Hayter Motif 48 Autodrive User manual

Motif 48 Autodrive
Code 439
Original Version (EN)
Issued: 21.01.14 From Serial Number: 314000001 onwards Part number: 3383-440 Rev A

CONTENTS
2
Introduction 3
Main Features / Specifications 4
Safety Precautions 5 - 6
Training 5
Preparation 5
Safety Symbols 5
Operation 5 - 6
Maintenance & Storage 6
Control Symbols 6
Assembling the Mower Before First Use 7
Delivery Checklist 7
Handlebar 7
Grassbag Attachment 7
Prevent Engine Damage 7
Oil Type 7
Check Oil Level 7
Fuel Type 7
Operating the Mower 8 - 10
Controls 8
Before Mowing 8
Starting 8
Forward Travel 8
Reverse Travel 8
Turning 8
Stopping 8
Slopes 8
Height of Cut 9
Grassbag 9
Collection Without Grassbag 9
Heavy Growth 9
Non Grassed Areas 9
Maintenance Schedule 10
Engine Detail 10
Mower Maintenance 11 - 13
Carburettor Adjustments 11
Oil Service 11
Air Cleaner Service 11
Spark Plug Service 11
Keeping Engine Clean 11
Grassbag 11
Deck Housing 12
Securing Nuts and Bolts 12
Clutch Cable Adjustment 12
Lubrication 12
Cutterblade Removal 12
Cutterblade Assembly 12
Cutterblade Sharpening 13
Storage 13
Lawn Care Calendar 14
Trouble Shooting 15
Warranty 16
EU Privacy Statement 17
Notes 17 - 19
Service Records & Customer Information 20

INTRODUCTION
3
Thank you for purchasing a Hayter mower. The following pages are designed to help you gain safe
and efficient service from your machine.
IMPORTANT: This ‘Owners Handbook’ should be regarded as part of the mower as it gives
essential information regarding mower safety, operation, maintenance and specifications. Read
and understand this handbook prior to operating your mower for the first time. Make sure you are
familiar with all the controls and points of regular maintenance. If you have any doubts, consult
your local Hayter authorised dealer who will be pleased to give you assistance.
IMPORTANT: This mower is designed solely for use in a domestic grass cutting environment.
Use in any other way is considered as contrary to the intended use. Compliance with and strict
adherence to the conditions of operation, service and repair as specified in this handbook also
constitute essential elements of the intended use.
This mower should be operated, serviced and repaired only by persons who are familiar with its
particular characteristics and who are acquainted with the relevant safety procedures.
The safety precautions listed in this handbook and all other generally recognised regulations on
safety must be observed at all times.
Use of non standard parts or any arbitrary modifications carried out on this machine may relieve
Hayter Limited of liability for any resulting damage or injury.
Hayter mowers are robustly constructed and designed for efficient economical performance under
normal mowing conditions. Correct operation and maintenance will ensure a long and satisfactory
service life. Prior to despatch from our factory every effort is made to ensure that your mower is
delivered in perfect condition.
Throughout this handbook all references to left and right are as viewed from behind the handlebar,
in the direction of forward travel.
This handbook is based on information available at the time of publication.
HAYTER LIMITED reserve the right to amend product specifications without prior notification.
Please be advised that the illustrations in this Handbook are generic and not specific to your
product.
For a full range of products and to locate your nearest authorised sales stockist, service or parts dealer please visit our website at www.hayter.co.uk

4
MAIN FEATURES SPECIFICATIONS
1. Spark Plug Lead 9. Engine Start Grip
2. Exhaust 10. Engine Stop Lever
3. Exhaust Guard 11. Handlebar
4. Oil Filler Cap and Dipstick 12. Ground Drive Clutch Lever
5. Height of Cut Adjuster 13. Grassbag Assembly
6. Rear Deflector 14. Serial Number Label
7. Handlebar Securing Knob 15. Fuel Filler Cap
8. Rope Guide 16. Carburettor
17. Air Filter
Code 439
Weight 32.7 Kg
Length 1415 mm
Width 530 mm
Height 1030 mm
Width of Cut 480 mm
Height of Cut (8 positions) 25 - 55 mm
Cutterblade Speed 2800 rpm
Engine Briggs & Stratton
Engine Type Series 600EX
Fuel Type Unleaded petrol
Fuel Capacity 0.8 litres
Oil Type SAE 30
Oil Sump Capacity 0.47 litres
7
13
14
15
16
8
9
10
11 12
17
1
2
3
4
6
5

