Henden H2 User manual

H2 Robotic Pool Cleaner
QUICK START
GUIDE
Register your product online:
www.hendenpools.com.au/productregistration
CAUTIONS AND WARNINGS:
Use the originally supplied power
supply only.
Do not use an extension cable in any
case whatsoever.
Ensure the electrical outlet is protected
by a ground fault interrupter (GFI) or an
earth leakage interrupter.
Keep the power supply out of standing water.
Do not enter the pool while the Robotic Pool Cleaner
is working.
Unplug the power supply before servicing.
Do not pull the Robotic Pool Cleaner from the pool
using the cable.
IMPORTANT
Please read carefully
Thank you for purchasing the Henden H2 Robotic Pool Cleaner.
The Henden H2 uses clever cleaning and navigation technology to keep your pool
sparkling all year long. Designed for easy use and maintenance, the Henden H2 is
a quality piece of pool equipment guaranteed to last.
HELPFUL HINTS
• When working, the power supply should be
placed in the shade.
• Release minimal required floating cable length
to ensure proper pool coverage.
• Leave excess cable rolled outside the pool.
• After each cleaning cycle wash the filter bag or
cartridge. Clogged filter bags reduce scanning
and cleaning efficiency.
• Once a week unplug the cable from the power
supply, unwind the tangled portions of the
cable, straighten it out and leave it in the
sun for several hours.
• When not in use, store the pool cleaner in
a shady place upside down.
SPECIFICATIONS
• Use the Robotic Pool Cleaner in the following
water conditions only: Chlorine Max 4 ppm; pH
7.0-7.8; Temperature 6-34°C (43-93°F); NaCl
Maximum = 5000 ppm.
• Motor protection: IP 68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft

2HENDEN – QUICK START GUIDE
H2 OPERATION
Setup
Before using the Robotic Pool Cleaner for the first time, perform the following steps:
Attach the floating cable to the power supply. Position the power supply at least 3m/10ft away from
the edge of the pool.
Into the Pool
Place the Robotic Pool Cleaner into the pool. Release it
and let it sink to the floor. Make sure that the floating
cable is free of any obstructions.
Out of the Pool
Using the floating cable, bring the Robotic Pool Cleaner
to the pool’s edge. Then grab the handle and remove
from the pool.
Operation
Turn the power supply ON. The Robotic Pool Cleaner
will now operate until it has reached the end of the
cleaning cycle.
ON
1
23m/10ft
1 2
34
5

3HENDEN – QUICK START GUIDE
Installing ultra-fine filters (optional)
The H2 comes with a set of ultra-fine liners to enhance your cleaning experience.
Install these according to the following steps:
H2 OPERATION
Open the filter cover. The basket handle will automatically pop up, making it
easy for you to lift the basket.
Open the latch to release the bottom lid. Rinse well with hose. Once debris is removed close and
place back into your cleaner.
Storage
Coil the cable and store in a cool dry space upside down, or store in a caddy. DO NOT store the robot where it
will be exposed to direct sunlight, excessive heat or to frost.
Cleaning the Filter
It is highly recommended to clean the filter basket after each cleaning cycle.
Note: Don’t let the filter cartridges dry out before cleaning.
Unplug the power supply before servicing.
Position your thumbs on the frame and apply pressure
until they pop out.
H2 Robotic Pool Cleaner
Remove them and place
them aside.
Insert your ultra-fine
liners into the inside of the
basket and click into place.
CLICK
CLICK
1
2
CLICK
6b
7a 7b
7c 7d
8
6a 6c
1
CLICK

MAINTENANCE
Periodic Filter Cleaning
Dismantle the 4 filter panels on the basket, according to these steps:
Cleaning the Impeller
If you notice debris trapped in the impeller:
Unplug the power supply before servicing.
Clean the debris trapped in the impeller opening, according to the following steps:
Position your thumbs on panel and apply pressure until
it pops out. Repeat for all 4 panels.
Clean the filters with a hose.
Reassemble the filter panels. Insert the clean filter basket and close the filter cover.
If the debris is not
reachable follow the
next steps.
Using a short screwdriver open the 2 screws.
Pull the impeller cover
backwards to release. Clean
the debris trapped around
the impeller. Assemble the
impeller cover.
Register your product online:
www.hendenpools.com.au/productregistration
1
CLICK
CLICK
2
3 4
1 2 3