HealthyLine PLATINUM Series User manual
NATURAL GEMSTONE
HEAT THERAPY
HEALTHYLINE.COM
HealthLine oers the world’s widest range of aordable, high-quality
far-infrared gemstone heated mats.
PLATINUM
SERIES
ADVANCED
CONTROLLER
INSTRUCTION MANUAL
ADVANCED PEMF
With programmable features:
Waveform (Sine, Square)
Frequency (1 to 25Hz with 7.83 Hz default)
Pulse duration (medium, fast, ultra-fast)
Intensity (10% to 100% of 3000 milligauss)
Time (20 min, 1 hr)
Billions of PEMF combinations!
w
POWER ON
1
3
Connect Controller to the Mat Use Surge Protector Turn Power ON
Information
i
The controller backlight will automatically turn o if
the controller is not touched for more than 2 minutes.
The Controller automatically shuts down if it is not
touched for more than 12 hours.
PRESS
21
HEAT SETTINGS
2
HEAT
MODE
HEAT
ON/OFF
HEAT
MODE
TEMPERATURE
SET and ADJUST
HEAT TIMER
SET and ADJUST
PEMF
FIR
188
188
188
88
1 8:8 8
SETPOINT TEMP
HOURS ON
NI
°F
°C
ACTUAL TEMP
PROGRAM
MIN/HR
Pulse
Sleep
WAVE
TYPE
PROGRAM
ABCD
PROGRAM
ABCD
PROGRAM
ABCD
PROGRAM
ABCD
FREQ
HERTZ
PULSE
DURATION UFM
%
HZ
A
C
BD
PEMF
FIR
188
188
188
88
1 8:8 8
SETPOINT TEMP
HOURS ON
NI
°F
°C
ACTUAL TEMP
PROGRAM
MIN/HR
Pulse
Sleep
WAVE
TYPE
PROGRAM
ABCD
PROGRAM
ABCD
PROGRAM
ABCD
PROGRAM
ABCD
FREQ
HERTZ
PULSE
DURATION UFM
%
HZ
A
C
BD
to Adjust
HH
HH
to Adjust
Actual Temperature is measured at the Core.
Please allow up to 40 minutes for the surface to reach
the maximum temp.
Information
i
HOLD HEAT
MODE
until you hear a BEEP to
switch between °F and °C
Platinum Series
CONTROLLER
This is a complex device, please read thoroughly
i
2INSPIRED BY NATURE, PERFECTED BY SCIENCE.
PEMF
Pulsed Electro-Magnetic Field
CHANGEABLE PEMF MODE
4For terms and definitions see page 4
i
PEMF Time:
20 minutes on - 100 minutes o
Wave Type: Sine
Frequency: 7.83 Hz
Pulse Duration: Medium (M)
Intensity: 50%
DEFAULT SETTING
SET and ADJUST
PEMF
ON/OFF
PEMF TIMER
SET and ADJUST
Set 10, 15 or 20 min of PEMF ON time.
PEMF is set as cycles of
N min ON and 100 min o,
for up to 12 hours with automatic shut-o.
20
MIN
PP
to Adjust
PEMF
MODE
Increase or decrease frequency from 1 to 25 Hz.
1 Hz = 1 PEMF pulses per second. Default PEMF
frequency is set to 7.83 Hz and displayed as 8 Hz.
WAVE FREQUENCY
SET and ADJUST
Hz 88HZ
PEMF
MODE PP
to Adjust
PULSE DURATION
SET and ADJUST
Choose between Ultra-fast (U), Fast (F) and
Medium (M) options that respectively reflect the
Highest, High and Low number of pulses within 1 sec.
UFM
PEMF
MODE PP
to Adjust
Choose between sine and square wave types.
WAVE TYPE
SET and ADJUST
PEMF
MODE
to Adjust
PP
Set the desired intensity as 10%, 25%, 50%, 75%
or 100% of 3000 milligauss.
100%
PEMF
MODE PP
to Adjust
PULSE INTENSITY
SET and ADJUST
w
Preset PEMF Programs
POWER ON/OFF
PHOTON Light ON/OFF
PEMF ON/OFF Decrease PEMF Settings
PEMF Mode change Increase PEMF Settings
HEAT ON/OFF Decrease HEAT Settings
HEAT Mode change Increase HEAT Settings
SLEEP Cycle
Advanced PEMF Programming
PHOTON SETTINGS
3
PEMF
FIR
188
188
188
88
1 8:8 8
SETPOINT TEMP
HOURS ON
NI
°F
°C
ACTUAL TEMP
PROGRAM
MIN/HR
Pulse
Sleep
WAVE
TYPE
PROGRAM
ABCD
PROGRAM
ABCD
PROGRAM
ABCD
PROGRAM
ABCD
FREQ
HERTZ
PULSE
DURATION UFM
%
HZ
A
C
BD
PHOTON PHOTON LIGHT
ON and OFF
Photon lights turn OFF automatically after 1 hour.
Photon lights can be turned ON again at any time.
Lights operate with or without heat.