SAFETY PRECAUTIONS
5
Safety Symbols
Safety Alert Symbol
This safety alert symbol indicates important safety
messages. When you see this symbol be alert to the
possibility of injury. Carefully read the following and
inform others.
Your mower is perfectly safe if used correctly. Failure to
observe the following precautions may result in serious
injury.
Training
Before using the mower read the owners handbook carefully.
Pay particular attention to the safety precautions. Ensure
that you are familiar with the controls and the proper use of
the equipment. Learn how to stop the mower quickly in an
emergency.
Never allow children or people unfamiliar with these
instructions to use the mower. Local regulations can restrict
the age of the operator.
Never mow while people, especially children, or pets are
nearby.
Keep in mind that the user is responsible for accidents or
hazards occurring to other people or their property.
Preparation
While mowing, always wear substantial footwear and long
trousers. Do not operate the equipment when barefoot or
wearing sandals.
Thoroughly inspect the area where the mower is to be used and
remove all objects which may be thrown by the machine.
WARNING: Petrol is highly flammable.
• Store fuel in containers specifically designed for this
purpose.
• Refuel outdoors only and do not smoke while refuelling.
• Add fuel before starting the engine. Never remove the cap
of the fuel tank or add petrol while the engine is running
or when the engine is hot.
• If petrol is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until the petrol
vapours have dissipated.
• Replace all fuel tank and container caps securely.
Replace faulty silencers.
A damaged cutterblade or loose fixing bolt are major hazards.
Before use, always visually inspect the cutting mechanism to
ensure that it is in good condition.Adamaged cutterblade must
be replaced immediately with a genuine Hayter replacement
part.
Operation
Do not operate the engine in a confined space where exhaust
fumes (carbon monoxide) can collect.
Always pull the starter cord slowly until resistance is felt and
then pull the cord rapidly. This will avoid kickback and prevent
hand or arm injury.
Mow only in daylight or good artificial light.
Avoid using the machine on wet grass, where feasible.
Always be sure of your footing on slopes.
Walk, never run.
Do not mow excessively steep slopes of more than 20° and
mow across the face of slopes, never up and down.
Exercise extreme caution when changing direction.
Safety Alert Be Aware To
The Possibility Of Injury. Carefully Read The Owners Handbook Before Using The Machine Danger Of Severing Toes Or Fingers In Cutting Mechanism Danger Of Being Hit By Thrown Objects Keep Bystanders At A Safe Distance From The Mower Stop Engine And Remove The Spark Plug Lead Before Working On The
Mower.

SAFETY PRECAUTIONS
6
Control Symbols
STOP
Engine Stop Height of Cut Adjustment
Operation cont
Use extreme caution when reversing or pulling the mower
towards you.
Always replace worn or faulty parts with genuine Hayter parts.
This machine contains spring loaded assemblies which
could cause a hazard when disassembled and reassembled.
Maintenance should only be carried out by a Hayter authorised
dealer.
Always ensure the blade has stopped by releasing the engine
stop lever, before tilting the mower for transportation or
crossing surfaces other than grass.
Never operate the machine with defective guards, or with out
safety devices, for example deflectors and/or grass bag in place.
Do not change the engine governor settings or overspeed the
engine.
Start the engine carefully, with feet well away from the
cutterblade before starting the engine.
Do not tilt the mower when starting the engine.
Do not start the engine when standing in front of the discharge
chute.
Do not put hands or feet near or under rotating parts.
Never pick up, carry the machine or lift the rear deflector while
the engine is running.
Never touch the exhaust/exhaust guard or cooling fins when
the engine is hot.
Stop the engine and disconnect the spark plug lead:
• Before clearing blockages or unclogging the discharge
chute.
• Before cleaning/checking or working on the machine.
• After striking a foreign object. Inspect the machine for
damage and ensure necessary repairs are made before
restarting and operating.
• If the machine starts to vibrate abnormally, check
immediately.
Stop the engine:
• Whenever you leave the mower;
• Before refuelling.
Maintenance & Storage
Keep all nuts, bolts and screws tight to ensure that the
equipment is in safe operating condition.
Frequently check fuel lines and fittings for cracks or leaks and
replace if necessary.
Check the rear deflector and grassbag frequently for wear or
deterioration.
Replace worn or damaged parts for safety.
Wear strong work gloves when removing and reassembling the
cutterblade.
Inspect the exhaust periodically and replace if worn or leaking.
Never store the mower with petrol in the tank within an
enclosed area where fumes may reach an open flame or spark.
Allow the engine to cool before storing in any enclosure.
To reduce the fire hazard, keep the engine and the surrounding
deck area free of grass, leaves or excessive grease.
If the fuel tank has to be drained, this should be done outdoors
and when the engine is cool.

