
200 WATTS
Hartke
8 EXTENSION
INPUTS
MADEINCHINA
SERIALNUMBER
HartkeSystems Distributed worldwide by SamsonTechnologies
www.hartke.com
2.5XL BASS CABINET
200 WATTS
Hartke
8 EXTENSION
INPUTS
MADEINCHINA
SERIALNUMBER
HartkeSystems Distributed worldwide by SamsonTechnologies
www.hartke.com
8

Hartke 2.5XL Specifications
Type Tuned, Vented Enclosure
Impedance (Ohms) 8 Ohms Impedance
Power Handling 200 Watts RMSPower Handling
Drivers 1 - Hartke 5XL8 and 2 - 10XL16
Special Design Aluminum 10",
16 ohm,100 watt drive units
SPL 99dB @ 1W/1M
Frequency Response 35Hz - 12kHz
Inputs Parallel 1/4”
Weight 66 lbs. (29.94 kg)
Dimensions Height:18" (45.72 cm)
Width: 24" (60.96 cm)
Depth: 18" (45.72 cm)
Specifications
Distributed Worldwide Exclusively by:
Samson Technologies Corp.
575 Underhill Blvd.
P.O. Box 9031
Syosset, NY 11791-9031
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: [phone]
www.samsontech.com
Hartke