HFCL io HSP-IO-24GE4XS-C2A User manual

Quick Start
Guide
24 Port L2
Managed Switch
Applicable on:
HSP-IO-24GE4XS-C2A
IO 24-Port Non-PoE,L2 Managed Switch with
4x1/10G SFP+ Uplinks and Single AC Power Supply
HSP-IO-24GE4XS-C2AH
IO 24-Port Non-PoE, L2 Managed Switch with
4x1/10G SFP+ Uplinks and Dual AC Power Supplies
HSP-IO-24GE4XS-C2PAH
IO 24-Port PoE+,L2 Managed Switch with
4x1/10G SFP+ Uplinks and Dual AC Power Supplies

02
Indigenously developed
Secured Network OS
High Speed Fiber
& Copper based backhaul
Zero Touch Provisioning
& Automation Capabilities

Thank you for choosing the 24-port L2 commercial Switch from HFCL
Switching Platform (HSP). PoE Variants Suitable in an
enterprise/telco/campus environment to connect PoE clients like Wi-Fi
AP, CCTV, P2P, P2MP, IoT etc. Non-PoE Variants Suitable to connect
Small Cells / BTS, P2P/P2MP etc. in a telco environment and
Desktops/Servers, IP-Phone etc. in an Enterprise/Campus environment.
03
Introduction
24x10/100/1000
RJ 45 Ports 4x1/10G
SFP+ Uplink Ports
1x USB
Port
1x Mgmt Port
1x Console Port
Ground
AC power input

04
Packaging Content:
24 Port Switch Qty: 1 number
1.
Mounting clamps with screws
2.
Standard power supply cord (1.5m)
3.

05
Bracket Assembly
Step 1. Secure the brackets to the device using the supplied
screws from the Mounting Accessory.
Step 2. Install the device in the rack using four rack-mounting
screws. Ensure that you secure the lower rack-mounting
screws first to prevent the brackets from bending due to the
Switch's weight.
Step 3. If installing multiple Switches, mount them in the rack,
one below the other, in any order.
Step 4. Turn on the power supply in the Switch securely.
Assembly of brackets for Rack mounting described in below diagram
for 24 Port L2 commercial Switch model.
24-Port L2 Switch Model

The console access to the Switch can be obtained via the console
port using RJ45 to DB9 serial port adapter. An administrator can
access the device using command line interface (CLI) with the
following console port setting as part of factory default configuration.
06
Speed:115200 bps | Data bits: 8
Stop bit: 1 | Parity: none
Flow control: hardware
Login access

Product specification
Capacity Switching: 128 Gbps,
Forwarding: 95.232 mpps
Port Configuration 24x10/100/1000 Base-T Gigabit Access Ports
(PoE+ variants and Non-PoE variants)
Uplink Ports 4x1/10G SFP+ Uplink Ports
PoE Feature Smart PoE, PoE variants suitable as access or
aggregation Switch and deployment of Wi-Fi
AP/CCTV/IP Phone
L2 features Support 4094 VLAN IDs, 16K MAC Table
Security L2, L3, L4 ACLs, 802.1X Authentication
(RADIUS, TACACAS+)
Storm Control Broadcast, Multicast and Unknown Unicast
Management CLI, Telnet, SSHv2, SNMP v1/v2/v3 and ZTP
Temperature Operating: 0 to 55 degree C
Power Input 100V to 240V for AC
24 Port L2 Managed Switch Specifications
07

ACT Green/Yellow
Yellow blinking
Green blinking PoE on with activity
Solid Green PoE on with no activity
OFF Non PoE with no activity
Non PoE with activity
LINK Green/Yellow
Solid Green
Solid Yellow Link Up at 100Mbps speed
OFF No Link
Link Up at 1000Mbps speed
LED Label LED Colour Indication Status
SM Blue
OFF
Blinking Power up sequence
in process
Solid ON System is booted
and operational
System is powered OFF
ALM Red
OFF
Blinking Alarm reported
Solid ON Critical alarm reported
No alarms reported
LED Label LED Colour Indication Status
Port LED status
System LED status
08

Observe the following safety
precautions to avoid damage
to the Switch:
Do not power the device during installation.
Keep away from high voltage cables.
Do not power off the unit in the middle of an upgrade process.
Do not open the enclosure.
Safety Precautions
09

HFCL Limited All Rights Reserved. HFCL and io by HFCL are trademarks or registered
trademarks of HFCL Ltd. Specifications are subject to change without notice.
8, Commercial Complex,
Masjid Moth, Greater Kailash-II,
New Delhi- 110048
[email protected]
hfcl.com | io.hfcl.com
Contact Us:
by HFCL
Revision: A
Part Number: QSG-04-0004