ASSEMBLING THE MOWER BEFORE FIRST USE
7
Delivery Checklist
Remove the mower from the packaging and check that the
following items have been supplied correctly. If any items are
missing, contact your local Hayter dealer.
1. Engine Handbook
2. Grassbag Assembly
3. Parts List & DOC
To prevent accidents cut off the long ribbon attached to the
grassbag and discard.
(Refer fig.1)
Handlebar
Unscrew the handlebar securing knobs sufficiently to allow the
handlebar to pivot. Hold the engine stop lever in towards the
handlebar and unfold the handlebar to the operating position.
Tighten both handlebar knobs to secure in position.
(Refer fig.2)
Take care to ensure that the control cables do not become
snagged at the pivot point.
Grassbag Attachment
Raise the rear deflector, lower the grassbag and hook into
position. Lower the deflector to rest on the grassbag.
(Refer fig.3)
Prevent Engine Damage
To prevent engine damage the engine is shipped without oil
or petrol. The engine must be filled with the correct grade
of oil and petrol before starting.
Oil Type
Always use high quality detergent oil classified SAE 30 oil.
Never use additives with recommended oil.
To prolong the life of your engine it is important that the oil is
changed after the first 5 hours of use - Refer to ‘Maintenance
Schedule’.
Check Oil Level
Clean around the oil filler cap before removing. With the
mower on a level surface, unscrew and remove the oil filler
dipstick. Wipe oil from it with a clean cloth. Screw the oil filler
dipstick back in place, then unscrew and remove it to check
the oil level.
(Refer fig.4 & 5)
The oil level is correct when it is at the full mark on the
dipstick. DO NOT OVERFILL.
(Refer fig.5)
Fuel Type
Always use clean, fresh unleaded petrol. Purchase fuel in
quantities that can be used within 30 days. Never mix oil
with petrol. For added engine protection Briggs & Stratton
recommend the use of their fuel additive which is available
from an authorised Briggs & Stratton service dealer.
Fill to base of neck to allow for fuel expansion. Do not
overfill the fuel tank.
(Refer fig.6)
Fig. 1 Fig. 2 Fig. 3
ADD FULL
0.15
Litres
Fig. 5
O
I
L
Fig. 4 Fig. 6

OPERATING THE MOWER
8
Controls
Operate all control levers several times and ensure that the
cables move freely. Check that the engine stop lever returns
freely to its rest position when released.
(Refer fig.7)
Before Mowing
To prevent accidents, thoroughly inspect the area and
remove all objects which when contacted by the mower
cutterblade could become dangerous projectiles. Inspect
the area for hidden obstructions which when contacted
by the cutterblade could risk health and safety or result
in damage to the mower. Remember the location of these
obstructions and ensure that you mow around them.
(Refer fig.8)
Starting
Stand behind the mower and hold the handlebar together with
the engine stop lever with your left hand. With your right hand
hold the engine start grip and pull slowly until resistance is felt,
then pull rapidly to crank the engine. Carefully return the start
grip to the storage position when the engine starts.
(Refer fig.9)
If the engine does not start after 5 attempts - Refer to “Trouble
Shooting”.
The engine stop lever must be held firmly against the handlebar
to start and keep the engine running. If the engine stop lever is
released the engine will stop.
To prevent damage never pull the engine start grip when
the engine is running.
Forward Travel
Hold the handlebar and operate the ground drive clutch lever to
power the mower forward.
When the ground drive clutch lever is disengaged, the mower
may be pushed. This feature is useful when mowing in confined
areas.
(Refer fig.9)
Reverse Travel
Hold and pull against the handlebar with both hands to reverse
the mower.
(Refer fig.10)
Turning
To make a tight turn, release the ground drive clutch lever.
Apply downward pressure on the handlebar to raise the front
wheels just above ground level and steer in the required
direction.
To prevent accidents do not raise the front of the mower
excessively when making a turn. Never raise the rear of the
mower when the engine is running.
Stopping
Release the engine stop lever and then the ground drive clutch
lever.
Emergency stop: As above. If the engine fails to stop
disconnect the spark plug lead.
(Refer fig.11)
Slopes
To prevent engine damage do not use the mower on slopes
greater than 20 degrees.
(Refer fig.12)
20
Fig. 7 Fig. 8 Fig. 9 Fig. 11
Fig. 10 Fig. 12

