HellArtist 600 scale fuselage 500md User manual

1

2
Thank you for buying HeliArtist Products.600 scale fuselage is designed as an easy way to assembly. Please read this
Instruction manual carefully before assembling the model,and follow all precautions and recommendations in the
manual. ake sure to retain the manual for future reference,routine maintenance,and tuning.The scale fuselage is
designed for T-REX 600E/Nitro Helicopter series.You can easily put it on your T-REX 600E/Nitro for new clothing.
I PORTANT NOTES
R/C helicopters are not toys.R/C helicopter utilize various high-tech products and technologies to provide superior
performance.lmproper use of this product can result in serious injury or even death.Please read this manual carefully
before using and make sure to be conscious of your personal safety and the safety of others and your environment
when operating all HeliArtist products.
anufacturer and seller assume no liability for the operation or the use of this product.lntended usage of this fuselage
is only for adults with experience of flying remote control helicopters at legal flying field.After the sale of this product
we cannot maintain any control over its operation or usage.
After assembling the scale fuselage,the weight will increase and the structure will become more complex,so we do not
recommmend to have any 3D fly as to avoid any accident and damage.
R/C products require a certain degree of skill to operate,and is a consumer item.Any damage or dissatisfaction as a
result of accidents or modifications are not covered by any warrantee and cannot be returned for repair or experience
problems during op eration or maintenance.

3
BEFORE ASSEMBLING
1:Check for all parts in the part list shown at bellow.
2:Some basic tools are needed to help the assembly.
600scale fuselge,suitable for T-REX600 E/Nitro Helicopter series
TOOL
1:Cutter knife. 2:Hexagon screw driver
3:Philli s screw driver. 4:File.
5:Diagonal cutting liers.6:Silicone
7:CA glue. 8:AB glue(e oxy) 9:Fine
sand a er.
10:Scissors.
Fly only in safe areas,away from other people.Do not operate R/C aircraft within the vicinity of homes or crowds of
people.R/C aircraft are prone to accidents,failures,and crashes due to a variety of reasons including lack of
maintenance,pilot error,and radio interference.Pilots are responsible for their actions and damage or injury happened
during the operation or as a result of R/C aircraft models.
1:Plastic Landing Gear x4 8:Sponge collar x1 15:Horizontal stabilizer x1
2:Aluminum Skid x2 9:Hex Cap Screw 3x12mm x2 16:Vertical stabilizer x1
3:Set Screw M3x4 x4 10:Self-Tapping Screw 3x10mm x4 17:Washer ￠3x ￠10x0 8mm x2
4:Self-Tapping Screw T3x10mm x4 11:LED Cover x2 18:Hex Cap Screw 3x35mm x2
5:Wood Piece set 12:Washer ￠3x ￠10x0 8mm x4
6:Washer ￠3x ￠8x0 8mm x4 13:Hex Cap Screw 3x12mmx2
7:Hex Cap Screw 3x14mm x4 14:Hex Cap Screw 3x6mmx8

4
1 2
34
5 6
Use M3x14 screws with M3x8 washers to
assemble the wood blocks onto the heli's
landing gear position
Use epoxy to assemble the wood pieces
according to the above photo (Remarks:
the hight of the wood blocks are depend on
what heli you use )
Use M3x10 Self-Tapping Screws to secure
the Landing Gears to the main wood board
of the fuselage through the hole on the
Landing Gear
Use M3x4 Set Screws to secure the
Aluminum Skids to the Landing Gears
Insert the Plastic Landing Gears into
the landing gear position on the Main
Scale Body
Insert the Aluminum Skids into the
Landing Gears according to the above
photo

5
7 8
910
11 12
Similar as Step 11, use M3x10 Self-Tapping
Screws to secure the front wood block onto
the fuselage bottom plate
Align the wood blocks together with the
heli assembly to the fuselage bottom wood
board Then use M3x12 Self-Tapping Screws
to secure the back wood blocks onto the
fuselage's body
Assemble the tail gear box of the heli
back to the tail boom
Use the sponge collar to hold the
heli's tail boom according to the above
photo
Guide the tail rod of the heli assembly
out of the tail hole on the fuselage
Insert the heli assembly into the
fuselage

6
13 14
15
Assemble the Horizontal and Vertical
stabilizer set to the tail gear box of
the heli by M3x35 Hex Cap Screws with M
3x10 washers
Fit the Vertical stabilizer onto the
trough on the Horizontal stabilizer and
use epoxy to secure them (Remarks: make
sure the Horizontal and Vertical
stabilizers are in perpendicular
condition )
Cut the Side Window covers as to fit the
side window on the fuselage and glue it
onto the side window position (Remarks:
glue all window covers inside the
fuselage's body,same for all positions )
Glue a LED cover on the bottom position
of the front canopy cover according to
the photo shown above
Glue another LED cover on the top of the
fuselage body
Use two M3x12 Hex Cap Screws with M3x10
washers to secure the front canopy of the
fuselage to the Main Scale Body
17 18
16

7
End of Manual