Herman Miller Overlay Installation instructions

Parts Included
Tools Required
HermanMiller
Overlay™Media Mount - Centered
Installation and Disassembly for
Recycling Instructions
How to assemble your Overlay Media
Mount - Centered
Power Driver Phillips Bit M5 Allen Wrench
Stile (2)
Electrical Housing
Media Mount Board
Horizontal Rail (2)
Bezel Trim
Wire Management
Wrap
Snap Duplex Assembly
Side Rail (4)
M8 x 40 Socket
Head Countersink
Machine Screw (4)
M Pan Head Machine
Screw (44) M Pan Head Machine
Screw (4)
Zip Tie
9 
11  12 
10 
Safety Glasses
The centered media mount is used for the following
wall lengths:
A centered media mount is made of two subassemblies:
The centered media mount structure (MN)
The centered media mounting kit (MN)
Mounting Kit
Structure
HermanMiller Assembly Instructions11BN38L rev C

HermanMiller Assembly Instructions21BN38L rev C
Step 3
. Insert hooks on side rails into slots in frame. Push down on assembly to
lock in place.
Note: The top hook engages under the rst large cutout on the inside of the
performance wall frame.
Frame
Rail Assembly
Hooks
. Attach a side rail using () M Pan head machine screws.. Put the stiles into the horizontal rails.
Stile
Stile
Side Rail
Horizontal Rail
Horizontal Rail
Step 1 Step 2
M Pan Head
Machine Screw

HermanMiller Assembly Instructions31BN38L rev C
. Insert hooks on other Side Rail into slots in other side of frame.
. Attach Side Rail to Rail Assembly and Stile with () M Pan Head Screws.
Hooks
Slots
Side Rail
Stile
M Pan Head
Machine Screw
. Attach () remaining Side Rails to assembly with () M Pan Head
Machine Screws per rail.
M Pan Head
Machine Screw
Side Rail
Side Rail
. Attach Media Mount Board to assembly with () Socket Head Countersink
Machine Screws.
. For a standing height monitor attach the boards to the top most position.
For sitting height attach the boards to the bottom most position.
Standing Height Conguration
Sitting Height Conguration
Media Mount
Board
M Socket Head
Countersink
Machine Screw
Step 4

HermanMiller Assembly Instructions41BN38L rev C
Step 6
Step 5
. Attach Electrical Housing to Side Rails with () M Pan Head Machine
Screws.
M Pan Head Machine
Screw
Electrical Housing
. Feed the end of Snap Duplex Assembly through the smaller cutout of the
electrical housing.
. Run the conduit through the bottom horizontal rail.
. Push the duplex into the electrical housing. It will snap into place. . Connect the other end to the base power harness.
Base power harness
All electrical connections must be fully engaged and locked.
Loose connections can cause fire and/or electrical shock.
WARNING
!

HermanMiller Assembly Instructions51BN38L rev C
Step 7 Step 8
. Press Bezel Trim into the opening in the Electrical Housing.
Ring on Electrical
housing
Zip Tie
. Thread the wire management wrap through bottom horizontal rail
and the ring on the back of the electrical housing.
Wire Management Wrap
. Pull the wrap over the top of the ring and secure using the Zip Tie. . Run cabling or telecommunications lines through the wire
management wrap.
Note: If you do not have cabling or telecommunications lines and you
want to cover the cutout at the bottom of the cladding, do so with a
media access cover (MN).

HermanMiller Assembly Instructions61BN38L rev C
Disassembly and Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling
codes. Use these codes to identify material type for recycling. Non marked
components should be treated as mixed plastic. Ferrous metals can be
identied using a small magnet for recycling. Non-ferrous metals should be
separated and recycled separately.
To disassemble product, reverse the above installation steps.
Step 9
. Aer the cladding is attached to the wall, a monitor mounting
bracket is installed on the mounting board.
. Customers will need to provide the monitor mounting bracket that
attaches to the mounting boards.
. A monitor mounting bracket like the Sanus VMPL Dual Purpose
Wall Mount is recommended.
When the Monitor Mount is used on the exterior of the application, such as
a Space Delineation application (shown below), there are specic weight
limitations that the monitor and monitor mount cannot exceed. These are
dependent on the materials used with the Spanner Returns (MN.). See
below:
There are is no minimum weight limit based on materials used in the Spanner
Zone with then Monitor is mounting on the inside of the application when
used with a Return Spanner (MN.R) or a Column Spanner (MN.P). The
Maximum weight the monitors and mounts cannot exceed  lbs. per side.
Media Mounting
Tw o 4’ 0” Returns One 4 ‘ 0” Return & One 6’ 0”
Re t u r n
Tw o 6’ 0” Returns
Weight Limit of 165 lbs .. for any
combination of Spanner Zone
Laminate Cladding, Wood Slats, or
Perforated Metal.
Weight limit of 75 lbs.. w hen both of
the Return Spanners (MN400.R) use
Spanner Zone Tackable Cladding.
Weight Limit of 165 lbs .. for any
combination of Spanner Zone
Cladding, Wood Slats, or Perf orated
Metal.
No Monitor can be mounted on the
outside of the Performance Wall
Cladding if the Return Spanners
(MN400.R) use Spanner Zone
Tackable Cladding.
Weight Limit of 165 lbs .. for any
combination of Spanner Zone
Laminate Cladding, Wood Slats, or
Perforated Metal.