HIGH ONE CH 60 W 302C User manual

MADE IN PRC
ELECTRO DEPOT
1 route de Vendeville
59155 FACHES-THUMESNIL
FRANCE
EN
WARRANTY CONDITION
This product has a 2-year warranty as of the date of purchase*, covering any fault resulting from
a manufacturing or material defect. This warranty does not cover defects or damage resulting
from incorrect installation, improper use or abnormal wear of the appliance.
*upon presentation of the sales receipt.
FR
CONDITION DE GARANTIE
Ce produit est garanti pour une période de 2 ans à partir de la date d’achat*, contre toute
défaillance résultant d’un vice de fabrication ou de matériau. Cette garantie ne couvre pas les
vices ou les dommages résultant d’une mauvaise installation, d’une utilisation incorrecte ou
de l’usure anormale du produit.
*sur présentation du ticket de caisse.
NL
GARANTIEVOORWAARDEN
Dit product wordt gegarandeerd voor een periode van 2 jaar vanaf de aankoopdatum*, voor
elke storing die het gevolg is van een fabricagefout of het materiaal. Gebreken of schade door
slechte installatie, onjuist gebruik of abnormale slijtage van het product worden niet gedekt
door deze garantie.
*op vertoon van kassabon.
ES
CONDICIONES DE GARANTÍA
El certificado de garantía de este producto tiene una duración de 2 años a partir de la fecha de
compra* que se limita a los defectos de fabricación y averías del material. Se excluyen de la
garantía deficiencias o daños originados por una mala instalación, errores en la manipulación
o por un uso inadecuado.
*previa presentación del comprobante de compra.

978333 - CH 60 W 302C
978334 - CH 60 K 302C
978335 - CH 60 S 302C
2/2 03/2023-V2
Cooker Hood
Hotte aspirante
Dampkap
Campana extractora
INSTRUCTIONS FOR USE .....................02
CONSIGNES D'UTILISATION .....................18
GEBRUIKSAANWIJZINGEN .....................34
INSTRUCCIONES DE USO .....................50

2 FR2 EN
Thanks!
Thank you for choosing this HIGHONE product.
Chosen, tested and recommended by ELECTRO DEPOT,
the products of the HIGHONE brand are easy to use,
reliable and of an impeccable standard.
Thanks to this appliance, you can be sure that each
use will bring you satisfaction.
Welcome to ELECTRO DEPOT.
Visit our website: www.electrodepot.fr

3FR
Aperçu de l’appareil
A
3 EN
Table of contents
AUsing the appliance
BUseful information Troubleshooting
Cleaning and maintenance
Installing with external opening
Installing without external opening
Start using your cooker hood

4EN
Using the appliance
A
Installation with external opening
If you have an outlet to the outside, your cooker hood can be connected as below picture by
means of an extraction duct (enamel, aluminum, flexible pipe or nonflammable material with
an interior diameter of 120mm).
1. Before installation, turn the unit off and unplug it from the outlet.
2. The cooker hoods should be placed at a distance of 65-75cm from the cooking surface for
best effect. See Pic 1.
3. To install onto the wall, drill 4 holes of Ø 8mm at a suitable place according to the centre
distance of the holes in the back of the cooker hood. See Pic 2.
4. Insert the wall plugs into the holes.
5. Insert the ST4*30mm screws into the wall plugs and tighten.
6. Put up the cooker hood onto the fixed screws.
7. Use the attached accessories enclosed to turn the safety screws into the two holes inside

5EN
Using the appliance
A
the hood, and then fix the screws to tighten the hood onto the wall. See pic below.
8. Put the expansion pipe on the outlet, then lead it outdoors, or use the outlet cover to seal
the outer outlet and open the inner exhaust valve. Note: the expansion pipe is not included
in the product.
Method B:
1. Drill 4 holes of Ø 6mm at the bottom of the hanging cupboard. See pic below.
2. Install the cooker hood on the bottom of the cupboard, tighten the cooker hood with the
included M4 screws + flat washers.

6EN
Using the appliance
A
3. Put the expansion pipe on the outlet, then lead it outdoors.
NOTE
The expansion pipe is not included in the product.
Noice: There are 2 methods for ventilation, including ‘ horizontal ventilation’ and ‘vertical
ventilation’. Pay attention to the ventilation method when installing.
Horizontal ventilation: See Pic A, please use a tool to knock out the outlet cover on the top,
then the air can be vented from the top.
Vertical ventilation: See Pic B, please use a tool to knock out the outlet cover on the back,
then the air can be vented from the back.

7EN
Using the appliance
A
Recycling version
Contact your supplier to obtain active carbon
filters to transform the extractor hood into
a recycling hood.
Installing the active carbon filter (cassette)
• Check that the diameter of the active
carbon filter corresponds the outlet
diameter.
• If necessary, remove the pre-installed
diameter adapter.
• Position the active carbon filter on the
outlet and attach it in place by turning
anticlockwise.
Installing the active carbon filter (cut-out)
• The metal filter has to be removed be-
fore the active carbon filter is installed.
• To open the metal filter, press on
the locking device and pull the filter
downwards.
• Place the precut filter on top of the
metal filter. Hold in position using the
metal rods (supplied according to the
model).
• Replace the metal filter in its original
position.
Installing without external opening
NOTE
Make sure that the filter is properly attached; otherwise it
could become dislodged and cause a hazard.
The installation of a carbon filter reduces the extraction
power of the hood.

