Hexagon PEPS 200 User manual

www.myhexagone.com • [e-mail] • Tél. [phone]
®
200
Version UDXYPEPS200N005-EN
Technical manual

SOMMARY
1. Introduction 4
2. Safety rules 5
A. Power Supply Requirements 5
B. Water Requirements 5
C. Rules for safe use 5
3. How to install your PEPS? 9
A. Unpacking 9
B. Electrical connections 9
4. How to use your PEPS? 11
A. Pool entry of the Robot 11
B. Start-up 11
1. Automatic operation 12
2. Manual operation 13
5. Cleaning and maintenance 14
A - Cleaning of filter 14
B - Robot cleaning 15
C - Preventive maintenance 15
D - Change of wear parts 16
6. Usage tips and troubleshooting 17
7. Your warranty 19
A. Conditions 19
B. Warranty period 19
C. Purpose of the guarantee 20
D. Transport damage 20
E. Compliance 20
8. Generic controls 21
Brief instruction for Touch Screen use 22
Spare parts and technical data PEPS 24
General Conditions of Sale Hexagone Manufacture S.A.S. 32
With this product you accept in a tacit and irrevocable manner our general conditions of sale. Photos in this technical manual are not binding.
www.myhexagone.com • [e-mail] • Tél. [phone]
3

1. Introduction
In order to ensure your safety and the validity
of your guarantee, please read carefully and
follow to the letter these instructions.
The bottom pool vacuum cleaner PEPS is the professional robot that must be used only
by the qualified pool technicians.
The bottom pool vacuum cleaner PEPS is desiged for regulair maintenance of your
pool. It does not replace the filtration system and is used only to suck up impurities in
the bottom of the pool.
It should only be used with equipment recommended by the manufacturer. Any other
use is incorrect.
The manufacturer’s instructions for use, maintenance and repairs must be strictly
adhered to.
This technical manual explains how to install, handle and maintain your bottom pool
vacuum cleaner PEPS and how to use its radio control and control box with a touch
screen to control it.
The touch screen dashboard and radio remote control allow you to adjust the speed
and mode of cleaning to your needs, available time, working conditions.
The control box provides a diagnosis of the operation and the various technical
parameters and reports the problems that the robot is facing.
The radio control is designed for manual control and, if necessary, for automatic
program interruption.
We strongly recommend that you:
•read this technical manual carefully by following the installation and
operating instructions very precisely step by step to use your robot PEPS in the
best conditions;
•keep this technical manual for the entire life of the product. It might be useful. If
you have any questions regarding the installation and use of your pool vacuum
cleaner PEPS, please call [phone].
This technical manual is the translation of an original French version.
In the event of any inconsistency between French and translated versions, the French
version takes precedence.
www.myhexagone.com • [e-mail] • Tél. [phone]
4

2. Safety rules
A. Power Supply Requirements
Input: 110 - 240 Volts AC
50-60 Hertz
Output: <15 VDC
IP54
Observe your electrical obligations for the installation of the power supply boxes of
220V / 110V (NFC15-100).
B. Water Requirements
The pool bottom vacuum cleaner PEPS is designed for cleaning the pool bottom under
the following water conditions:
• Temperature: 10o-35o C / 50o - 95o F
• Chlorine: Max 4 ppm
• pH: 7.0 - 7.8
• NaCl: Maximum = 4000 ppm
• No sulfur water
• Never use the robot in water with a salinity ≥ 4mg / l.
C. Rules for safe use
Never use the pool vacuum cleaner PEPS when anybody, especially children or
pets, is in the pool or basin. If people or pets are in the pool or basin, it is possible to
program the swimming pool bottom vacuum cleaner PEPS for use during the hours
when no one is in the pool or basin, for example, at night.
The pool bottom robotic vacuum cleaner PEPS can only be used, maintained and
repaired by persons who are familiar with its special features and the safety instructions.
Please read the user manual carefully and thoroughly familiarize yourself before using
the pool robotic vacuum cleaner PEPS. Do not allow people who are unaware of the
operation of the pool vacuum cleaner PEPS to use or approach it.
Do not place anything, except the radio remote control, on the pool bottom vacuum
cleaner PEPS or its electric box and its control panel.
www.myhexagone.com • [e-mail] • Tél. [phone]
5

