HEAT GLO RED40-N-AU User manual

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/13 1
Models:
RED40-N-AU
RED40ST-N-AU
Owner’s Manual
Installation and Operation
DO NOT DISCARD THIS MANUAL
NOTICE
• Leave this manual with
party responsible for use
and operation.
DO NOT
DISCARD
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
Ref No: GMK10107
AS4553:2008
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury, or death.
WARNING
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other ammable
materials.
• DO NOT place articles on or against this appliance.
• Keep clothing, furniture, draperies and other ammable
materials away.
This is a room sealed appliance and no other ventilation is
required than what is provided.
• DO NOT USE OR STORE FLAMMABLE
MATERIALS NEAR THIS APPLIANCE.
• DO NOT SPRAY AEROSOLS IN THE VICIN-
ITY OF THIS APPLIANCE WHILE IT IS IN
OPERATION.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
- If you cannot reach your gas supplier, call
the re department.
• Installation and service must be performed
by a qualied installer, service agency, or the
gas supplier.
WARNING! DO NOT modify this appliance.
All manuals and user guides at all-guides.com
all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/13 77
Figure 16.2 Appliance Dimensions RED40ST-N-AU
Location Inches Millimeters
K 46-3/4 1187
L 7 178
M 50-1/8 1273
N 25-1/16 637
O 17-7/8 455
P 9 227
Q 3-3/4 95
R 1-1/2 38
S 8-1/2 216
T 14-1/2 368
Location Inches Millimeters
A 52 1321
B 13-3/16 335
C 10-3/4 273
D 42-3/4 1086
E 48-1/8 1222
F 21 533
G4 102
H4-3/4 121
I 42-15/16 1090
J17-1/8 435
C
B
A
D
E
F
G
H
I
J
K
L
O
M
N
P
T
Q
R
S
RED40ST-N-AU
All manuals and user guides at all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/1320
Figure 5.5. Clearances to Combustibles-RED40ST
MINIMUM FRAMING DIMENSIONS*
A B C D E F G H I
Rough
Opening
(Vent Pipe)
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width)
Clearance
to Ceiling
Combustible
Floor
Combustible
Flooring
Sides of
Appliance
Front or
Rear of
Appliance
Inches 10 46-3/4 17-1/4 50-1/4 31 0 0 1 36
Millimeters 254 1187 438 1276 787 0 0 25 914
F
I
GH
E
MEASURE FROM TOP OF
FIREPLACE OPENING
C
A
B
D
C
B
D
A
Figure 5.4. Clearances to Combustibles-RED40
MINIMUM FRAMING DIMENSIONS*
A B C D E F G H I J
Rough
Opening
(Vent Pipe)
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width)
Clearance
to Ceiling
Combustible
Floor
Combustible
Flooring
Behind
Appliance
Sides of
Appliance
Front of
Appliance
Inches 10 46-3/4 18-1/4 50-1/4 31 0 0 1 1 36
Millimeters 254 1187 464 1276 787 0 0 25 25 914
F
J
G
I
H
E
MEASURE FROM TOP OF
FIREPLACE OPENING
All manuals and user guides at all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/13 25
Figure 7.4
Top Vent - Horizontal Termination
Venting with 1 elbow
H1V1
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling restops.
• ALWAYS maintain specied clearances around venting and restop systems.
• Install wall shield and ceiling restops as specied.
Failure to keep insulation or other material away from vent pipe may cause re.
WARNING
Note: Use DVP Series
components only.
V1Minimum H1Maximum
1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 6 ft. 1829 mm
3 ft. 914 mm 9 ft. 2743 mm
4 ft. 1219 mm 12 ft. 3658 mm
5 ft. 1524 mm 15 ft. 4572 mm
6 ft. 1829 mm 18 ft. 5486 mm
7 ft. 2134 mm 21 ft. 6401 mm
8 ft. 2438 mm 24 ft. 7315 mm
V1+ H1 = 63 ft. (19.2 m) Maximum
Note: 12 in. (305 mm) minimum verti-
cal is required prior to attaching any
elbow to the appliance.
All manuals and user guides at all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/1326
INSTALLED
HORIZONTALLY
H1
H2
V1
Figure 7.5
1. Top Vent - Horizontal Termination - (continued)
Top Vent - Horizontal Termination
Venting with 2 elbows
Note: Use DVP Series
components only.
