STEP 10 - ATTACHING ULTRA-STAIR UNIT
TheBil-JaxUltra-StairUnitscomeinarangeofsizesthatcanadjusttostageheightsof12”to70”.
A) TheUltra-StairUnitrequiresanadapterwhenusedwithAS2100stages.Aachadapter
byinserng3/8”x1”boltwithlockwasherthroughslotinadapterandintothreaded
block on stair mount plate.
B) Screwinfootpadsinboomoflowerstep.
C) Ifstageheightisover3’,insert1-3/4”sq.legintothetwosocketsofthestairadapter
andaachwith2-3/8”snappinforextrasupport.
D) Setthelowerlipofthetwoadapterlocksinsidethestagedeckchannelalongthe
perimeterofthestagedecks.
E) Insert5/16”T-Handlehexwrenchinboltheadinthetopofthestairadapterandrotate
sotheT-Lockclampstheadaptertothestage.
F) Lowerthestairssothefootpadstouchtheground.Adjustfootpadssotheheightof
boomstepmatchesriseofothersteps.
G) Tightenwingnutonsloedlockbaroneachsideofstairs.
H) Oneachsideofstairs,rotatethreadedlockbarperpendiculartostairstringertubes.
Rotatewingnutsothatthesaddleweldmentispressedghtagainstupperstringertube.
I) Inserthandrailpostintostepsocket.Aachwithwasher,3/8”x2”boltandlocknut.
Repeat for all four posts.
J) Placehandrailsoitstraddlespost.Aachwith3/8”x2-1/4”boltandlocknut.Repeat
oneachendforallfourhandrails.
! WARNING ! – Failure to correctly install stairs could result in serious injury or death. Verify that
each T-Lock is fully seated inside the stage deck channel and locked in place. Also verify that all nuts
on lock bars are ghtened.
9
G H I
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOW ING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
J
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
A CB D E
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
STEP 10A STEP 10B STEP 10D
1/4 SCALE
STEP 10E
1/4 SCALE
STEP 10G
1/4 SCALE
STEP 10H
1/4 SCALE
STEP 10I
1/4 SCALE
STEP 10J
1/4 SCALE
1/4 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO.DATE
DR
BY
REV
BY SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:8
FINISH
lbs.
WEIGHT
10-22-19
ELB
STEP 10
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT C2017
