Hello Kitty 68109 User manual

NOTICE
MARQUE: HELLO KITTY
REFERENCE: KARAOKE 68109
CODIC: 4173368

USER'S GUIDE
Karaoke Machine

Warnings and Precautions
CAUTION : TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
WARNING:To
reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
AVERTISSEMENT: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
CAUTION: Use of any controls or adjustments or
performance of procedures other than those herein specifed
may result in hazardous radiation exposure.
WARNING:
Changes or modifcations to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
WARNING:
Do not place the unit on top of any soft,
porous, or sensitive surfaces to avoid damaging the
surface. Use a protective barrier between the unit and
surface to protect the surface.
WARNING:
Use of this unit near fuorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any fuorescent lighting, as it may be the cause.
CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
PRÉCAUTION:
Danger d'explosion si les piles sont
remplacées de faon incorrect. Remplacer les piles
seulement par le méme type de pile ou l'équivalent.
WARNING:
There is a danger of explosion if you
attempt to charge standard Alkaline batteries in the unit.
Only use rechargeable NiMH batteries.
WARNING:
The remote control’s button cell battery
contains mercury. Do not put in the trash, instead recycle
WARNING:Lithium batteries, like all rechargeable
batteries are recyclable and should be recycled or
disposed of in normal household waste. Contact your
local government for disposal or recycling practices in
your area. They should never be incinerated since they
might explode.
WARNING : Shock hazard - Do Not Open.
AVIC:
RISQUE DE CHOC ÉLECTRIQUE - NE PAS
OUVRIR
Mains plug is used as disconnect device and it should
remain readily operable during intended use. In order
to disconnect the apparatus from the mains completely,
the mains plug should be disconnected form the mains
socket outlet completely.
La prise du secteur est utilisé pour déconnecter le
système.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d’entrée, la
prise doit tre débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle bateras viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o
recargables (ni-cad, ni-mh, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE D' LECT
ROCUTION
NE PAS OUVRIR
WARNING : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning fash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
suffcient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
This product utilizes a Class 1 laser to read
Compact Discs. This laser Compact Disc Player is
equipped with safety switches to avoid exposure
when the CD door is open and the safety interlocks
are defeated. Invisible laser radiation is present
when the CD Player’s lid is open and the system’s
interlock has failed or been defeated. It is very
important that you avoid direct exposure to the
laser beam at all times. Please do not attempt to
defeat or bypass the safety switches.

Important Safety Instructions
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not ft into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specifed by the
manufacturer.
12.
Use only with a cart, stand, tripod,
bracket, or table specifed by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
FCC Warnings
NOTE : This equipment has been tested and found to comply
with
the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Additional Warnings
The apparatus shall not be exposed to dripping or splashing and
that no objects flled with liquids, such as vases, shall be placed
on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un
objet.vase, ne doit être placé sur l’
Main plug is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect the
apparatus from the mains completely, the mains plug should be
disconnected form the mains socket outlet completely.
La prise du secteur ne doit pas étre obstruée ou doit étre
facilement accessible pendant son utilisation. Pour étre
complètement déconnecté de l’alimentation d’entrée, la prise doit
être débranchée du secteur.
Battery shall not be exposed to excessive heat such as sunshine,
fire or the like.
Les piles ne doivent pas étre exposes à de forte chaleur, tel qu'à
la lumière du soleil, au feu ou autres choses de semblable.
Caution marking is located at the rear or back of the apparatus.
Attention marquage est situé à l’arrière ou à l’arrière de
l’appareil
The marking information is located at the rear or back of
apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière
de l’appareil.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user
accessible parts.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualifed service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.

Karaoke Machine
Features
CD Player: Support CDG, CD, CD-R/RW
5.5" Black / White Monitor
Mic Volume Controls
Echo Control
AVC Control
Balance Controls
2 Digit red LED display
3.5 mm Phones Jack
2-6.3mm Microphone Jacks
Audio/Video RCA ouput
Audio/Video RCA input
Built-in Loud Speaker
Power: Requires AC power adapter (included) DC 12V 1.5A
Included
Karaoke Machine
Microphone
RCA Audio/Video Cable
AC Power Adapter
AC Adapter

TABLE OF CONTENTS
Warnings and Precautions
Important Safety Instructions
FCC Warnings
Additional Warnings
2
3
Karaoke Machine
Features
Included
4
Introduction
Setup
Power
Play CDG or CDs
Loading a Disc
Playing a Disc
Repeat Function
Programming a Disc
Connecting to a Television / DVD or CD Player
Composite Video Output
Composite Video Input
RCA Aux Input and RCA Audio Output
RCA Audio Output
RCA Aux Input
AVC , ECHO , BALANCE , Phones and Microphones
Automatic Voice Control
ECHO
BALANCE
Connecting Headphones
Connecting a Microphone
6
8
9
10
11
12

Introduction
Front Controls
SOURCE CD DOOR
POWER
PLAY/PAUSE
Press to play or
pause a loaded
disc.
SKIP/SEARCH
Press to skip
between tracks on
a loaded disc.
Press and hold to
fast-forward or
fast-rewind the
current track on
a loaded CD.
This feature does
not work with CDG.
Use to adjust the
source
STOP
Press to stop a
disc during play
REPEAT
Press repeatedly
to set the current
track or entire disc
to repeat
PROGRAM
Press to program a
loader disc to play
tracks in specified
order
MIC HOLDER
MIC VOLUME
Turn to adjust the
volume from the MIC
INPUT.
MASTER VOLUME
Turn to adjust the
volume.
MIC 2 INPUT
STEREO
HEADPHONE JACK
BALANCE
Turn to adjust
the balance.
POWER INDICATOR
MIC 1 INPUT
AVC
Turn to adjust the
automatic voice control
ECHO
Turn to adjust the echo.
LED DISPLAY & INDICATOR
PROGRAM INDICATOR
REPEAT INDICATOR
LED DISPLAY
PLAY/PAUSE INDICATOR