2. Safety rules
Do not use the pool bottom vacuum cleaner robot PEPS if you notice a problem on a
part of the robot or see a defective or missing element.
Do not use the pool vacuum cleaner PEPS if the pump or turbine is defective or
damaged. Do not use it if the turbine blades, screws, nuts or cables are defective.
Do not use the pool bottom vacuum cleaner robot PEPS if the main switch does not
operate.
Always switch off the pool bottom vacuum cleaner PEPS using the main power switch
when the robot is not in use. The pool bottom vacuum cleaner robot PEPS can only
be started when the main switch is in position 1 and if the correct PIN code has been
entered.
Hexagone Manufacture SAS does not guarantee the total compatibility between the
pool bottom vacuum cleaner PEPS and other types of wireless device such as remote
controls, radio transmitters, listening loops, roller shutters.
You are not authorized to modify the original design of the pool bottom robotic
vacuum cleaner PEPS. All changes are at your own risk.
The low voltage cable can not be shortened or prolonged. Place the low voltage cable
so that the turbine blades are never in contact with it or that the cable should not be
placed under the pool vacuum cleaner robot PEPS.
Do not drop the self-floating cable plug in water, as it is not waterproof. Furthermore,
do not drop it on the floor, it could damage your tile and even hurt you.
Never attempt to repair a damaged power cable. Contact your dealer for a replacement
by the original cable to avoid any injury.
If by accident the control box falls into the water, it is imperative to disconnect the
electrical socket before to pull it out.
It is forbidden to open the control box as this action can cause an electric shock.
Contact a qualified technician.
www.myhexagone.com • [e-mail] • Tél. [phone]
6

2. Safety rules
The touch screen is fragile. Be careful, especially in cases of shock or elbow blow.
Never allow the robot to operate during storms and always protect the control box
and the touch screen against rain or splash water. Also be sure to protect the control
cabinet and the touch screen from the sun and high heat (maximum 35 degrees), they
must be stored in the shade and in the ventilated space.
Never store the pool bottom vacuum cleaner robot PEPS and its trolley with the control
box and its touch screen in a place where the temperature can fall below 0. Protect it
absolutely from frost.
When the main switch is in position 1 (ON), you must not lift or transport the pool
bottom vacuum cleaner PEPS. It must rest flat on the ground.
When the main switch is in position 1 (ON), you must not lift, transport or return the
pool bottom vacuum cleaner PEPS.
Always switch off the pool bottom vacuum cleaner PEPS using the main power switch
when the robot is not in use. The pool bottom vacuum cleaner robot PEPS can only be
started when the main switch is in position 1.
www.myhexagone.com • [e-mail] • Tél. [phone]
7
IMPORTANT!
Many factors influence the condition of your pool. The pool bottom robotic
cleaner PEPS is a very passive product that does not affect the life of your
pool.
Be aware that over time, the deterioration, color loss, and brittleness of any
pool lining can be caused individually or in combination by the age,
chemical composition or imbalance of the pool water, improper installation,
sunlight, and other factors. All of these factors can contribute to lining
failure. Pool vacuum robots PEPS will not damage the pool lining quality.
Rather, on the contrary, it is more likely that the pool cover will ultimately
lead to wear on the cleaner.
Thus, the presence of such problems in your pool is not related to the use or
operation of a robotic vacuum cleaner PEPS. The manufacturer assumes no
responsibility for the repair or replacement of structures or components of
the customer’s pool. The owner of the pool must assume full responsibility
for the condition and maintenance of the pool lining, water and poolside.

2. Safety rules
WARNING!
When the pool bottom vacuum cleaner PEPS is returned, the
main switch must always be in position 0 and the mains plug
must be disconnected.
You must ABSOLUTELY be sure in this before doing anything!
The main switch must always be in position 0 during all tasks
on the chassis of the pool robotic vacuum cleaner PEPS, such
as cleaning or replacing the turbine.
If you touch the turbine blades in operation, you are at risk of
serious injury. It is strictly forbidden to do!
4
8
100/240V AC
ON
100/240V AC
OFF
www.myhexagone.com • [e-mail] • Tél. [phone]
8