8EN
Using the appliance
A
Air ventilation setting
Outdoor air ventilation: Turn the adjuster to the outdoor position (pic A), install the outlet, turn
on the cooker hood, then the air will be vented from the outside outlet.
Indoor air ventilation: Turn the adjuster to the indoor position (pic B), install the outlet cover,
turn on the cooker hood, then the air can be vented from the inside outlet.
WARNING
For safety reason, use only the same size of fixing or
mounting screws which are recommended in this instruction
manual.
Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards.

9EN
Using the appliance
A
Start using your cooker hood
Toggle switch
There are 3 speeds for the motor and on / off switch for the lamp.
Slide the switch for operation.
Motor Operation
0Off
1Low Power Setting
2Mid Power Setting
3High Power Setting
Light Operation
0Off
1On

10 EN
Useful information
B
Troubleshooting
Fault Possible Cause Solution
Light on, but motor
does not work
Fan switch turned off Select a fan switch position.
Fan switch failed Contact service center.
Motor failed Contact service center.
Light does not work,
motor does not work
House fuses blown Reset/Replace fuses.
Mains power cable is
loose or disconnected
Refit mains power cable to power
outlet.
Switch power outlet on.
Oil leakage
One way valve and the
outlet are not tightly
sealed
Take down the one way valve and seal
with sealant.
Leakage from the
connection of chimney
and cover
Take chimney down and seal.
Lights not working Broken or faulty bulbs Replace blubs as per this instruction.
Insufficient suction
The distance between
the cooker hood and the
gas top is too far
Refit the cooker hood to the correct
distance.
The Cooker hood
inclines
The fixing screw is not
tight enough
Tighten the hanging screw and make
it horizontal.
NOTE
Any electrical repairs to this appliance must conform to
your local, state and federal laws. Please contact the service
centre if in any doubt before undertaking any of the above.
Always disconnect the unit from the power source when
opening the unit.

11 EN
Useful information
B
Cleaning and maintenance
CAUTION
Before maintenance or cleaning is carried out, the cooker
hood should be disconnected from the mains power supply.
Ensure that the cooker hood is switched off at the wall
socket and the plug removed.
External surfaces are susceptible to scratches and
abrasions, so follow the cleaning instructions to ensure
the best possible result is achieved without damage.
General
Cleaning and maintenance should be carried out with the
appliance cold especially when cleaning. Avoid leaving
alkaline or acid substances (lemon juice, vinegar etc.) ont
he surfaces.
Stainless steel
The stainless steel must be cleaned regularly (e.G.Weekly)
to ensure a long life expectancy. Dry with a clean soft cloth.
A specialized stainless steel cleaning fluid may be used.
NOTE
Ensure that wiping is done along with the grain of the
stainless steel to prevent any unsightly crisscross scratching
patterns from appearing.
Control panel surface
The inlay control panel can be cleaned using warm soapy
water. Ensure the cloth is clean and well wrung before

12 EN
Useful information
B
cleaning. Use a dry soft cloth to remove any excess moisture
left after cleaning.
IMPORTANT
Using neutral detergents and avoid using harsh cleaning
chemicals, strong household detergents or products
containing abrasives,as this will affect the appearance of
the appliance and potentially remove any printing of artwork
on the control panel and will void manufactures warrantee.
Grease mesh filters
The mesh filters can be cleaned by hand. Soak them for about
3 minute in water with a mild detergent and then brush it
gently with a soft brush. Do not apply too much pressure so
as to avoid any damage to it . (Leave to dry naturally out of
direct sunlight.)
Filters should be washed separately to crockery and kitchen
utensils. It is advisable not to use rinse aid.
Removing grease mesh filters
1.
Push the grease mesh filter buckles forward and remove
the front of the filters.
2.
Then push the left or right lower side stops of the filter
up until the hanging point at one side stop is not hanging
the hood cavity.
3. Finally,take the whole mesh filters away.

13 EN
Useful information
B
Installing grease mesh filters
To install filters for the following four steps .
- Angle the filter into the slots at the back of the hood.
- Push the button on the handle of the filter.
- Release the handle once the filter fits into a resting position.
- Repeat to install all filters.
Carbon filter-not supplied
Activated carbon filter can be used to trap odors. Normally
the activated carbon filter should be changed every 3 to 6
months according to your cooking habit. The installation
procedure of activated carbon filter is as below.
1. Remove the grease filter.
2.
Take away the filter cloth from the back of the grease filter.
3. Fix the carbon filter on the back of the grease filter with
the small steel wire.
4. Reinstall the grease filter.
5. Use carbon filters for recirculation mode only.