Introduction
Rear Controls
BRIGHT
Turn to adjust the brightness
of the monitor.
CONTRAST
Turn to adjust the contrast
of the monitor.
V
-HOLD
Turn to adjust the vertical
of the monitor.
COMPOSITE VIDEO OUTPUT
RCA AUDIO OUTPUT
DC POWER INPUT(12V 1.5A)
RCA AUX INPUT
COMPOSITE VIDEO INPUT

Setup
Power
Plug the small end of included AC power
adapter to the unit DC JACK and connect
adpater to standard AC power outlet.
Follow the power connect instructions.
Press the POWER button to turn on
your unit that the POWER indicator will
light. Place a disc or connect AUX input
to sounding. Rotate the MASTER VOLUME
to adjust the unit sound level.

Play CDG or CDs
Loading a Disc
1. Push the OPEN / CLOSE area
to open the CD DOOR.
2. Place a CDG or CD into the CD
compartment.
3. Close the CD DOOR.
Playing a Disc
1. Follow the instructions for Loading
a Disc.
2. Adjust the SOURCE switch to
CDG or CD.
3. Press the PLAY/PAUSE button to
begin playing the loaded disc.The
PLAY/PAUSE indicator will light.
4. To temporarily stop playing, press the
PLAY/PAUSE button once (indicator flash).
To resume play ,press the PLAY/PAUSE
button one more.
5. Press SKIP / SEARCH buttons to skip
between next or previous tracks .
6. Hold the SKIP / SEARCH buttons to fast
secarch through the track.
Please note, the fast-forward and
fast-rewind functions will not work
for CDG discs.
7. Press the STOP button to stop playing.
Repeat Function
1. Follow the instructions for Loading
a Disc.
2. Adjust the SOURCE switch to
CDG or CD
3. Press the REPEAT button once and
REPEAT indicator flash. The unit will
play the current track repeatedly.
4. Press the REPEAT button twice and
REPEAT indicaton light. The unit will
play the entire disc repeatedly.
5. To cancel the repeat function: press
the REPEAT button repeatedly to off
the REPEAT indicator or press the
STOP button twice.
Programming a Disc
1. Follow the instructions for Loading
a Disc and Playing a Disc.
2. Press the PROGRAM button and
the program indicator will flash.
3. Press the SKIP / SEARCH buttons
to select the track from the loaded
disc you wish to play first.
4. Press the PROGRAM button confirm.
5. Repeat steps 3 and 4 to program
up to 20 tracks to play in a specified
order.
6. Press the PLAY button to start
the program playing and the
PROGRAM indicator will flash.
7. Press the STOP button twice to cancel
a program.

Connecting to a Television / DVD / Ext. Device
Composite Video output
Requires an RCA video cable
included.
1. Plug the included RCA audio/video
cable into the COMPOSITE VIDEO
OUTPUT and a composite video
input on a television.
2. Adjust the television to the correct
input setting.
3. When playing CDG discs, the
karaoke player will output written
lyrics to the connected television.
Composite Video input
Requires an RCA video cable
included.
1. Connect an RCA video cable to
the COMPOSITE VIDEO INPUT
on the karaoke machine and a
video output on an external video
source.
Adjust the
SOURCE switch to AUX
mode.
Use the native controls on the
external video source to play and
control video.
2.
3.

RCA AUX Input and RCA Audio Output
RCA Audio output
Requires an RCA audio cable
included
1. Plug the included RCA audio/
video cable into the RCA AUDIO
OUTPUT and a RCA audio input on
a television or stereo system.
2. Adjust the television or stereo
system to the correct input setting.
3. When playing disc, the karaoke
player will output audio to the
connected television or stereo
system.
RCA AUX Input
Requires a RCA audio cable
included.
1. Connect an RCA audio/video cable
to RCA AUX INPUT on the karaoke
machine and an audio output on
an external audio source.
2. Adjust the SOURCE switch to AUX
mode.
3. Use the native controls on the
external audio source to play and
control audio.

AVC , ECHO , BALANCE ,Phones and Microphone
Automatic Voice Control
The AVC (Automatic Voice Control)
dial adjusts the volume of the unit
to compensate for varying levels of
volume from the microphone. Turn the
dial to adjust the degree to which the
Automatic Voice Control compensates
for variations in volume.
ECHO
Adjust the
ECHO control to enhance
your voice for a concert hall effect.
BALANCE
Adjust the
BALANCE control to
between the prerecorded singer’s voice
and the muisc when using a
multiplex karaoke disc.
Connecting Headphones
Connect low impedance 3.5mm
(max.32 ohm) stereo headphones
(not included) to this jack. The speaker
is automatically disconnected
when the headphones
plug in.
Connecting a Microphone
Requires a microphone (included)
1. Plug the microphone into the MIC
1 INPUT or MIC 2 INPUT.
2. Adjust the SOURCE switch on the
microphone to the ON position.
3. Use the MICROPHONE VOLUME
dial to adjust the volume of audio
amplifed from the microphone.