3. How to install your PEPS?
A. Unpacking
Unpack the unit with the necessary precautions. Do not use sharp tools (Cutter, ...).
In the presence of a driver or a technician, check the entire robot - control box, trolley,
chassis, radio control ... . to detect any damage due to transport.
In case of doubt, do not hesitate to make reservations on the transport
voucher by briefly describing the damages sustained. Only the consignee can file a
complaint with the carrier within 48 hours, and by registered letter. In addition, you
must also notify us within 48 hours otherwise we will not be able to do anything.
If your device is not in perfect condition, or if it does not work, notify your dealer
immediately and do not try to turn it on again without the advice of a qualified
technician approved by us.
We recommend that you keep the original packaging and materials for future transport
under perfect conditions.
The packaging must contain the following elements:
• the robot PEPS with its power cable;
• Its trolley;
• the control box and its touch screen;
• the remote control;
• an envelope containing at least the technical manual and the screws for the trolley.
B. Electrical connections
For your safety and the correct operation of your PEPS follow the instructions below:
• Place the control box at a distance of at least 3.5 meters from the edge of the pool,
avoiding direct exposure to the sun or rain. It can be either placed on the ground or
hung on the trolley but in the shade.
• When attaching the control box to the trolley, make sure that the control box is held
securely with the fastening screws supplied with the plate provided and that the trolley
is at least 3.5 meters from the edge of the basin.
• Connect the robot cable to the control box and lock the connector.
• Make sure that the red «I / O» switch on the side is set to «O»
• Only connect the control box to an electrical outlet equipped with a ground terminal
and protected by a residual current protection system of 30 mA maximum (if in doubt,
contact your electrical installer).
• If you use an extension cord to connect your vacuum cleaner to the mains, make sure
that the control box can not be placed within 3.5 m of the pool edge.
www.myhexagone.com • [e-mail] • Tél. [phone]
9

3. How to install your PEPS?
WARNING!
Serious damage can be done to the Robot if it is started when
it is out of the water!
In summary:
Consider the following recommendations for positioning the control box:
• Maintain a minimum distance of 3.5m
between the control box and the edge
of the pool;
• Protect from the rain;
• Protect from direct sunlight.
If the control box is plugged into an
outlet outside, it must be approved for
outdoor use.
It is recommended to use a differential
switch to connect the control box to the
wall socket.
Never install the control box at a height
that is likely to be submerged in water;
place it at least 30 cm from the ground.
It is forbidden to place the control box on the ground. We strongly recommend that
you respect the location of the control box that we made on the trolley.
Make sure that there are no objects such as stones, branches, tools or toys in the
bottom of the pool as it may damage the turbine. Objects presented on the pool
surface may also jam the pool bottom vacuum cleaner robot PEPS (you may need
assistance in removing the object before cleaning can be resumed).
Please remove any objects on the surface (for example, swimming lines) or at the
bottom of the pool (cages, underwater games, etc.) so as not to block the normal
operation of the pool bottom vacuum cleaner PEPS.
Switch the pool bottom vacuum cleaner PEPS on by following the instructions.
When the main switch is in position 1 (ON), be sure to keep hands and feet away from
the rotating turbine. Never place your hands or feet underneath the pool bottom
vacuum cleaner robot PEPS.
3,50 m minimum
Distance trolley / basin
www.myhexagone.com • [e-mail] • Tél. [phone]
10

4. How to use your PEPS?
A - Pool entry of the Robot
• The trolley and the control box of PEPS must be positioned in such a way that the
Robot can reach all the surfaces of the pool while the minimum distance between the
trolley and the edge of the pool is kept at 3.5m.
• Be careful to unroll the entire self-floating cable at the pool edge, avoiding loops,
before putting the unit into the water.
• Place the cable and robot into the water.
• It is essential that the Robot descends by itself and lands flat on the bottom of the
pool.
IMPORTANT INFORMATION!
• Do not operate the robot PEPS out of the water, as this could
damage the pump seals and motors and automatically cancel
the manufacturer’s warranty.
• Do not allow swimming when your PEPS is in the pool.
• When working, the robot should always be flat on the bot-
tom of the pool.
B - Start-up
You can choose whether to operate your PEPS either in automatic mode or in manual
mode.
In automatic mode, the robot will operate for a factory preset time of 10 minutes to
3 hours.
• Plug the electric socket into a ground connection protected by a grounding circuit
breaker.
• Make sure that no one is in the water and that the robot is laid flat on the bottom of
the pool.
• Toggle the red switch «I / 0» which is on the side of the control cabinet to the position
«I». The indicator lights up, which means that your robot is powered on.
• The digital dashboard should light, the Hexagone’s logo should be displayed and the
screen should arrive on its home menu, waiting for your instructions.
www.myhexagone.com • [e-mail] • Tél. [phone]
11