OPERATING THE MOWER
9
+
Height Of Cut
To adjust the height of cut:
Hold the lever and pull sideways to disengage it from the
locking notch, then pull backwards to lower or push forwards
to raise the height of cut. Finally release the lever at the
required position and ensure it locks firmly into one of the
setting notches.
Always select a height of cut to suit operating conditions. Aim
to prevent engine overloading and blockages by avoiding low
cuts in long grass conditions. Be prepared to make two cuts
when the grass is long.
(Refer fig.13)
Grassbag
Raise the rear deflector, lift the grassbag and lower the rear
deflector to rest against the rear of the mower.
To empty the grassbag, pour out the grass clippings and shake
the grassbag vigorously to clean the airways. Good grass
collection depends on good air flow through the grassbag.
When collecting grass clippings it is important that the
grassbag is emptied regularly to prevent blockages and engine
overloading.
(Refer fig.14)
Collection Without Grassbag
Remove the grassbag and operate the mower with the rear
deflector in the closed position.
(Refer fig.15)
Heavy Growth
Areas of heavy growth should be mown without collecting the
clippings. If collection is required, first mow the area without
the grassbag at the maximum height of cut setting.
Allow the grass clippings to dry out and then mow the area
at the maximum height of cut setting with the grassbag fitted.
Reduce the height of cut and mow the area again as necessary
until the required finish is obtained.
To prevent damage to your lawn do not remove more than one
third of grass height in one cut.
(Refer fig.16)
Non Grassed Areas
When moving the mower across non-grassed areas, release
the engine stop lever and ground drive clutch lever to stop the
engine. Set the mower to the maximum height of cut to protect
the cutting mechanism.
(Refer fig.17)
+
Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17

MAINTENANCE SCHEDULE
10
Maintenance Schedule
Follow the hourly or calendar intervals, whichever occurs
first. More frequent service will be required if working for
prolonged periods under dusty, dry conditions, when airborne
debris is present or after extensive operation cutting tall, dry
grass.
First 5 Hours
• After the very first five hours change the engine oil.
• Adjust the autodrive clutch cable, if necessary.
Daily
• Check the oil level.
• Clean grass debris from around the engine, exhaust /
exhaust guard and air ways in the top cowl.
• Clean the underside of the deck housing.
• Check the condition of guards and safety devices.
• Check condition of cutterblade.
• Check condition of grassbag and ensure airways are clear
(replace if damaged).
25 Hours Or Every Season
• Change the engine oil if continuously operating under
heavy load or high ambient temperature.
• Service the air cleaner.
• Lubricate wheels, pivot points and linkages. Grease the
inner control cables at point of entry and exit from their
outer casing.
• Check the clutch cable adjustment.
• Sharpen the cutterblade.
50 Hours Or Every Season
• Change the engine oil.
100 Hours Or Every Season
• Clean the engine cooling system. Clean more often under
dusty conditions, when airborne debris is present or after
prolonged operation whilst cutting tall, dry grass.
• Replace the spark plug.
Engine Detail
(Refer fig.18)
Fig. 18
8
5
76
9
1234
1. Oil Fill/Dipstick 8. Exhaust
2. Start Grip 9. Exhaust Guard
3. Cover
4. Fuel Cap
5. Air Cleaner
6. Carburettor
7. Spark Plug/Lead

