HFCL io HSP-IO-8GE2S-I2PDH User manual

Quick
Start
Guide
8 Ports Industrial PoE Managed Switch
MODEL: HSP-IO-8GE2S-I2PDH

Indigenously developed Secured Network OS
High Speed Fiber & Copper based backhaul
Zero Touch Provisioning & Automation Capabilities
02

Thank you for choosing 8-port PoE+ Industrial Switch from HFCL
Switching Platform (HSP). The Switch has all Gigabit ports with
access ports PoE+ enabled. This is L2 Managed Industrial
Switch with 2x1G SFP and 2x1G RJ-45 uplink ports enabling
termination of both copper and optical cables simultaneously.
Packaging Content
8 Port Switch Qty: 1 number
This Switch can be mounted in a rack
using din rail mounting.
03
Introduction

04
Capacity Switching: 24 Gbps,
Forwarding: 17.86 mpps
Port Configuration 8x10/100/1000 Base-T Gigabit
Access Ports with PoE+ support.
Uplink Ports 2x10/100/1000 Base-T
2x1G SFP Gigabit Uplink Ports
PoE Feature 240W (PoE Budget), Smart PoE
L3 Features Static Route and Inter-VLAN Routing,
Dual Stack and IPv6
Security L2, L3, L4 ACLs, 802.1X Authentication
(RADIUS, TACACAS+)
Storm Control Broadcast, Multicast and Unknown Unicast
Management CLI, Telnet, SSHv2, SNMP v1/v2/v3
Temperature Operating: -40 to 75 degree C.
Dimensions 193 mm (Width) x 51 mm (height) x 138 mm
(depth).
Weight 1.25 Kg
Power Input 44V to 57V DC
HSP-IO-8GE2S-I2PDH Specifications

05
1x Console Port
Heat Sink Cover
8x10/100/1000
PoE+ Ports
2x1G RJ45 +
2x1G SFP Uplink Ports
System
LEDs
Ground
2xDC
Power Input
DIN Rail
Mounting
Product Overview

06
To install the switch on a DIN rail, perform the following procedure:
DIN Rail Clamp
DIN Rail Spring
DIN Rail
Move the slot at the top of the DIN rail bracket onto the upper
edge of the DIN rail.
Apply downward pressure on the spring within the bracket
located at the top rear edge of the switch until the bottom edge
of the front faceplate of the switch can be pushed backward and
positioned under the lower edge of the DIN rail.
Release the pressure on the top of the switch to allow the DIN
rail bracket spring to securely fasten the bracket to both the top
and bottom of the DIN rail.
Perform a visual inspection of the bracket to ensure that the DIN
rail is now inserted into both the upper and lower ports of the
DIN rail bracket.
1.
2.
3.
4.

The console access to the Switch can be obtained via the console port
using RJ45 to DB9 serial port adapter. An administrator can access the
device using command line interface (CLI) with the following console
port setting as part of factory default configuration.
Check the LED status
P1
ON, Green
OFF
Power line has power
Power line is disconnected
or does not have power
P2
ON, Green
OFF
Power line has power
Power line is disconnected
or does not have power
Alarm ON, Red
OFF
When failure occurs
No failure
SYS
Speed
LEDs for
RJ-45 ports
Speed
LEDs for
SFP ports
ON, Orange
Blinking,
Orange
ON, Green
ON, Amber
OFF
1000-Mbps connection is detected
10/100 Mbps connection is detected
No link is detected
Switch is working properly
System is booting UP
ON, Green
OFF
1000-Mbps connection is detected
No link is detected
07
Speed:115200 bps | Data bits: 8
Stop bit: 1 | Parity: none
Flow control: hardware
Login access

08
Observe the following safety
precautions to avoid damage
to the Switch:
Do not power the device during installation.
Keep away from high voltage cables.
Do not power off the unit in the middle of an upgrade process.
Do not open the enclosure.
Safety Precautions

HFCL Limited All Rights Reserved. HFCL and io by HFCL are trademarks or registered
trademarks of HFCL Ltd. Specifications are subject to change without notice.
8, Commercial Complex,
Masjid Moth, Greater Kailash-II,
New Delhi- 110048
[email protected]
hfcl.com | io.hfcl.com
Contact Us:
by HFCL
Revision: A
Part Number: QSG-04-0001