4. How to use your PEPS?
1 - Automatic operation
In this program, named MetroNav, your robot will move according to sequences
predefined in its micro processor, allowing it to detect walls and change direction
according to the dimensions of your pool. The program is made to operate in most
pools by perpendicular cross with a preliminary intellectual clearance.
If this configuration is not suitable for the size or shape of your pool, please contact
your dealer to adapt the robot program to the specific conditions of your basin.
There is a delay button (hourglass) allowing the robot to go 3 hours later; in this case,
please put the black button on the control box in position «I».
• Press the «GO» button to turn on your robot.
• The robot starts in a few seconds. The «AUTOMATIC PROGRESSION» screen of your
dashboard is displayed. This indicates the progress of the pool cleaning and indicates
the remaining time.
• When the program is finished, the robot stops. It is better to bring the robot back with
the radio control close to you rather than pulling on its cable.
• Then toggle the «I / O» switch to the position «O» and disconnect the power cord from
the mains plug.
IMPORTANT!
There are certain pools where the shape, the bottom of the
pool (eg central island, a high level of the bottom mouth ...)
or environmental data such as a temperature (eg water at
10 ° C ...) or the chemical nature of water (eg. very high level
of salinity, a permanent proliferation of algae ...) make it
impossible to use your robot in automatic mode. Please
contact us for more details.
www.myhexagone.com • [e-mail] • Tél. [phone]
12

4. How to use your PEPS?
2 - Manual operation
In this mode, your robot will move in the direction you
will indicate to it using your remote control.
• Toggle the red switch «I / 0» which is on the side of the
control box to the position «I».
• There are different keys on your remote control:
- The «4 direction arrows» correspond to the orientation
of the robot you wish to give it. To move forward, back
or rotate your robot, you must press one of the 4 arrows.
- The «UP» arrow corresponds to the forward movement
of the robot. The rotative brushes of the robot tell you its
forward direction. The back of the robot is where there is
the auto floating cable.
- The «+» button on the remote control corresponds to
the stop of the robot drive motors, but not to the pump.
Thus allows to suck in a very precise place, where a
suction mouth is stopped.
- The «STOP» button is used to completely immobilize
the robot, ready to leave the water or to switch it on
automatic mode.
- The button «1» is used to launch the robot in automatic
mode with immediate start.
- The button «2» is used to launch the robot in automatic
mode with delayed start.
- The «1 and 2» buttons correspond to the automatic
program start. By pressing these buttons, you can not return to the remote control
without pressing first the bouton «STOP».
- After use, set the «I / O» switch to the position «O» and disconnect the power cord
from the mains plug.
IMPORTANT!
A non-activity timer has been set in the radio control mode,
without any command on your part, the robot will turn itself
off after 90 seconds.
www.myhexagone.com
HEXAGONE
MANUFACTURE
HEXAGONE
2
1
AUTO AUTO
STOP
www.myhexagone.com • [e-mail] • Tél. [phone]
13

5. Cleaning and Maintenance
Inspect the pool bottom robotic vacuum cleaner PEPS every week and replace
damaged or worn components.
The following tasks must be performed during weekly inspections:
ATTENTION!
Any manipulation on the robot PEPS necessitates the fact that
the robot is completely disconnected from the power supply.
- Put the main switch in position 0, disconnect the mains plug and put on protective
gloves.
- Clean the filter systematically after each use. In addition, check that the brushes and
belts are not blocked by any chewing gums, bandages, twine, twigs or other objects
that may interfere with the operation of the pool bottom robotic vacuum cleaner PEPS.
- Turn the robot over. Check the following points:
• Clean the body, chassis and filter column. The accumulation of sands, leaves and other
objects in interstices can affect performance.
• Make sure the check valve is not distorted and that it closes well in the down position.
Do not hesitate to replace it if it does not close properly at the water outlet.
• Check that all turbine blades of the robot are intact. Also check that the impeller
blades of the pump move freely.
A - Cleaning of filter
IMPORTANT!
You must clean your filtration in the end of each cycle of your
robot.
Do not exceed the capacity of the filter bag.
The robot should be disconnected from the power supply.
• Turn off the robot and disconnect the control box from the sector.
• Take the robot out of the water and place it on the trolley.
• The impurities have been trapped in the bag, just loosen the drawstring closure at the
bottom of the filter to disconnect it from the robot and access the impurities.
www.myhexagone.com • [e-mail] • Tél. [phone]
14

