HIGHLEAD GC22618 Instruction Manual
®
Purchasing
Dept
Copy
HIGHLEAD
GC22618
CYLINDER-BED UNISON FEED
SEWING
MACHINE
Instruction Manual
Parts
Catalog
SHANGHAI HUIGONG
N0.3
SEWING
MACHINE
FACTORY
CONTENTS
INSTRUCTION MANUAL
1, PRECAUTIONS BEFORE STARTING OPERATION....................................................................................l
2,
SPECIFICATIONS ....................................................................................................................................... 1
3,
PRECAUTIONS FOR SEWING OPERATE .................................................................................................2
4,
NEEDLE .........................................................................................................................................................3
5,
WINDING THE LOWER THREAD ............................................................................................................3
6,
ADJUSTING OF THE BOBBIN WINDER ...................................................................................................4
7,
REMOVING AND INSERTING THE BOBBIN ...........................................................................................4
8,
THREADING .................................................................................................................................................4
9,
ADJUSTING
OF
THREAD TENSION .........................................................................................................5
10, ADJUSTING THE PRESSURE OF PRESSER FOOT ..............................................................................6
11, STITCH LENGTH & REVERSING LEVER ...........................................................................................6
12, ADJUSTING THE LIFT OF THE ALTERNATING PRESSER FOOT .......................................................6
13, RE-SET THE SAFETY CLUTCH MECHANISM ......................................................................................7
14, ADJUSTING THE HEIGHT OF THE FEED DOG ...................................................................................7
15, RELATIVE POSITION OF THE FEED DOG
TO
NEEDLE PLATE .........................................................7
16, ADJUSTING THE HEIGHT OF THE NEEDLE BAR ................................................................................8
17, ADJUSTING THE HEIGHT OF THE PRESSER FOOT ..........................................................................8
18, TIMINGOFTHEVIBRATINGPRESSERFOOT ....................................................................................9
19, ADJUSTING THE THREAD TAKE-UP SPRING ......................................................................................9
CATALOG
A,
ARM BED AND
ITS
ACCESSORIES ......................................................................................................
10
B,
TAKE-UP THREAD AND ARM SHAFT MECHANISM ........................................................................
13
C ROTATING HOOK SHAFT MECHANISM ...............................................................................................
15
D,
FEEDING AND FEED LIFTING MECHANISM ....................................................................................
18
E,
STITCH REGULATOR MECHANISM ....................................................................................................20
F,
NEEDLE BAR FEEDING MECHANISM ..............................................................................................22
G,
PRESSER FOOTMECHANISM ............................................................................................................
25
H,
ACCESSORIES .........................................................................................................................................27
-1-
1,
PRECAUTIONS BEFORE STARTING OPERATION
1) Safety precautions
(
1)
When
turning
the power
on,
keep
your bands
and
:fingers
away
from
the
area around/under
the
needle
and
the
area
around
the
pulley.
(2)
Power
must
be
turned
offwhen
the
machine
is
not in
use,
or
when
the
operator leaves
the
seat
(3)
Power
must be turned
off
when tilting
the
machine
head,
installing or removing
the
"V" belt, adjusting
the
machine,
or
when
replacing.
(4)
Avoid
placing
fingers,
hairs, bars
etc.,
near
the
pulley,
"V" belt, bobbin winder
pulley,
or
motor
when
the·rnachine
is
in
operation.
(5)
Do
not
insert
fingers
into
the
thread
take-up
cover,
under/around the needle, or pulley when
the
machine
is
in
operation.
(
6)
If
a belt
cover,
finger
guard,
eye
guard
are
installed,
do
not operate
the
machine without
these
safety
devices.
2)
Precautions before starting operation
(1)
If
the
machine's oil pan
has
an
oil
sump,
never
operate
the
machine
before
filling
it.
(2)
If
the
machine
is
lubricated by a
drop
oiled (consider revising),
never
operate
the
machine
before
lubricating.
(3)
When
a new sewing machine
is
first
turned
on,
verify
the
rotational direction
of
the
pulley
with
the
power
on.
(The
pulley
should
rotate
counterclockwise
when
viewed
from
the
pulley)
(4)
Verify
the
voltage
and
(single
or
three)
phase
with
those
given
on
the
machine
nameplate.
3) Precautions for operating conditions
(
1)
Avoid
using the machine at abnormally
high
temperatures (35'C or higher)
or
low temperatures (5
'C
or
lower) .
(2)
Avoid
using
the
machine
in
dusty
conditions.