V1Minimum H1+ H2Maximum
1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 6 ft. 1829 mm
3 ft. 914 mm 9 ft. 2743 mm
4 ft. 1219 mm 12 ft. 3658 mm
V1+ H1 + H2 = 63 ft. (19.2 m) Maximum
H1 + H2 = 23 ft. (7.1 m) Maximum
Note: 12 in. (305 mm) minimum verti-
cal is required prior to attaching any
elbow to the appliance.
All manuals and user guides at all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/13 27
H2
H1
V2
V1
Top Vent - Horizontal Termination
Venting with 3 elbows
Note: Use DVP Series
components only.
1. Top Vent - Horizontal Termination - (continued)
Figure 7.6
V1+ V2 Minimum HMaximum
1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 6 ft. 1829 mm
3 ft. 914 mm 9 ft. 2743 mm
4 ft. 1219 mm 12 ft. 3658 mm
5 ft. 1524 mm 15 ft. 4572 mm
V1 + V2+ H1+ H2 = 63 ft. (19.2 m) Maximum
H1+ H2 = 23 ft. (7.1 m) Maximum
Note: 12 in. (305 mm) minimum verti-
cal is required prior to attaching any
elbow to the appliance.
All manuals and user guides at all-guides.com
all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/1328
Figure 7.7 Vertical Vent Maximum
Note: If installing a vertical vent/termination off the top of the
appliance, the optional exhaust restrictor may be needed.
V
V = 3 ft Min. (1m), 50 ft. Max. (15.2 m)
Top Vent - Vertical Termination
No Elbows
Note: Use DVP Series
components only.
Exhaust restrictors are recommended for these vertically
terminated products which have excessive draft. Exhaust
restrictors will compensate for high draft, and restore vi-
sual ame height. If the vent conguration has a total
vertical of 20-50 ft (6 m -15.24 m), an exhaust restrictor
may be needed. The exhaust restrictor can be located in
the appliance manual bag.
Figure 7.8 Exhaust Restrictor
NOTICE: Before painting, contact your dealer for
information on the appropriate high temperature paint.
4. In some applications, such as those where the re-
place is elevated off the oor, the vent restrictor may
be painted, but painting is not required.
5. Recommended restrictor usage:
20 to 30 ft. (6 m to 9.1 m) = 4 in. (102 mm) restrictor
30 ft. (9.1 m) and up = 3 in. (76 mm) restrictor
Exhaust restrictor Instructions
1. Locate the two pilot holes in the inside rebox cham-
ber as shown in Figure 7.8.
2. Center the exhaust restrictor such that the thru holes
in the vent restrictor align with the pilot holes in the
inner rebox chamber.
3. Use two 1/2 in. (13 mm) self-piercing screws to se-
cure vent restrictor to rebox heat shield. See Figure
7.8.
EXHAUST RESTRICTOR
All manuals and user guides at all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/13 29
Figure 7.9
H1
V1
V2
Top Vent - Vertical Termination
Venting with 2 elbows
Note: Use DVP Series
components only.
V1+ V2 Minimum HMaximum
1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 4 ft. 1219 mm
3 ft. 914 mm 9 ft. 2743 mm
4 ft. 1219 mm 12 ft. 3658 mm
5 ft. 1524 mm 15 ft. 4572 mm
V1+ H1 + V2 = 63 ft. (19.2 m) Maximum
H1 + H2 = 23 ft. (7.1 m) Maximum
Note: 12 in. (305 mm) minimum verti-
cal is required prior to attaching any
elbow to the appliance.
All manuals and user guides at all-guides.com

Heat & Glo • RED40-N-AU, RED40ST-N-AU • 2294-900 Rev. C • 4/1330
Figure 7.10
INSTALLED
HORIZONTALLY
H1
H2
V1
V2
Top Vent - Vertical Termination
Venting with 3 elbows
Note: Use DVP Series
components only.
V1+ V2 Minimum H1+ H2Maximum
1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 4 ft. 1219 mm
3 ft. 914 mm 9 ft. 2743 mm
4 ft. 1219 mm 12 ft. 3658 mm
5 ft. 1524 mm 15 ft. 4572 mm
V1+ V2 + H1+ H2= 63 ft. (19.2 m) Maximum
H1 + H2 = 23 ft. (7.1 m) Maximum
Note: 12 in. (305 mm) minimum verti-
cal is required prior to attaching any
elbow to the appliance.
All manuals and user guides at all-guides.com