5. Cleaning and Maintenance
• Empty the bag and clean it with clear water or if necessary with mild soapy water. In
this case, rinse thoroughly, taking care to turn it over.
Do not twist it to wring it, do not put it into the washing machine.
Do not clean with a high-pressure cleaner.
• Also rinse any wastes trapped under the flap and in the turbine.
• Replace the filter bag, making sure that the cord is properly seated on the entire slot
provided in the chassis.
• Retighten the cord closure screw so that the filter can not escape when it is in the
water.
NB1: We advise you to change the filter bag every year for optimal cleaning.
NB2: 3 types of filtration fineness exist, do not hesitate to contact your dealer.
IMPORTANT!
Never operate the robot if the filter is damaged or the fastener
is broken.
B - Robot cleaning
The robot must be cleaned regularly with clean water and you must check and possibly
remove the waste stuck in the drive or in the turbine.
No external mechanical parts require special lubrication or maintenance.
C - Preventive maintenance
To ensure the efficient daily operation of robot PEPS, it is important to check every
week these few points:
• The condition of the belts, their wear rate, tension. Insure if there is no chewing gum
or other stuck in the drive of the pulley or the grooves of the rollers.
• Check the wear of the brushes to avoid damaging the robot and the pool lining
• Unroll the self-floating cable at the edge of the pool to ensure that it can not be twisted
and looped. Ideally, wait about 10 minutes before roll it up.
• Finally, check the general appearance of the robot: screws, the trolley wheels, the
condition of the filter, possible impacts on the body, the battery of the remote control ..
www.myhexagone.com • [e-mail] • Tél. [phone]
15

5. Cleaning and Maintenance
D - Change of wear parts
The wheels are one of the major elements of the correct operation of the drive.
Depending on the time and frequency of cleaning, the wear time is different from one
robot to another, but with our experience, we can adviser to change the wheels every
18 months or 1 time per 2 seasons.
We also advise you to change the rotating brush belts after a season of use.
The brushes must be changed if their surface becomes almost smooth or worn.
WARNING!
Always use an original stainless steel turbine, belts and
screws for replacement.
When replacing the turbine, make sure that the robot is not
connected to the power supply.
Under no circumstances should you handle the robot chassis
when the robot is connected to its control box. In addition, we
advocate to make sure that the robot, in except of operation
on the pool bottom in automatic or manual mode by using the
radio remote control, must be turned off and disconnected
from the power supply.
If you touch the turbine blades in operation, you are at risk of
serious injury. It is strictly forbidden to do!
www.myhexagone.com • [e-mail] • Tél. [phone]
16

6. Usage Tips and Troubleshooting
Your safety:
Your robot PEPS has been manufactured according to the most rigorous standards.
To ensure a safe operation, follow the instructions and the security rules indicated in
this technical manual (pages 5-8).
• Only connect the Control Box to a power outlet with an earth connection and
protected by a residual current circuit-breaker of 30mA maximum.
• To avoid electric shocks never open the Control Box. Call to a qualified service
technician.
• Never attempt to repair a damaged power cable. Contact the After-Sales Service in
order to replace it by the original cable to avoid any injury.
Usage tips :
Use your vacuum cleaner as often as possible: you will enjoy a always clean pool and
the filter bag will clog up slower.
• It may happen that a part of the swimming pool is not perfectly cleaned after the
automatic program of your robot. In this case, you can use the manual mode to perfect
the cleaning in a very short time.
• Never put the Robot in the pool if you cannot see the bottom of the pool or in the
presence of too much algae.
• Store the Robot in a ventilated, frost-free room, not containing chemicals and acids.
www.myhexagone.com • [e-mail] • Tél. [phone]
17