Intensity of photon light is 2.5 mW/ cm2
Wavelength of photon light is 660 nm
Information
i
Program
Button
Program Type
Default Frequencies,
in ABCD, Hz
F1
Low Frequencies 1, 3, 4, 6
F2
Medium Low Frequencies 7, 8, 10,12
F3
Medium Frequencies 14, 15, 17, 18
F4
High Frequencies 19, 21, 23, 25
F5
Before Sleep 5, 4, 3, 2
F6
Pain Assist 15, 16, 19, 20
F7
Sports Injury & Strain Assist
24, 24, 25, 25
F8
General Regeneration 7.83, 7.83, 10, 10
F9
Earth Frequencies 7.83, 14, 21, 25
F10
Wake Up/Energy 7.83, 10, 11, 12
F11
Energize
Sequence
: F10, F8, F6
F12
Relaxation
Sequence
: F9, F8, F5
Table 1 - Factory preset PEMF functions description
INSPIRED BY NATURE, PERFECTED BY SCIENCE. 3
PEMF
Pulsed Electro-Magnetic Field
Each preprogrammed PEMF function F1-F10 consists
of 4 programs (ABCD). Each ABCD program is 5 min
long and has a unique combination of PEMF Wave
Type, Frequency, Pulse duration, and Intensity.
PEMF function can be changed at any time by pressing
dierent F-button. Active ABCD program will restart
according to the chosen Function.
Functions F1 - F10 can be customized or reset to the
factory settings at any time (see page 4).
Information
i
PREPROGRAMMED PEMF FUNCTIONS
5
Flashing arrow indicates active
programs A, B, C or D.
PROGRAM
A
C
BD
188
88
1 8:8 8
SETPOINT TEMP
HOURS ON
NI
°F
°C
ACTUAL TEMP
PROGRAM
Pulse
Sleep
PROGRAM
ABCD
PROGRAM
ABCD
PROGRAM
ABCD
UFM
HZ
A
C
BD
Negative Ion icon is lit when the heat
is on.
Pulse
Sleep
“Pulse” displayed when PEMF is active.
“Sleep” displayed when PEMF is
non-active during 100 min OFF time.
PEMF
PROGRAM F11
1 HR ENERGIZE
EASY PEMF MODE
Functions will run in sequence: F10 - F8 - F6 (see Table 1).
Controller will shut o after 1 hour. The program is not customizable.
1 HR RELAXATION
EASY PEMF MODE Controller will shut o after 1 hour. The program is not customizable.
Functions will run in sequence, F9 - F8 - F5 (see Table 1).
F12
PEMF
PROGRAM
PEMF
PROGRAM F10
F1 ... PEMF settings of the active program will be displayed on
the screen.
20 MIN PEMF
PICK from TABLE 1
For those who want to use an Advanced PEMF Mode with a Precise Customization.
Do not use PEMF or high heat settings while pregnant.
Do not use PEMF or high heat settings if you have metal implants
or a pacemaker.
Do not use if you have varicose veins.
Do not use with muscle relaxants.
Please consult with your doctor if you have any serious medical condition
before using this or any medical device.
Selected mode will start flashing.
To restore the controller to its factory settings
Factory Reset
i
PRESS AND HOLD SIMULTANEOUSLY
UNTIL YOU HEAR A BEEP
+
+
P
H
PEMF Pulse - A short burst of an electromagnetic wave.
PEMF Wave - Oscillation (disturbance) that travels through space and matter, transporting energy from one place to another.
Wave Type (Sine, Square) - The shape of pulses in an electromagnetic wave. In PEMF this can be Sine, Square or other types, such as sawtooth.
Frequency (Hertz, Hz) - The number of individual PEMF Pulses per second. 1 Hz = 1 PEMF pulses per second.
Pulse Duration - The time from the start of a PEMF pulse, to the end of that PEMF pulse. This is also referred to as “Pulse Width”.
PEMF Intensity (Gauss, G) - The measured level of the PEMF magnetic flux density. The unit of measurement is Gauss. 1 Gauss = 1000 milligauss = 0.0001 Tesla.
PEMF Functions (F1-F12) - Factory preprogrammed PEMF functions. Each of the 12 functions consists of 4 programs (ABCD). Each ABCD program has it’s
own PEMF settings (PEMF Time, Wave Type, Frequency, Pulse duration, and Intensity).
WARNINGS
!
TERMS and DEFINITIONS
Choose a button that will be
re-programmed. Set desired PEMF settings
for Program A (see page 2).
WAVE TYPE
WAVE FREQUENCY
PULS DURATION
PULS
PEMF
MODE
PEMF
MODE
PEMF
MODE
PEMF
MODE
PP
PP
PP
PP
PROGRAM B
WAVE TYPE
WAVE FREQUENCY
PULS DURATION
PULS
PEMF
MODE
PEMF
MODE
PEMF
MODE
PEMF
MODE
PP
PP
PP
PP
PROGRAM C
WAVE TYPE
WAVE FREQUENCY
PULSE DURATION
PULSE INTENSITY
PEMF
MODE
PEMF
MODE
PEMF
MODE
PEMF
MODE
PP
PP
PP
PP
PROGRAM D
WAVE TYPE
PEMF FREQUENCY
PULSE DURATION
PEMF INTENSITY
PEMF
MODE
PEMF
MODE
PEMF
MODE
PEMF
MODE
PP
PP
PP
PP
PROGRAM A
Step 1
Step 2
Step 3
Step 4
Save
settings
PEMF
PROGRAM
Press and Hold
for 5 sec until
you hear a BEEP.
Repeat steps 1 - 4 to set desired
PEMF settings for Programs B, C, and D.
F2
F6
F10
F4
F8
F1
F5
F9
F3
F7
Initiate
Programming
Press and Hold
for 5 sec until
you hear a BEEP.
PEMF
PROGRAM
The controller will automatically
reset and shut down.
PEMF | PROGRAMMING MODE
6
4INSPIRED BY NATURE, PERFECTED BY SCIENCE.
Other manuals for PLATINUM Series
1
Other HealthyLine Controllers manuals
