heatco FIREDRUM User manual

FIREDRUM
ASSEMBLY AND USER
INSTRUCTIONS
FIREBASKET
FIREDRUM

WARNING: FOR OUTDOOR USE ONLY
Retain these instrucons for future reference
Before using this repit, make sure you have read, understand and are following all informaon
provided in the following important instrucons. Failure to follow can cause death, serious injury or
property damage. Improper installaon, adjustment, alteraon or maintance can cause injury or
property damage.
IMPORTANT SAFEGUARDS
1. This repit is for outdoor use only and shall not be used in a building, garage or any other enclosed
area. Toxic carbon monoxide fumes can accumulate and cause asphyxiaon.
2. This repit is not for commercial use.
3. This repit should only be used by adults and all children and pets should be kept at a safe distance.
4. Do not use petrol, white spirit, lighter uid, alcohol or other similar chemicals to light a re as a rapid
increase in temperature could damage the repit.This repit is only suitable for use with charcoal, un-
treated wood or dry logs. Do not use coal.
5. Do not use this repit unl it is completely assembled and all parts are securely fastened and ghtened.
6. Do not use the repit on decking or any other ammable surfaces such as dry grass, wood chips, leaves.
7. Always empty this repit aer use. Do not remove ashes or charcoal unl they are completely and fully
exnguished.
8. Do not touch the repit unl it is completely cooled unless you are wearing heat resistant gloves as it is
hot when in use.
9. Do not handle or move the repit when in use as it is hot.
10. Do not aempt to store the repit unl all ashes and charcoals are completely exnguished.
11. Always use a safety tool and heat resistant gloves when adding or moving fuel.
12. Always use a safety tool and heat resistant gloves to move the grill during use because the repit will
become very hot.
13. Do not leave a burning re unaended.
14. Fire hazard-Hot embers may emit while in use.
15. Do not overload the repit with fuel. Do not add addional fuel unl the re burns down. If an poron
of the rebowl is growing red, it is overloaded.
16. Do not burn fuel directly on the rebowl base. Do burn on the log grate
17. Do keep the fuel away from the wall of the repit as the high temperature may damage it.
18. Avoid breathing smoke from the re and avoid geng it into your eyes.
19. Always thoroughly inspect the repit before use.
20. A slight discoloraon of nish may occur aer use.

CARE AND USE
LIGHTING
1. Ensure the repit is posioned on a permanent at, level, heat resistant, non-ammable surface away
from ammable items.
2 Place paper or dry kindling on the log grate in the centre of the rebowl boom.
3. Place fuel on the paper or dry kindling
4. Light the paper or dry kindling to start a re.
TENDING THE FIRE
1. Add fuel to the repit to increase the heat slowly when embers glow. Do not overload with fuel, only
tow or three small logs is sucient.
2. When shiing logs, use a safety tool to allow for addional airow.
EXTINGUISHING
To exnguish the repit, stop adding fuel and allow re to die or douse with sand. Do not use water as this
may damage the repit.
CARE AND INSPECTING
1. This repit should be inspected on a regular base to ensure product safety and longer product life.
2. The repit should be cleaned aer use to ensure longer product life. Do not use oven cleaner or
abrasive cleaner as they will damage this product.
3. When not in use, cover the repit once completely cooled with a cover to help protect it from bad
weather.
4. Store this repit in a dry locaon to maximise product life
5. As the repit is made from steel, the surface will age and develop surface rust as soon as it is placed
outside and afer use. This is to be expected, but it does not aect use and is not a product fault. Please
see below
INSTRUCTIONS ON HOW TO REFRESH THE PAINT FINISH.
Remove loose paint and rust with a wire brush when needed and re-paint using a high temperature paint,
resistant to at least 600°C.
To help reduce surface rust, rub the repit with an oily rag aer each use.
USE AS A BBQ
Before cooking ensure the cooking grill and tools are clean and free of old food residues.
Add about 0.5kg of charcoal on the log grate and light according to the above instrucons
Place the grill onto the top of the rebowl ensuring it is stable.
Do not cook before the fuel has a coang of ash.
Ensure all food is cooked thoroughly before eang.
Aer cooking do not remove the grill unl it has completely cooled.
Aer cooking always clean the grill and the tools.

20, A slight discoloration of finish may occur after use.
Care and use
Lighting
1, Ensure the firepit is positioned on a permanent flat, level, heat resistant, non-flammable surface away from
flammable items.
2, Place paper or dry kindling on the log grate in the centre of the firebowl bottom.
3, Place fuel on the paper or dry kindling
4, Light the paper or dry kindling to start a fire.
Tending the fire
1, Add fuel to the firepit to increase the heat slowly when embers glow. Do not overload with fuel, only tow or
three small logs is sufficient.
2, When shifting logs, use a safety tool to allow for additional airflow.
Extinguishing
To extinguish the firepit, stop adding fuel and allow fire to die or douse with sand. Do not use water as this
may damage the firepit.
Care and inspecting
1, This firepit should be inspected on a regular base to ensure product safety and longer product life.
2, The firepit should be cleaned after use to ensure longer product life. Do not use oven cleaner or abrasive
cleaner as they will damage this product.
3, When not in use, cover the firepit once completely cooled with a cover to help protect it from bad weather.
4, Store this firepit in a dry location to maximise product life
5, As the firepit is made from steel, the surface will age and develop surface rust as soon as it is placed outside
and afer use. This is to be expected, but it does not affect use and is not a product fault. Please see below
instructions on how to refresh the paint finish.
Remove loose paint and rust with a wire brush when needed and re-paint using a high temperature paint,
resistant to at least 600℃.
To help reduce surface rust, rub the firepit with an oily rag after each use.
USE AS A BBQ
Before cooking ensure the cooking grill and tools are clean and free of old food residues.
Add about 0.5kg of charcoal on the log grate and light according to the above instructions
Place the grill onto the top of the firebowl ensuring it is stable.
Do not cook before the fuel has a coating of ash.
Ensure all food is cooked thoroughly before eating.
After cooking do not remove the grill until it has completely cooled.
After cooking always clean the grill and the tools.
PART LIST
1 ( 1x ) 2 ( 1x ) 3 ( 1x ) 4 ( 3x ) 5 ( 3x ) 6 ( 1x )
ASSEMBLY
STEP 1- Loosely connect the firebowl ( 3 ) to the stand ( 5 ) using the bolts ( 4 ).
STEP 2- Tighten all the bolts ( 4 ) to the stand ( 5 ).
STEP 3- Place the stand ( 5 ) on a permanent flat, level, heat resistant, non flammable surface away from
flammable items.
STEP 4- Place the log grate ( 2 ) into the firebowl ( 3 )
STEP 5- Place the grill ( 1 ) on the top of the firebowl ( 3 ).
ASSEMBLY
STEP 1- Loosely connect the rebowl ( 3 ) to the stand ( 5 ) using the bolts ( 4 ).
STEP 2- Tighten all the bolts ( 4 ) to the stand ( 5 ).
STEP 3- Place the stand ( 5 ) on a permanent at, level, heat resistant, non ammable surface away from
ammable items.
STEP 4- Place the log grate ( 2 ) into the rebowl ( 3 )
STEP 5- Place the grill ( 1 ) on the top of the rebowl ( 3 ).