MOWER MAINTENANCE
11
Carburettor Adjustments
These adjustments should only be made by an authorised
Briggs & Stratton dealer. Under no circumstances should the
engine be adjusted to run at a speed in excess of that shown on
the Declaration of Incorporation.
Oil Service
Check the oil level daily before starting the engine and ensure
that the correct oil level is maintained. Refer to ‘Assembling
the Mower Before First Use’ for oil checking and filling
instructions.
Change the engine oil after the first 5 hours of operation and
thereafter according to the ‘Maintenance Schedule’.
(Refer fig.19)
1. Drain fuel by running the engine until the fuel tank is
empty.
2. Remove the spark plug lead.
3. Allow the engine to cool.
4. Drain the oil while the engine is warm (not hot).
5. Tip the mower over on to its right hand side thus ensuring
that the air cleaner is kept uppermost to prevent engine
damage.
6. Remove the oil filler dipstick and drain the oil into a
suitable container.
7. Refill with new oil of the recommended SAE viscosity
grade. Refer to ‘Assembling the Mower Before First Use’
Air Cleaner Service
The air cleaner system uses a pleated filter.
Servicing instructions:
1. Open the cover (1).
2. Remove the filter (2).
3. To loosen debris, gently tap the filter on a hard surface.
If the filter is excessively dirty, replace with a new filter.
• Do not oil the cartridge.
• Do not use petroleum solvents.
• Do not use pressurised air.
4. Install the filter (2).
5. Close the cover (1).
(Refer fig.20)
Spark Plug Service
Use only Briggs & Stratton (Part number 19368) spark tester
(1) to check for a spark as shown in the diagram.
(Refer fig.21)
Replace the spark plug every 100 hours or every season,
whichever occurs first. A spark plug wrench is available from
any authorised Briggs & Stratton service dealer.
Check the spark plug gap with a feeler gauge and set at 0.51
mm.
(Refer fig.22)
Keeping Engine Clean
Remove all grass and debris from the engine including the
exhaust/exhaust guard, the air ways in the top cowl and the
surrounding deck areas on a daily basis after use. Never spray
the engine with water during cleaning. Water can contaminate
the fuel. Always clean with a brush or compressed air.
(Refer fig.23)
Grass and debris may clog the engine’s air cooling system
especially after prolonged operation while cutting tall, dry
grass. The internal cooling fins and surfaces may require
cleaning to prevent overheating and engine damage. We
recommended that this service be carried out by an authorised
Hayter Service dealer.
Grassbag
Remove grass debris from the grassbag immediately after use
and check its condition for signs of damage.
To prevent accidents replace a damaged grassbag immediately.
(Refer fig.24)
1
2
1
Fig. 19 Fig. 20 Fig. 21 Fig. 23
Fig. 22 Fig. 24

MOWER MAINTENANCE
12
Deck Housing
Tip the mower onto its right hand side thus ensuring that the air
cleaner is kept uppermost to prevent engine damage. Remove
grass debris from the top and underside of the deck housing
immediately after use.
(Refer fig.25)
Fertilisers and top dressings are particularly corrosive.
Thoroughly clean the mower deck immediately after use on
treated grass and store well away from corrosive materials.
Securing Nuts & Bolts
Regularly check that all securing nuts and bolts are tight.
Replace missing or damaged items immediately.
Clutch Cable Adjustment
Check the clutch cable operation every 25 operating hours and
adjust if necessary. The clutch cable is adjusted correctly when
the belt drive engages with the clutch lever positioned 32 - 38
mm from the handlebar.
(Refer fig.26)
Unscrew the locknuts and screw the adjuster in or out as
necessary. Tighten the locknuts when correctly adjusted.
(Refer fig.27)
Lubrication
Lubricate the wheels, pivot points and linkages with engine oil
every 25 operating hours.
Apply a good quality medium grease to the inner control cables
at the point of entry and exit from their outer casing.
Cutterblade Removal
Drain the fuel by running the engine until the fuel tank is empty
and the engine stops. Remove the spark plug lead and allow the
engine to cool. Turn the mower onto its right hand side and
ensure that the air cleaner side of the engine is uppermost.
(Refer fig.28)
Firmly grip the end of the cutterblade with a gloved hand and
remove the bolt, spring washer and distance piece securing the
cutterblade with a 9/16” A/F spanner.
(Refer fig.29)
To prevent accidents never work on the cutterblade unless
the spark plug lead has been removed. The cutterblade
has sharp edges. ALWAYS wear strong gloves to protect
your hands when working on the cutterblade. DO NOT
rotate tools towards the cutting edges to avoid the risk of
injury should the tool slip. ALWAYS use genuine Hayter
replacement parts.
The condition of the cutterblade and its mounting arrangement
should be checked regularly for signs of wear or damage.
Ensure that the cutterblade is not bent or cracked.
A damaged cutterblade that is out of balance will vibrate
excessively and may break. DO NOT use an unbalanced
cutterblade.
Regularly check that the bolt securing the cutterblade is
tightened to the specified torque of 54 Nm.
Replace the cutterblade every 2 years or sooner if excessively
worn or damaged.
To prevent injury it is wise to seek assistance when turning the
mower onto its side.
Cutterblade Assembly
Assemble the cutterblade with the turned up edges facing
towards the engine. Secure the cutterblade using the bolt (1),
spring washer (2) and distance piece (3).
(Refer fig.29)
Fig. 25
1 2 3
Fig. 28 Fig. 29
32-38mm
Fig. 26 Fig. 27

