HearthSong Wonder Wave User manual

1. Arrange the frame pieces in
a circle. Male/female ends
should be placed next to
the piece with the matching
number. The pieces with
hinges attached should be
placed next to one another.
2. Lay out the mat cover,
handles-side up.
3. Locate the two places along
the mat cover’s seam where
two red elastic bands are
next to each other (one pair
each on opposite sides of
the cover). Align the one pair
of red bands with the male/
female ends labeled “1–1”
and the other pair of red
bands with the other male/
female ends labeled “5–5”.
4. Thread the frame pieces
through the fabric loops,
starting at the two red
elastic bands. The frame
ends at both the 1–1 and
5–5 connections should
contain one of two sides of a
hinge and should end up on
opposite sides of the cover at
the two elastic bands.
5. Join the frame pieces to
create two separate halves of
the WonderWave. Make sure
the numbers on the frame
pieces are all face up and
aligned when you join them.
6. I nsert the twelve bolts into
all of the joints (except for
the hinge pieces), turning
slightly, but do not tighten
until assembly is complete.
You may need to twist
the frame pieces slightly
to line up the bolt holes.
Flip the two halves of the
WonderWave over, so that
the handles are facing up.
9. Push down on the sides of
the frame.
10. Add the remaining hinge
bolts into the hinges on both
sides of the frame. There
will be three bolts in each
hinge. Make sure all of the
hinge bolts are screwed in
all of the way and tightened
completely.
11. Tighten all bolts along the
frame.
12. Place two slotted tubular
foam pads on each end of the
WonderWave.
13. Place the polyester foam-pad
covers over the foam pads
and fasten with the attached
Velcro® straps, alternating
them between the mat
cover’s straps.
1-1
7-73-3
8-8
6-6
5-5
4-4
2-2
1-1
7-73-3
8-8
6-6
5-5
4-4
2-2
3
3
44
5 5
6
6
7
7
8
8
11
2
2
What you get:
4 curved frame pieces
4 curved frame pieces with hinges
1 WonderWave fabric mat cover
4 tubular foam pads
2 polyester foam-pad covers
12 bolts with sleeves
6 bolts for hinges (shorter but bigger)
Allen wrenches
#731261
For ages 6 and up.
Takes 3 adults 20 minutes to assemble.
Weight capacity: 500 lbs. with no more than 4 children.
FOR OUTDOOR USE ONLY, ON A SOFT SURFACE
Wonder WaveTM
Assembly Instructions
Join the frame pieces to
create two separate halves of
3
3
4 curved frame pieces with hinges
1 WonderWave fabric mat cover
6 bolts for hinges (shorter but bigger)
FPO, Folded for
storage image
processing
14. To store, remove the
two side bolts from
each hinge and fold the
WonderWave in half. Do
not remove the middle
bolt.
15. To disassemble, remove all
bolts from the hinges and
the frame and remove the
fabric.
SAFETY TIP: Use only on soft
ground, such as grass, and
DO NOT hold on to the metal
edge, as your fi ngers may
get pinched; hold on to the
handles or mat cover only,
as needed. No more than 4
children should be on the
chair at one time. Do not sit
on or straddle the frame when
in use.
It is best to have an equal
balance of weight when more
than one child is on the
WonderWave.
The WonderWave is not
intended for use as a
trampoline. Do not jump on to
or up and down on its surface.
If expecting unusually high,
sustained winds, place the
Wave in a protected area, or
secure with tie downs.
7. Now connect the two halves
of the WonderWave where
they hinge together. Place
one person at each end of
the frame. Push up on both
sides of the frame until the
metal pieces with the hinges
can be aligned.
8. Once they are aligned, insert
one hinge bolt into the center
hole of the hinge on both
sides of the frame.

A fall onto a hard surface can result in serious injury
to the equipment user.
Do not use the equipment until properly assembled.
This rocker is not to be used in any other
manner other than its intended use.
Adult supervision is required.
It is important for adults to instruct children to:
• Dress appropriately while using the rocker
(avoid ponchos, scarves, and other loose-fitting
clothing that is potentially hazardous).
• Wear well-fitting footwear that fully encloses the
foot when using this rocker. Clogs, flip-flops, and
sandals are considered inappropriate footwear.
It is important for adults to instruct children NOT to:
• Walk close to moving rocker.
• Get o of the rocker while it is in motion.
• Climb on the rocker when it is wet.
• Attach additional items to the rocker that might cause
a strangulation hazard.
Maintaining the Rocker
At the beginning of each play season, adults should:
• Tighten all hardware.
• Check all protective coverings on pipes, edges, and
corners. Replace if they are loose, cracked, or missing.
• Check all parts for wear, rust, or other deterioration.
Replace as needed. The hardware used for this
rocker can be found at a local hardware store.
• Check metal parts for rust. If found, sand and
repaint using a non-lead-based paint meeting
the requirements of 16 CFR 1303.
Twice a month during play season, adults should:
• Tighten all hardware.
• Check all protective coverings on pipes, edges, and
corners. Replace if they are loose, cracked, or missing.
Once a month during play season, adults should:
• Check all parts for wear or other
deterioration. Replace as needed.
At the end of each play season or when the
temperature falls below 40°F, adults should:
• Remove the rocker from its outdoor location.
• Store the rocker in a dry environment.
• Spot clean if needed.
Disposing of the Rocker
To dispose of the rocker, first disassemble it. Dispose
of it in such a way that no unreasonable hazards will
exist at the time that the rocker is discarded.
This conforms to ASTM F1148, Consumer Safety Performance
Specification for Home Playground Equipment.
Please retain these instructions for future use.
Made in China. ©HearthSong®2016. Madison, VA 22727 [phone] hearthsong.com
by
Safety Guidelines