HFCL io HSP-IO-8GE2S-C2PA User manual

Quick Start
Guide
8 Port L2
Managed Switch
Applicable on:
HSP-IO-8GE2S-C2PA
IO 8-Port PoE+ L2 Managed Switch with 2x1G SFP
and 2x1G RJ45 Uplink ports and Single AC Power Supply
HSP-IO-8GE2S-C2PD
IO, 8-Port, PoE+, L2 Managed Switch,
2x1G SFP + 2x1G RJ45 Uplinks, Single DC Power Supply
HSP-IO-8GE2S-C2D
IO, 8-Port, Non-PoE, L2 Managed Switch,
2x1G SFP + 2x1G RJ45 Uplinks, Single DC Power Supply
HSP-IO-8GE2S-C2A
IO, 8-Port, Non-PoE, L2 Managed Switch,
2x1G SFP + 2x1G RJ45 Uplinks, Single AC Power Supply

Indigenously developed Secured Network OS
High Speed Fiber & Copper based backhaul
Zero Touch Provisioning & Automation Capabilities
02

Thank you for choosing the 8-port L2 commercial Switch from
HFCL Switching Platform (HSP). PoE Variants Suitable in an
enterprise/telco/campus environment to connect end PoE
clients like Wi-Fi AP, CCTV, P2P, P2MP, IoT etc. Non-PoE
Variants Suitable to connect Small Cells / BTS, P2P/P2MP etc.
in a telco environment and Desktops/Servers, IP-Phone etc. in
an Enterprise/ Campus environment.
03
Packaging Content
Introduction
8 Port Switch Qty: 1 number
1.
Mounting clamps with screws
2.
AC Power Cord 1.5m (with AC variants)
3.
DC Connector (with DC variants)
4.

04
8 Port L2 Switch Model
Bracket Assembly
Bracket Assembly
Step 1. Secure the brackets to the device using the supplied
screws from the Mounting Accessory.
Step 2. Install the device in the rack using four rack-mounting
screws. Ensure that the lower rack-mounting screws are
secured first to prevent the brackets from bending due
to the switch's weight.
Step 3. If installing multiple switches, mount them in the rack,
one below the other, in any order, maintaining required
space for cabling.
Step 4. Securely connect to power source and turn on to
configure and operate.
Assembly of brackets for Rack mounting described in below diagram
for 4 Port L2 commercial switch Model

05
Capacity Switching: 24 Gbps,
Forwarding: 17.86 mpps
Port Configuration 8x10/100/1000 Base-T Gigabit Access Ports
with PoE+ and Non- PoE support
Uplink Ports 2x10/100/1000 Base-T
2x1G SFP Gigabit Uplink Ports
PoE Feature 240W (PoE Budget), Smart PoE
L2 features Support 4094 VLAN IDs, 16K MAC Table
Security L2, L3, L4 ACLs, 802.1X Authentication
(RADIUS, TACACAS+)
Storm Control Broadcast, Multicast and Unknown Unicast
Management CLI, Telnet, SSHv2, SNMP v1/v2/v3 and ZTP
Temperature Operating: 0 to 55 degree C
Power Input 100V to 240V for AC and -44V to 57V for DC
8 Port L2 Managed Switch Specifications
Product specification

The console access to the Switch can be obtained via the console
port using RJ45 to DB9 serial port adapter. An administrator can
access the device using command line interface (CLI) with the
following console port setting as part of factory default configuration.
07
Speed: 115200 bps | Data bits: 8
Stop bit: 1 | Parity: none
Flow control: hardware
Login access

ACT Green/Yellow
Yellow blinking
Green blinking POE ON with Activity
Solid Green POE ON with no activity
OFF Non PoE with no activity
Non PoE with activity
LINK Green/Yellow
Solid Green
Solid Yellow Link Up at 100Mbps speed
OFF No Link
Link Up at 1000Mbps speed
LED Label LED Colour Indication Status
SM Blue
OFF
Blinking POE ON with Activity
Solid ON POE ON with no activity
Non PoE with activity
ALM Red
OFF
Blinking Alarm reported
Solid ON Critical alarm reported
No alarms reported
LED Label LED Colour Indication Status
Port LED status
System LED status

Observe the following safety
precautions to avoid damage
to the Switch:
Do not power the device during installation.
Keep away from high voltage cables.
Do not power off the unit in the middle of an upgrade process.
Do not open the enclosure.
Safety Precautions

HFCL Limited All Rights Reserved. HFCL and io by HFCL are trademarks or registered
trademarks of HFCL Ltd. Specifications are subject to change without notice.
8, Commercial Complex,
Masjid Moth, Greater Kailash-II,
New Delhi- 110048
[email protected]
hfcl.com | io.hfcl.com
Contact Us:
by HFCL
Revision: A
Part Number: QSG-04-0002