MOWER MAINTENANCE
13
30-45
Fig. 30
Cutterblade Sharpening
A slightly worn cutterblade may be resharpened. Both blade
edges must be sharpened equally to ensure balance. Sharpen
the cutterblade every 25 mowing hours or more frequently if
conditions require. Remove the cutterblade from the mower
and clean using a brush and water.
Inspect the cutterblade for signs of damage. Sharpen both
cutting edges with a flat file to restore performance.
(Refer fig.30)
Ensure that the cutterblade is balanced. Use a screw driver with
a round shaft to support the cutterblade through its centre hole.
Hold the cutterblade horizontal and then release. A balanced
cutterblade will remain horizontal.
(Refer fig.31)
If the cutterblade is not balanced the heavy end will rotate
downwards. Sharpen the heavy end until the cutterblade is
correctly balanced.
(Refer fig.32)
Storage
Ensure that the cables do not become trapped at the pivot points
when collapsing the mower for storage. To store the handlebar
unscrew the 2 small securing knobs sufficiently to allow it to
be pivoted forwards to rest against the mower. Depress the
engine stop lever to prevent it being damaged through contact
with the engine.
(Refer fig.33)
Engines stored in excess of 30 days need to be protected with
Briggs & Stratton fuel additive or drained of fuel. This prevents
gum from forming in the fuel system or on essential carburettor
parts.
To ensure your mower is maintained in good working order it
is important that the following procedure is adopted. Refer to
the Maintenance section as necessary.
• Drain fuel from the engine by operating the engine until
it stops.
• Disconnect the spark plug lead.
• Change the engine oil.
• Remove the engine spark plug and pour 15ml of engine oil
into the engine cylinder and replace the spark plug.
Do not exceed the stated volume of oil as engine damage
may occur upon restarting. Do not replace the spark plug
lead. Slowly pull the engine start grip once to crank the
engine. This will distribute the oil and help prevent engine
corrosion.
• Clean grass and debris from the engine cylinder, cylinder
head cooling fins, under top cowl, around and behind
exhaust / exhaust guard and ensure that the grassbag is
clean.
• Lubricate the mower and treat metal parts with a water
repellent anti-corrosion product.
• Cover the mower with a protective sheet and store it in a
dry, ventilated area.
Fig. 31 Fig. 32 Fig. 33

LAWN CARE CALENDAR To be used as a guide only
14
January
There is very little work to do this month apart from brushing away leaves. Keep off the grass if
frozen or waterlogged.
February
Rake the grass thoroughly. Spike the lawn to aerate and stimulate soil organisms and root growth
and apply lawn sand if necessary.
March
The yearly lawn work programme really starts this month. As soon as the ground conditions are
suitable, the first cut can be made. The first cut should merely “top” the grass as close cutting
at this stage could result in severe yellowing or browning. Two cuts are generally sufficient this
month.
April
Mow often enough to stop grass growing away. Dig out patches of coarse grass or resistant weed.
Re-seed bare patches.
May
Keep mowing increasing the frequency as required. Treat with selective weed killers or combined
weed/feed preparations if you did not feed the lawn in April.
June
Summer mowing should now be under way. It should be necessary to mow the lawn twice a week.
Raking before mowing is important this month as the combined action keeps runners of clover
under control. Water the grass if necessary, and remember to soak thoroughly.
July
Treat the grass with the second application of fertiliser or weed killer/fertiliser. Water when
necessary and rake occasionally. As a general rule the grass clippings should be removed each
time you mow. If weather conditions are dry and hot and the grass is weed free, leave the clippings
on the lawn to help maintain ground moisture.
August
Keep mowing regularly and watering as necessary. Fill any cracks caused by drought with a
mixture of sharp sand and soil. In dry weather conditions leave the grass longer to help retain
ground moisture.
September
Raise the height of cut to allow the grass to thicken and protect the roots from the winter frost
and snow.
October
Rake out the thatch from the turf and spike the lawn to assist in drainage. Brush in peat and sharp
sand.
November
Use a stiff broom to disperse worm casts before mowing. Keep turf free from leaves.
December
Apart from brushing away leaves, December is a slack end of a busy year. Keep off the lawn if it
is very wet or frozen.
Lawn Stripes
The way to achieve a neat striped effect is for the lawn being cut in parallel stripes, alternate
stripes being mown in opposite directions.Amuch more important routine is to cut at right angles
to the line of the previous mowing. If the work has been carried in a north-south line, then the
next cutting should be in an east-west direction. The cross-cutting keeps down the coarse weed
grasses.
To prevent grass damage do not remove more than one third of the grass height in one cut.