2_,
SPECIFICATIONS
Max.
Sewing
Speed
2200rpm
Max.
Stitch
Length
Smm
Thread
Take-up
Lever
Stroke
61.Smm
Needle Bar
Stroke
33.4mm
Presser
Foot
Stroke
By
Hand
8mm
By
Knee
14mm
Alternating
Movement
Lifting
Presser
Foot
4.3mm
Needle DPX
17
22#
Rotating
Hook
KRT31-11SG
Lubrication System
Manual
Electric Machinery 1400rpm370W
-1-
3...
PRECAUTIONS
FOR
SEWING OPERATE
1)
Cleaning the machine
Before leaving the factory, the machine parts are coated with rust-preventive grease, which may
be
hardened and contaminated
by
dust during storage and shipment
This
grease nmst
l;>e
removed with
gasoline.
2) Examination
Though every machine
is
confirmed
by
strict inspection and test before leaving the factory, the
machine parts may
be
loosen or deformed after long distance transportation with
jolt
A thorough
examination must
be
perfo1med after cleaning the machine. Turn the balance wheel to see
if
there
is
running obstruction, parts collision, uneven resistance or abnormal
no~.
If
these exist, adjustment must
be
made accordinglybefore run-in operation.
3) Lubrication
(Fig.1...
Fig.2...
Fig.3, Fig.4)
When a new sewing machine is first operated, or when a sewing machine
is
operated which
is
out
of
use
for
long period
of
tiine, it will
be
necessary
to
oil through the oil holes after removing the rubber plugs
shown
below.
For oil, Use white spindle oil
Fig.1 Fig.2
B
Fig.3 Fig.4
-2-
4)'Broken-in
It
is
imperative that for the first several weeks
of
operation the max. Speed is held at less than
l600rprninorder
to
allow the parts
to
become properlybroken-in.
4..
NEEDLE (Fig.5)
Use DPX
17
#22. The size
of
the needle to
be
used should
be
determined
by
the size
of
the thread, which must
pass freely through the eye
of
the needle.
1)
Removing the needle
bar
to the
highestposition:
2) Loosen the needle screw, insert
the needle up to the
bottom
of
needle
clamp.
Keep the long groove side
of
needle forward the left.
3) Tighten the screw.
Needle
bar
Long groove
facing to the
left
5,
WINDING
THE
LOWER
THREAD (Fig.6)
1)
Push a bobbin
on
thebobbinwinder spindle (3) as far
as
it
will
go.
Needle screw
Needle
Fig.5
2) Pass the thread from the thread stand downward through the eye (1) in the teiision bracket, then
between and around the back
of
the tension disc (2).
3) Bring the thread foiward toward the
bobbin and wind from
blow
in
clockwise
direction several
times
around the bobbin.
4) Push the lever (4) toward other side
so that the pulley and V
belt
will engage and
then start the machine.
5) The pulley will automatically
be
free
from the belt and stopped after the bobbin
is
filled with thread.
Fig.6
-3-
6,
ADJUSTING THE BOBBIN WINDER (Fig.6)
1)
In
case
of
uneven
winding
Loosen the screw (5) inthe tension bracket and move the bracket to the right
or
to the left
as
may be
required.
2) Winding
amount
of
thread
Adjustment screw (
6)
can be turned
in
or out to increase or
to
decrease the amount
of
thread wound
on
the bobbin.
3) Winding
strength
Strength
of
the winding can be adjusted with the nut (
7)
7,
REMOVINGAND INSERTING THE BOBBIN (Fig.7)
1) Take out
the
bobbin
Open the cover and take out the bobbin.
2) Install
the
bobbin
Replace the bobbin to the bobbin case;
pull the thread
to
the left.
8,
THREADING (Fig.8)
Raise the needle bar
to
its highest position
and thread the upper thread in the following
order.
Fig.8
-4-
Fig.7
9...
ADJUSTING
OF
THREAD TENSION (Fig.9)
For
ordinary
stitching.
the
tension
of
the
upper
and
the
lower
threads
should
be equal
1) Tension
of
upper
thread
(Fig.10)
Before
adjusting
the
tension
of
the upper
thread,
it
should
certain that the presser
foot
is
let
down
but
not in other position.
