Haul-All Equipment Sure Flame FN42 User manual

FN42
AIR MOVER
Effective: Feb 26, 2013
3
13
15
20
17
16
2
18
1
14
16
17
13
12
2
4
19
3
5
8
6
910
11
7
FN42C Air Mover Parts
www.sureflame.com





Bearing Insert
Ref. Part No. Description
2 6706
9
10
6
7
8
4
5
3
FN20-76
5954
FN42-1901
5960
5983
9262
5961
5958
1 5932
1HP Motor
Pillow Block
20A Toggle Switch
Switch Box
Fan Sheave
Motor Sheave
46" V Belt
Shaft
42" Fan Blade
Ref. Part No. Description
Switch Cover
Fan Guard
Fan Housing
Tubular Frame
Bushing
FN42-702
FN42-511
FN42-709
19
20 9412
16
17
18
13
14
15
6119
6330
5959
5990
Pull Pin
FN20-14
WRS-108
11
12 72" Power Cord
8" Semi Pneumatic Wheel
1/2" Push Nut
Tubing Insert
21
5508
21 Strain Relief
Effective: Feb 26, 2013
3
13
15
20
17
16
2
18
1
14
16
17
13
12
2
4
19
3
5
8
6
910
11
7
FN42C Air Mover Parts
www.sureflame.com




Bearing Insert
Ref. Part No. Description
2 6706
9
10
6
7
8
4
5
3
FN20-76
5954
FN42-1901
5960
5983
9262
5961
5958
1 5932
1HP Motor
Pillow Block
20A Toggle Switch
Switch Box
Fan Sheave
Motor Sheave
46" V Belt
Shaft
42" Fan Blade
Ref. Part No. Description
Switch Cover
Fan Guard
Fan Housing
Tubular Frame
Bushing
FN42-702
FN42-511
FN42-709
19
20 9412
16
17
18
13
14
15
6119
6330
5959
5990
Pull Pin
FN20-14
WRS-108
11
12 72" Power Cord
8" Semi Pneumatic Wheel
1/2" Push Nut
Tubing Insert
21
5508
21 Strain Relief
SPECIFICATIONS
Electrical rating 1 HP 115 volts, 60 Hz, 9 Amp single phase
Fan rating: 14000 CFM. 42” 27° Fan blade
Weight 210 lbs
August 1, 2020, Rev: 1
SERVICE AND MAINTENANCE MANUAL
PLEASE RETAIN FOR FUTURE REFERENCE
SURE FLAME PRODUCTS
A DIVISION OF HAUL-ALL EQUIPMENT LTD.
4115 - 18 Avenue North
Lethbridge, Alberta T1H5G1
www.sureame.ca

Troubleshooting Chart
Fan motor does not start
Fan not plugged in to active power source
Check connection/ power source
Cord is damaged
Check power cord
Faulty motor
Replace motor
Toggle switch failure
Replace switch
Motor starts but airflow is not sufficient
Plugged inlet/outlet
Clean fan guard(s)
Obstacles in the way
Make sure area around fan is clear
Deformed/damaged fan blade
Replace fan blade
Particulate build up on fan blade
Clean fan blade. Replace if not possible
Duct installed on fan
Remove duct. Fan is not designed for ducts
Fan blade loose on shaft
Tighten set screw
Belt slipping
Tighten belt by moving the motor
Wrong sheaves installed
Ensure that the correct sheaves are installed
Motor starts but with excessive vibration/noise
Faulty motor/motor bearings/Shaft bearings
Replace motor/ Replace enclosed bearings
Damaged fan blade
Replace fan blade
Particulate build up on fan blade
Clean fan blade. Replace if not possible
Fan blade loose on shaft
Make sure set screws are tight
Motor starts but shuts down due to overload
Faulty motor
Replace motor
Extension cable too long or too low gauge
Use shorter thicker extension cables
Wrong sheaves installed or switched around
Install correct sheaves and ensure their
correct placement
FN42 AIR MOVER
Failure to comply with the precautions and instructions
provided with this air mover, can result in death, serious
bodily injury and property loss or damage from hazards
of re, explosion, impact, and/or electrical shock.
Only persons who can understand and follow the
instructions should use or service this air mover.
If you need assistance or information such as
an instruction manual, labels, etc., contact the
manufacturer.
Never use the air mover in spaces which may contain
volatile or airborne combustibles, or products such as
gasoline. Do not operate the air mover without the fan
guards.
WARNING
GENERAL HAZARD WARNING
Installation and operation
•To prevent risk of electrical short, only use this product on GFCI (Ground
Fault Circuit Interrupter) protected circuits.
•Ensure the fan is in good condition before operating. Check for damaged
or missing parts.
•Place on a at stable surface to avoid tipping over.
•Allow for at least 2 feet of clearance on the intake and output from obstacles.
•Connect the fan to an appropriate power source and turn the switch on.
•Do not move unit while in operation. Disconnect from power before doing so.
•This unit is not designed for ducting. Manufacturer is not responsible for
ducted performance.
•This unit is not intended for outdoor use or storage. Doing so may void
warranty.