TROUBLE SHOOTING
15
PROBLEM CAUSES CORRECTIVE ACTION
Engine will not turn
over Engine stop lever released Operate engine stop lever
Incorrect oil level Check oil level
Obstruction under deck Remove obstruction
Engine smokes Excess oil Check oil level
Air cleaner cartridge oil soaked or
blocked Service air cleaner
Engine runs then stops Fuel starvation Fill fuel tank
Fuel cap vent blocked Clean fuel cap vent
Engine will not start Engine under load Raise the height of cut
Incorrect / contaminated fuel Drain tank and fill with correct
fuel
Spark plug lead disconnected Connect spark plug lead
Engine brake not released Operate engine brake lever
Faulty spark plug Clean and adjust the gap or
replace
Wiring fault Check wiring
Engine runs rough Spark plug lead becoming
disconnected in use Connect spark plug lead
Faulty spark plug Clean and adjust gap or replace
Air cleaner blocked Service air cleaner
Incorrect / contaminated fuel Drain tank and fill with correct
fuel
Engine vibrates
excessively Mounting bolt loose Tighten bolt
Cutterblade bolt loose Tighten bolt
Cutterblade out of balance Balance cutterblade
Bent crankshaft Consult your dealer
PROBLEM CAUSES CORRECTIVE ACTION
Uneven cut Undulating ground conditions Change direction of travel
Cutterblade worn Sharpen cutterblade
Cutterblade out of balance Balance the cutterblade
Wheels/roller damaged Inspect and replace as necessary
Discharge chute blocks Grass is wet Mow dry grass
Cut height too low Increase cut height
Grassbag full Empty grassbag
No airflow through the grassbag Clean the grassbag
Mower is hard to push Cut height too low Increase cut height
Wheels/roller damaged Inspect and replace as necessary
Mower will not self
propel Drive belt damaged Replace drive belt
Clutch out of adjustment Adjust clutch cable
Poor grass condition No airflow through the grassbag Clean the grassbag
Discharge chute blocked Remove blockage
Wet grass Mow dry grass
Grassbag full Empty grassbag
Cutterblade drive will
not engage / disengage Engine stop lever not fully
forward / released Push fully forward / release to engage / disengage