6. Usage Tips and Troubleshooting
In case of problem :
A - The robot slides and doesn’t make good trajectories
There may be 3 reasons:
• The filter bag is full or dirty: just clean it.
• Although the water appears clear, there are microscopic algae in your basin that are
not visible to the naked eye, which make the bottom slippery and prevent the robot to
roll properly. So make a chlorine shock and slightly lower the pH (between 7 and 7.3).
Do not leave the robot in the water during shock treatment.
• The robot has a problem with its drive, wheel or motor, and does not have enough
power to drive.
NB : The robot PEPS has never been
designed to go up the walls or sloping
sidewalls of over 20 ° inclination
B - The robot does not move
Check that the socket on which the control box is connected is well supplied.
• Check that you have :
- Correctly connected the self-floating cable to the control box,
- Correctly set the red switch located on the side of the Control Box in the «ON» position
and that the indicator light is lit,
-The delayed start is not switched «ON» thanks to the black button positioned on «I» .
If the problem persists, contact your dealer.
C - The efficiency of the cleaning seems to be decreasing
• Check that the filter is not dirty or clogged.
• Make sure that the suction pump is working and that the turbine is not blocked by an
object
• Check the condition of your brushes and your wheels
• Check that the cable is not too twisted and does not make too many loops during
operation.
20°
maxi
www.myhexagone.com • [e-mail] • Tél. [phone]
18

7. Your Warranty
The present conditions correspond to the French laws in force at the date of their
printing.
A - Conditions
We guarantee that all materials are technically sound and free of defects of materials
and manufacture and that they are consistent with the state of the art and techniques
at the time of entry to the market. Subsequent technological modifications applied to
our products due to technological progress cannot give rise to any intervention on our
part.
The warranty is limited to the repair or replacement of the equipment if a compliance
defect is recognised.
The choice of the solution is at our discretion given that any application of the warranty
could not exceed the resulting direct losses suffered and cannot lead to unreasonable
costs to the dealer or the manufacturer.
The warranty is cancelled as of right if the equipment has been worked upon by a
third party who does not belong to our workshop or by a repairer not certified by us
or if modifications have been applied without our written consent. The warranty is also
cancelled as of right if the operation and maintenance does not comply with the
operation manual supplied with the equipment at purchase time.
All legal warranties as described in section 1641 of the Civil Code are applicable. Any
text that could become Law after the printing of the present guarantee and whose
terms would be in the order of public interest would automatically apply even if they
are different from the present conditions.
The following are excluded from the warranty:
• Replacement of wear parts such as tracks, brushes, belts, filter bags.
• Electrical damage caused by lightning or poor electrical connection.
• Breakage due to shocks.
• Any breakdown related or non-related to replacement with non-original parts.
• Problems arising as a result of non-compliance to the instructions of the operation
manual.
Under no circumstances may the repair or replacement under the warranty extend or
renew the warranty period of the device.
B - Warranty period
The warranty period is 2 years from the date of invoice to the first user.
www.myhexagone.com • [e-mail] • Tél. [phone]
19

7. Your Warranty
C - Purpose of the guarantee
During the warranty period defined above, any component recognized as defective will
be repaired or exchanged by the manufacturer by a new part or another one that is in
good operating condition.
Subject to any French legal provisions of public order that may be put into effect after
the issue of this warranty, transport and labor costs will be borne by the user.
In case of return to the workshop, the two-way transport costs will be borne by the user,
the labor costs remain the responsibility of the manufacturer.
The immobilization and deprivation of enjoyment of the equipment due to its repairs
cannot give rise to any compensation. In any case, the legal warranty of the seller
continues to apply under section 4 of Decree n° 78-464 of the 24th of March 1978.
D - Transport Damage
The equipement is always transported at the recipient’s own risk. The last is responsible
to verify that the equipment is in perfect condition before accepting delivery. We can
not be held responsible in this matter.
E - Compliance
This equipment has been designed and manufactured according to the following
standards:
• NF C15-100
Extra-low voltage supply for security
•NF EN 61000-6-3 March 2007
Electromagnetic compatibility (EMC) - Part 6-3 : generic standards - Emission standard
for residential, commercial and light-industrial environments
Additional information relative to CE certification
The swimming pool bottom vacuum cleaning robot PEPS is certified CE according to
the following instructions:
• Machine directive 2006/42/CE
•C.E.M. 89/336/CEE and 92/31/CEE
• Low voltage 2014/35/UE with which the equipment is compliant.
The product has been tested under normal conditions of use.
www.myhexagone.com • [e-mail] • Tél. [phone]
20

7 – Generic controls
Applied to the device No. series
PEPS200- ____
The verification of controls was carried out by
Signature:
Date:
Step
Controls
Initials of Operator
A
Robot Tests
Ok
B
Trolley Tests
Ok
C
Control Box Tests
Ok
D
Packaging control
Ok
8. Generic controls
www.myhexagone.com • [e-mail] • Tél. [phone]
21