RATTAN SQUARE User manual

SQUARE DINING TABLE
Page 1 of 6
Thank you for purchasing the SQUARE DINING TABLE. P ease read the instructions carefu y to ensure safe operation
of the product.
Size: W 100cm x D 100cm x H 72cm
Colour: Double Flat Grey
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required

SQUARE DINING TABLE
Page 2 of 6
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
•Due to the size of this product we recommend that it is assembled in the room intended for
use.
•When you are ready to start, make sure that you have the right tools, plenty of space and a
clean, dry area for assembly.
•Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent it from scratching.
•Check the pack and make sure you have all the parts listed.
•Ensure that this product is fully assembled as illustrated before use.
•Check all screws or bolts are tightened and inspect regularly.
•Tools not included.
WARNINGS
•This product should only be used on firm, level ground.
•Keep small parts out of reach of children.
•Make sure the legs remain in contact with the ground.
•Do not use power tools to construct this product.
•Do not tighten screws until fully assembled.
•Do not over tighten screws or bolts.
•Do not use this product if parts are missing, damaged or worn.
•Do not stand on the product.
CARE INFORMATION
•Never use scourers, abrasives or chemical cleaners.
•To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or
detergents as they can bleach or damage the product.

SQUARE DINING TABLE
Page 3 of 6
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The fittings pack contains small items that should be kept away from
small children.
Parts
A B C D
Description: Table top
Qty: 1
Description: Leg Panel
Qty: 2
Description: Short Panel
Qty: 2
Description: Glass Top
Qty: 1
E F G H
Description: Bolt M6x20
Qty: 4
Description: Bolt M6x40 Qty:
8
Description: M6 Hex Nut
Cap Qty: 12
Description: M6 Spring
Washer Qty: 4
I J K
Description:
M6 Washer
Qty: 12
Description: M6 Washer
Qty: 8
Description:
M6 Hex Wrench
Qty: 1

SQUARE DINING TABLE
Page 4 of 6
CAUTION: There are many small components used in the construction of this product.
Please keep these components away from young children whilst assembling this product.
If you keep the fittings in a bowl during assembly you will be less likely to lose them!
Hints and Tips
Layout Parts on Soft Surface
Lay out all parts on a soft surface i.e. Rug, Carpet or Packaging Carton

SQUARE DINING TABLE
Page 5 of 6
STEP 1
Parts Required
NOTE: Only tighten bolts halfway
A. Table Top x1
B. Leg Panel x2
C. Short Panel x2
E. Bolt M6x20 x4
F. Bolt M6x40 x8
G. M6 Hex Nut Cap
x12
H. M6 Spring Washer
x4
I. M6 Washer x12
J. M6 Washer x8
STEP 2
Parts Required
Note: Adjust the balance of the table. Then tighten all bolts to 100%.
Install Glass top onto the top of the table.
Assembled Result
from STEP1
D. Glass top x1

SQUARE DINING TABLE
Page 6 of 6
Complete Assembly
Your SQUARE DINING TABLE is now completely assembled.
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the connectors are tight and secure.
Keep instructions for future reference