WARRANTY
16
3 Year Limited Warranty - Home Owner
90 Day Warranty Commercial Use
Hayter Limited warrants to the original user/purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of one year from the date of
purchase. The manufacturers of the engine furnish their own warranty and services are provided through their authorised network (Refer to “EngineWarranty Statement”). To qualify for the full benefit
of the warranty, the Warranty Registration Card must be returned to Hayter Limited within 14 days of purchase. If the selling dealer has not returned the Warranty Registration Card please complete
and return. Subject to the conditions and exclusions noted in this limited warranty, we shall at our option, repair or replace any part covered by the warranty during the applicable period. If you are in
doubt or experience any difficulty, please consult a Hayter Authorised Service Dealer for clarification.
This warranty does not apply to any unit that has been tampered with, altered, misused, abused or used for hire, and will become invalid if non genuine Hayter parts are fitted. This warranty does not
cover for minor mechanical adjustments unless they are due to defective material or workmanship. Consult the Owner’s Handbook or a Hayter Authorised Service Dealer for assistance when making
these adjustments.
Extended 3 Year Warranty
To qualify for the extended warranty period (second and third year) of the three year limited warranty the machine must have an annual service carried out by an Authorised Hayter Service Dealer.
These services should be carried out within 12 and 24 months of the date of purchase. Please note that these services will be charged at a rate agreed between you and theAuthorised Service Dealer.
Excluded from the extended warranty period are those items which are subject to normal wear and tear including but not limited to, tyres, wheels, cutterblades, belts, cables, grassbags, batteries and
other consumable wearing parts.
Commercial Use
Machines used commercially are excluded from the above warranty. Awarranty period of 90 days applies.
Lifetime Warranty Against Crankshaft Bending
All consumer machines which are fitted with a genuine Hayter Friction Disc as original equipment before use, are covered by a Lifetime Warranty against the engine crankshaft bending. Note: friction
washers, Blade Brake Clutch (B.B.C.) units and other such devices are excluded from the Lifetime Warranty coverage. Only machines fitted with a genuine Hayter friction disc, which are used in
accordance with the recommended operating and maintenance procedures, are covered.
Making a Claim
To make a warranty claim, return the unit to a HayterAuthorised Service Dealer along with proof of purchase stating the machine serial number and date of purchase. The service receipt(s) or stamped
service card must be produced as proof of entitlement to the extended warranty period. Subject to the conditions and exclusions in this limited warranty, theAuthorised Service Dealer will, at our option,
repair or replace any warranted part within the duration of the warranty period.
This limited warranty gives you specific legal rights and is in addition to any statutory rights to which you may be entitled and your statutory rights are not affected by this warranty. If you need
additional information concerning this written warranty, or assistance in obtaining services, please write to: HAYTER LIMITED, Service Department, Spellbrook, Bishop’s Stortford, Hertfordshire
CM23 4BU
UK ONLY: Details of your local Hayter Authorised Dealer can be found on the Hayter website www.hayter.co.uk or contact: Freephone 0800 616298.

17
EU PRIVACY STATEMENT NOTES
The Information Hayter Collects
This warranty is jointly administered by Hayter Limited (Hayter) and its affiliate, Toro Warranty
Company (Toro). Hayter and Toro respect your privacy. In order to process your warranty claim
and contact you in the event of a product recall, we ask you to share certain personal information
with us, either directly or through your local Hayter dealer.
Your personal information will be processed by Hayter in the UK. It will also be entered into the
Toro warranty system, which is hosted on servers located within the United States where privacy
law may not provide the same protection as applies in your country.
BY SHARING YOUR PERSONAL INFORMATION WITH US, YOU ARE CONSENTING
TO THE PROCESSING OF YOUR PERSONAL INFORMATION AS DESCRIBED IN THIS
PRIVACY NOTICE.
The Way We Use Information
Hayter and Toro may use your personal information to process warranty claims, to contact you
in the event of a product recall, to gauge customer satisfaction, and for any other purpose which
we tell you about. We may share your information with our parent, The Toro Company, or with
our affiliates, dealers or other business partners in connection with any of these activities. We
will not sell your personal information to any other company. We reserve the right to disclose
personal information in order to comply with applicable laws and with requests by the appropriate
authorities, to operate our systems properly or for our own protection or that of other users.
Retention of your Personal Information
We will keep your personal information as long as we need it for the purposes for which it
was originally collected or for other legitimate purposes (such as regulatory compliance), or as
required by applicable law.
Our Commitment to Security of Your Personal Information
Hayter and Toro take reasonable precautions in order to protect the security of your personal
information. Wealsotakestepstomaintain the accuracyandcurrentstatusof personalinformation.
Access and Correction of your Personal Information
If you would like to review or correct your personal information, please contact us by email at
[email protected].
June 11, 2012

18
NOTES NOTES

19
NOTES NOTES

SERVICE RECORDS & CUSTOMER INFORMATION
20
Hayter Limited
Spellbrook, Bishop’s Stortford,
Hertfordshire CM23 4BU England
Tel: [phone] Fax: [phone]
www.hayter.co.uk
SERIAL NO. LABEL
SERIAL NO. LABEL
Date of Sale:- Engine Type:-
Engine:-
Please ensure that upon completion of each chargeable Service you retain your invoice/receipt.
1st Year (12 Months)
We certify that this service has
been carried out by an
Authorised Hayter Service Dealer
Date:____________________
2nd Year (24 Months)
DEALER DETAILS
DEALER DETAILS
DEALER DETAILS
DEALER DETAILS
We certify that this service has
been carried out by an
Authorised Hayter Service Dealer
Date:____________________
DEALER DETAILS
DEALER DETAILS