Hidrotek Snowpad User manual
SNOWPAD REVERSE OSMOSIS GUIDE
Ver 2-2023
Capacity 1.2l/min
1st stage Pp Spun filter
2nd stage Block Carbon filter
3rd stage Membrane with NSF certification
4th stage Post Carbon Filter
Cartridge lifespan 2000L
Dimensions (H x
W x D) cm
40 x 10.6 x 45.5
HOME INSTALLATION
REQUIREMENTS
INSTALLATION
GUIDE
REPLACEMENT OF
FILTERS
PROCEDURE
FILTERS
DISCONNECTION
PROCEDURE
SNOWPAD REVERSE OSMOSIS GUIDE
Ver 2-2023
INSTALLATION PROCEDURE
Tools Required:
Cutter
Adjustable
spanner
Teflon tape
Cordless drill
¼” drill
Cutting and Connection of pipes video:
https://youtu.be/FOr0oXXZkZ8
HOME INSTALLATION
REQUIREMENTS
INSTALLATION
GUIDE
REPLACEMENT OF
FILTERS
PROCEDURE
FILTERS
DISCONNECTION
PROCEDURE
SNOWPAD REVERSE OSMOSIS GUIDE
Ver 2-2023
INSTALLATION PROCEDURE
Installing the feed water tap:
1..Install Tee Fitting and Feed Water Valve as per diagram.
2..Wrap threads of Feed Water Valve and Tee Fitting with Teflon
tape.
3..Connect White Feed Water Tubing from unit to Feed Water Valve.
4..Install the Feed water valve Tee fitting, and then connect to
source water.
NOTE: Use only a supply as Feed Water, hot water will damage your
unit. Softened Feed Water will extend the life of the RO Membrane ·
Installing the feed water tap video:
https://youtu.be/WewK8S1kqQs
HOME INSTALLATION
REQUIREMENTS
INSTALLATION
GUIDE
REPLACEMENT OF
FILTERS
PROCEDURE
FILTERS
DISCONNECTION
PROCEDURE
SNOWPAD REVERSE OSMOSIS GUIDE
Ver 2-2023
INSTALLATION PROCEDURE
Installing goose faucet:
1..Select a convenient location near your sink to place the faucet.
2..Drill a hole 12mm in diameter in counter top.
3..Place washers, plates, seals and nuts in order as per diagram and
tighten on to counter
4.. Attach Blue Pure Water tubing to the bottom of faucet and
connect tubing to unit.
CAUTION: Check that tubing is
connected correctly.
Installing goose faucet video:
https://youtu.be/_TRsZ9VapjE
Installing the RO pipe to
the goose faucet:
HOME INSTALLATION
REQUIREMENTS
INSTALLATION
GUIDE
REPLACEMENT OF
FILTERS
PROCEDURE
FILTERS
DISCONNECTION
PROCEDURE
SNOWPAD REVERSE OSMOSIS GUIDE
Ver 2-2023
INSTALLATION PROCEDURE
Installing drain clamp:
1..Place drain clamp on drain pipe above the drain trap and
tighten securely.
2..Using the drain clamp as a guide, drill a 6mm hole, enough for
the 1/4” tubing to pass through one side of the drain pipe.
DO NOT drill through both sides.
3..Connect Red Waste Water tubing from unit to Drain Clamp.
CAUTION: When cutting the tubing, make it clean, square. cuts ,failing to
do so result in poor connection and possible leaks.
The lowest point of the line should be the point of connection to the Drain
Clamp.
There should be no sag in the line as this may cause excessive noise as the
reject water is owing to drain.
Installing video of drain clamp saddle:
https://youtu.be/zOsRXLczMWU
HOME INSTALLATION
REQUIREMENTS
INSTALLATION
GUIDE
REPLACEMENT OF
FILTERS
PROCEDURE
FILTERS
DISCONNECTION
PROCEDURE
Popular Water Filtration System manuals by other brands
Hydro International
Hydro International Up-Flo Operation and maintenance manual
Boneco
Boneco Aqua Pro A250 manual
Baldor
Baldor Dodge SLEEVOIL instruction manual
Acuva
Acuva Arrow 5 Owner's Product Manual
INTELLICLEAR
INTELLICLEAR 800 user manual
3M
3M Aqua-Pure AP430SS Installation and operating instructions
