HI MART NHC-609 User manual

NHC-609
4 Bars & 2 Shelves 1 Pants (32mm)
www.himart.co.nz
3C/89 Ellice Rd. Glenfield, North Shore
Shop 2, 2 Bishop Dunn Pl. Flat Bush
Ph) 4449114, 9486440
Since 1999
Making the Pillar Stand Pillar and Component Seing
Product Size : 217cm (width), 170~253cm (height), 32cm (depth)
Spring operation
makes it go up
about 2~3cm higher.
Set up the pillar after
inserting lower pillar
in the below fixation
board.
Fasten the safety
bolt( ) with hands.
Set up the pillar lean-
ing upper pillars to-
ward the wall a little.
Move pillars to the setting place. Hold lower pillar and
upper pillar, one pillar with one hand, pull the pillar toward
the ceiling and fix it on the ceiling and bottom accurately.
The pillar is fixed strong due to the spring operation of the
upper fixation board (attach it on the ceiling by pulling
about 2~3cm with possible power)
After setup the pillar, fasten the safety bolt with hands at
one touch fixation device for use safety.
Explanation on pictures
Notice If you do not tight upper pillar, it may fall.
Please strengthen the power given to the top of pillar.
upper pillar
lower pillar
Basket shelves
Hanger
horizontal bar
Open circle
holder
approx 75cm approx 75cm approx 75cm
Pillar 1 Pillar 3 Pillar 4
►Arrange pillars at the same space in making pillars stand.
►After leveling respective holders, set up parts as shown in
picture.
►After regulation open holder to the wanted height with
rubber ring, fasten safety bolt at the back.
►Please push down
the Pants hanger
bar into the Pants
hanger bar holder.
Products have different colours but setting method is same.
Open circle
holder
Safey bolt
Hanger
horizontal bar
Basket shelves
holder
Pants hanger
Pants
hanger bar
Basket shelves
Basket shelves
holder
Pillar 2
one touch
fixation device
Pants hanger
bar holder
Pants hanger bar holder
Pants hanger bar

5
1
2
3
4
7
6
5
4
3
2
1
4
3
2
1
4
2
1
3
7
3
4
1
2
1
2
5
6
5
1
2
►Safety bolt is at the back of the open circle
holder.
►Fix it with a hand slightly after position
regulation.
Caution for Assembling Part name and Quantity Pillar Assembling
The followings are presented to prevent from possible
danger or damage, occurring in setting up or using the
product. So obserbe the caution.
The pillar and horizontal bar are manufactured with steel pipe.
If you drop them, especially from another large ones, you may get
feet hurt or damage bottoms. So take care of an accident.
1.The pillar will be fixed on ceilings
and bottoms.
2.When a hanger takes a fall, it
possibly makes a baby get hurt
or breaks other article. So pre-
vent from the kind of troubles.
3.As a warning for a fall, lean the
pillar over the wall. Don’t stand it
upright.
4.Check up safety(shaking, bolt
loose etc) for the time of using
the product.
Caution for Pillar Setting up
Don’t set up the pillar on a weak part of ceilings or bottoms. A
hanger possibly has a tumble.
Distinguishment of Upper and Below Part, and Setting Method
Upper part is slim and below part is big from the fastening func-
tion device. Set up below pillar toward bottoms and upper pillar
toward ceilings
►Upper pillar down to below when
you press the one touch button
after release safety bolt behind one
touch fixation device
Check up before disassembling
Check up before assembling
In case of broken fixation pin
Compare and check up composition and parts of the product
before assembling.
Assemble the product by inserting parts on the upper pillar
and the lower pillar in order of numbers.
Parts have different colours depending on products.
Rubber ring places and fixes parts, so insert one rubber
ring under one part without fail.
The rubber ring inserted under parts is not shown.
Upper fixation board (4 EA)
Lower fixation board (4 EA)
upper pillar
(28mm)
lower pillar
(32mm)
lower pillar
safety bolt
upper pillar
one touch
button
1
Upper Pillar (28mm)
Lower Pillar (32mm)
Upper and below Pillar (4 sets)
2
Hanger horizontal bar long (4 EA)
4
Open circle holder (8 EA)
5
Rubber O ring (8 EA)
6
Basket shelves holder (4 EA)
10
Pants hanger bar holder (2 EA)
9
Pants hanger bar (2 EA)
8
Pants hanger (10 EA)
13
Basket shelves (2 EA)
11
Rubber O ring (6 EA)
12
Safety bolt (4 EA)
Use for One touch fixation device
7
3
Safety bolt
Pillar 1 Pillar 2 Pillar 3 Pillar 4
Pull upper pillar longer
than 50cm and insert
the above parts in order
of numbers.
Open circle holder
Hanger horizontal
bar is inserted in
the open circle
holder.
Assemble is so
that holder home is
shown “U” shape.
one touch fixation device
You have to remove fixation pin at below one touch button
before assembling pillars.
one touch fixation device
one touch button
pin
►Sharp as a pin or needle
to push it into the bo-
ttom, fall into the pillar.
►Push the button and
then pull pin the down.
►After remove the pin,
just rubbish
One touch
fixation device
One touch
fixation device
3 1
3 5