HEPA VacsafeTV4 User manual

1/9
INSTRUCTION MANUAL
MODEL NO: TV4 / TV4X / TV2409
PLEASE READ THE INSTRUCTION MANUAL BEFORE OPERATION

2/9
TV4 PART NAMES
Accessories:
No.
Description
Q'ty
11
Hose set
1
12
Extension pipe
2
13
Crevice tool
1
14
Upholstery nozzle
1
1
Hose clip
2
HEPA filter cartridge
3
Power Switch
4
Filter sealing Plug
5
Motor base
6
Hose Connector
7
Power cord
8
Filter release button
9
Bend connector
10
Air adjuster
11
Hose set

3/9
TV4X PART NAMES
Accessories:
No.
Description
Q'ty
11
Hose set
1
12
Extension pipe
2
13
Crevice tool
1
14
Upholstery nozzle
1
1
Hose clip
2
HEPA filter cartridge
3
Cover
4
Filter sealing Plug
5
Motor base
6
Hose Connector
7
Power cord
8
Filter release button
9
Bend connector
10
Air adjuster
11
Hose set

4/9
TV2409 PART NAMES
Accessories:
No.
Description
Qty
11
Hose set
1
12
Extension pipe
2
13
Crevice tool
1
14
Upholstery nozzle
1
1
Hose clip
2
HEPA filter cartridge
3
Power Switch
4
Filter sealing Plug
5
Motor base
6
Hose Connector
7
Power cord
8
Filter release button
9
Bend connector
10
Air adjuster
11
Hose set

5/9
How to install the HEPA filter cartridge:
Installation of HEPA filter cartridge:
1. Please align the two holes in the HEPA
filter cartridge with the two tabs on the
motor body gently press into place.
2. Allow filter to hinge on these two tabs.
3. Press the filter down & in until the
spring-loaded button clips into place.
(as above 2).
Removal of HEPA filter cartridge:
1. Remove hose & install filter sealing plug.
(Item 4 New one supplied with new filter).
2. Push the filter release button to release the
filter cartridge. (as above 1).
3. Then filter cartridge will spring back from the
motor body (as above 2).
4. Lift filter gently up and off the two top tabs (as
above 3).
5. Install new HEPA filter.

6/9
How to assemble or modify the accessories:
Hose installation and release:
How to change connector of hose:
Release
[Installation]
Remove filter cartridge sealing plug and connect
hose into the suction hole. - * Save the plug
[Release]
Press button down of connector to release
hose.
Disconnection (as A part):
1. Take a small flat screwdriver
and insert it into the round
hole of connecting piece (item
1), then flick out.
2. Remove connector (as 2).
3. Then turn counterclockwise
direction to remove out inner
connector (as 4).
Installation of 90 Deg elbow (as B part):
1. Rotate the inner connector into the
hose until tight (item 1), turning in a
clockwise direction.
2. Align the two holes in the 90 deg
elbow with the two bumps, then press
into the joint (2).
3. Then insert hose connector into 90 deg
elbow (as 3).
4. Insert hose connector into 90 deg
elbow and then slide connecting
pieces on both sides of the hose
connector to complete the hose
assembly job (as C part).
C part :
B part:
A part:

7/9
Air adjuster function:
Purposes of nozzles:
Upholstery nozzle
Crevice tool
Purpose: for a small area, such as a seat,
window, under a desk, etc.
Purpose: for window, narrow groove, corner,
etc.
Specification TV4 / TV4X:
Voltage/Frequency
DC 24~28V
Amperage
Max 24 Amps (soft start)
Power rating (Watts)
650~730 W
Suction power
200W
Power cord length
35 cm
Tank capacity
6.2 L
Weight
6 KGS
Specification TV2409:
Voltage/Frequency
AC 230V
Amperage
Max 3 Amps (soft start)
Power rating (Watts)
700 W
Suction power
200W
Power cord length
5 M
Tank capacity
6.2 L
Weight
5 KGS
If you would like to increase or decrease suction, you
can alter the airflow adjuster by the above operation
showing.
Closing the adjuster off will give you full airflow.
(max capacity).

8/9
Warning:
1. Do not immerse or wash the vacuum in water / to avoid electric shock.
2. DO NOT tilt or drop the cleaner.
3. DO NOT use the Vacuum for hot embers.
4. Do not open Vacuum cleaner electric shock hazard.
(Servicing by qualified technicians only).
5. Do not attempt to clean the filter.
Caution：
1. Please stop operation if the vacuum cleaner stops working and return the unit to an
authorized service center.
2. When vacuum suction capacity slows down or motor shuts down.
1. Check the nozzle, flexible hose, extension pipes if they are blocked or need cleaning.
2. If clear, then replace the filter cartridge.
3. Please note that HEPA filters cannot be cleaned.
To dispose of the old filter, install the sealing plug & dispose of it safely.
⚫If the power cord is damaged, it should be replaced by a qualified electrician.
⚫Do not connect an extension cord that does not match Australian specifications.

9/9
Installation of vacuum cleaner:
295 mm
281 mm