Hessaire HTH01 User manual

HTH01 Instruction 030923 www.hessaire.com
Control Operation
Installation
WARNING: High Voltage can cause serious injury or death.
Control must be installed by a qualified electrician. Turn off
all power before starting installation.
CAUTION: Follow all local building / electrical codes
CAUTION: Do not attempt to repair or service control.
Components are not serviceable.
WARNING: Failure to follow instructions and warnings may
lead to property damage or personal injury.
Troubleshooting
Mounting Control To Wall
Control is designed to mount in an electrical box.(sold separately)
WARNING: Make sure all power is off.
Locate position on wall in area that is convenient to access and
control your evaporative cooler.
Use qualified electrician to install thermostat, run proper sized
wiring and correctly make all connections.
Once all connections are properly made and control is secured
to electrical box, power can be turned back on.
MODEL: HTH01
WiFi Evaporative Cooler Line-Voltage Thermostat
Press and hold MODE button for 2 seconds to select Auto MODE. Use the
temperature arrow setting buttons to set the desired temperature. There will
be a 2 minute “Pre-Wet” cycle which turns only the pump on to wet the media
before the fan turns on. If the room temperature is 4°F higher than the set
temperature, the fan will start on high(Hi) speed. When the room temperature
drops within 2°F of the set temperature, the fan will enter low(Lo) speed until
the set temperature is reached. Both the fan and pump will shut off at this
point. Pressing the fan speed button can also manually set the fan speed in
Auto MODE. The pump cannot be independently turned off in Auto MODE.
Control Functions
Automatic Mode:
Manual Mode:
Press and hold MODE button for 2 seconds to select Manual MODE. In this
mode, the pump can be turned on or off independently. The fan speed can
also be selected independently. The thermostat will not shut off the function
of the cooler in Manual MODE.
Timer:
The timer function is used to turn off the cooler after a set period of time. To
operate the timer function, push the “clock” button to enter the timer setting.
The humidity display box will switch to show the timer display. Use the up
and down arrows to set the desired delay time.
AC115V / 230V 60HZ
Electrical Ratings
INPUT OUTPUT
WHITE/COM
(L2)
RED POWER
(L1)
BLACK:
FAN HIGH
YELLOW:
FAN LOW
BLUE:
PUMP
115Vac: 60Hz, 15.2A 115Vac: 60Hz,
14.0A, 1Hp
115Vac: 60Hz,
9.0A, 1/3Hp
115Vac: 60Hz,
1.2A, 1/40Hp
230Vac: 60Hz, 7.8A 230Vac: 60Hz,
7.0A, 1Hp
230Vac: 60Hz,
4.5A, 1/3Hp
230Vac: 60Hz,
0.8A, 1/40Hp
Issue Possible Cause Action
Cooler won't turn
on / display off
Incorrect wire connections Check connections
Circuit breaker off Reset breaker
Control faulty Replace control
Fan / pump not
turning on
Bad wire connection Check connections
Motor failed Replace motor
Pump failed Replace pump
Control faulty Replace control (WiFi Set Up On Back)
WiFi Control
Auto Set Temperature
Or Override With
Manual Setting
2-Speed Standard
Cooler Motor
Up To 1HP
Pump Controlled
Independently
Automatically
Pre-Wet In
“Auto” Mode
Large, Easy
To Read
Temperature
Dispays
Displays Relative
Humidity In Room
When Timer Is
Not In Use. 12 Hr
Delay Timer Can
Be Set In Hour
Increments
Features
Volts: 115 / 230
Operates all standard evaporative
coolers
Use with standard 2-speed cooler
motors up to 1 HP
Large, easy to read digital displays
Relative Humidity % readout
Delayed off timer up to 12 hours
Fits in single gang wall box
•
•
••
•
•
•

HTH01 Instruction 030923 www.hessaire.com
Setting Up WiFi
EVAPORATIVE COOLER CONTROL WiFi INSTRUCTIONS MODEL: HTH01
Using your mobile device, log in to your WiFi network and turn on Bluetooth. Install the Tuya Smart App by either
scanning the QC code or downloading the app from your play store.
Create your account. You will receive an email code which you will need to enter to verify.
You will receive a terms agreement and be asked to allow Tuya to access your device’s location.
Make your device discoverable by holding the fan button for 5 seconds. The internet symbol will flash on your controller.
Select the “+” to add a device.
Select the Hessaire logo and you will be asked to re-enter your WiFi passcode.
You will receive a message: “Added Successfully”. Select next.
Wait for your app to configure. Select next to finish.
You will now be able to access the controller functions from your mobile device.
Device Controls:
• ON/OFF/MODE
• Fan (High/Low)
• Pump (Cooling)
• Temperature Increase/Decrease
• Timer (Displays RH)
Auto mode will maintain the desired temperature by turning the pump and fan On or Off based on temperature changes.
Manual mode requires you to manually turn the pump and fan on the lower the temperature.
QR Code
Using Your Thermostat Controller With WiFi
Set the desired temperature. The unit will power on in a pre-wet setting for about 2 minutes to allow the media to saturate.
If you are using the manual setting, there is a timer feature to automatically turn off the pump and fan based on the time
you set.
Each time you start up your device, the controller will retain previous settings.
Note: the humidity display is only a readout, it is not an adjustable control function.
WiFi
Symbol
App