To
adjust tension, turn serrated nut
on
tension device to the right
to
increase tension
and
to
the
left
if
you
desire to decrease
it
Well balanced stitch
Upper thread
is
too strong
or
lower thread is too weak
Lower thread
is
too strong or
upperthread
is
too weak
Fig.9
2) Tension
of
the
lower
thread
(Fig.11)
Fig.10
Turning
the
larger screw
(A)
to
the
right
(clockwise)
will increase
the
thread
tension,
while
turning
it
to
the
left
(counter-clockwise)
will decrease
it.
Thread
tension
spring
Fig.11
-5-
1
O..
ADJUSTING THE PRESSURE
OF
PRESSER
FOOT
(Fig.12)
Pressure
of
the presser foot can be adjusted
by
turning the pressure regulating thumb screw
(A)
To
increase the pressure, turnthe screw to the right and to left
if
you decrease the pressure.
11..
STITCH LENGTH & REVERSING LEVER (Fig.13)
Adjusting the stitch adjustment
bar
can set stitch length
For desired stitch length, push the
stitch adjustment
bar
downward.
12,ADJUSTING THE LIFT
OF THE ALTERNATING
PRESSER FOOT(Fig.14)
To
alter lift, loosen the wing nut (1) and
move the link and stud assembly along the
slot-move up to raise the feeding presser foot
and push down
to
lower this foot. Tight wing
nut upon completion
of
adjustment.
-6-
Fig.12
Fig.13
Fig.14
13, RE-SET
THE
SAFETYCLUTCH MECHANISM (Fig.15)
1) Retmving
any
foreign matter may have lodged itselfin
the
hook.
Do
notuse any sharp-edged
tools.
2) Depress button
CD)
, turn the pulley clockwise until
the
locking mechanismre-engages.
Fig.15
14, ADJUSTING
THE
HEIGHT
OF
THE FEED DOG (Fig.16)
The
max.
Height
of
the
feed
dog
from
the surface
to
the
needle plate
is
normally 1nnn
To
adjust
this
height:
1)
Set
the
stitch length at
mininnun.
2)
Turn
the
pulley
so
as
to
raise
the
feed
dog
to
ithighest position.
3)
Take
out
cover
(1) , Loosen
the
screw C
2)
, adjust
the
height
of
the
feed
dog.
4)
Tighten
the
screw (
2)
after
adjustment.
2
1
Imm
Fig.16
-7-
15
..
RELATIVE POSITION
OF
THE FEED DOG
TO
NEEDLE PLATE
(Fig.17)
1) Set the stitch length at
minimum.
2) Tum the pulley so as to raise the
feed dog to its highest point.
3) Lay
down
the machine head toward
the other side, loosen the screw (E).
4) Adjust the needle plate to the center
of
the needle hole on the feed dog.
5) Tighten the screw.
·
16
..
ADJUSTING THE HEIGHT OF THE NEEDLE BAR(Fig.18)
When the needle
bar
is at its highest
position, normally the measurement between
the surface
of
the needle plate and the upper
end
of
the needle eye is 22.3mm.
To
adjust
this, loosen screw (
B)
(Fig.3), and raise
or
lower the needle
bar
as may
be
required.
Then tighten the screw.
22.3nun
Fig.17
r----''---.......c::::~----.-1
Fig.18
17..
ADJUSTING THE HEIGHT OF THE PRESSER FOOT (Fig.19)
1)
Adjustment by the presser
bar
lifter
Loosen the screw (1), raise the presser
bar
lifter and loosen the setscrew (2), move the lifting presser
foot up
or
down as may
be
required so as to getthe correct height and tighten screws.
2)
Adjusting the lift
of
alternating presser foot
If
the height
of
the lifting presser foot changes, the momentums
of
the
lifting and vibrating presser foot
vary, thus the height
of
the
vibrating presser foot must be adjusted. Lower the presser
bar
lifter, holding the
vibrating presser foot and loosen the screw (3) and move the presser foot
up
or
down as may be required.
After setting the position, tighten the screw.
-8-
r------------~----·------------~
1 5 4 3
Fig.19
18
..
TIMING
OF
TH·E VIBRATING PRESSER
FOOT
(Fig.19)
This is the normal timing when
turn
the pulley toward you, after lowing the presser bar lifter, the vibrating
presser foot should reach the feed dog earlier than the needle eye comes to, and when the needle raises, the
vibrating presser foot should leave the feed dog after the needle eye has left the feed dog. This is due the reason
that the vibrating presser foot must tightly hold the goods while the needle
is
passing the goods for avoiding
irregular stitches.
To
adjust this, set the lift
of
the alternating presser feet to equal, loosen the two screws (
4)
and
adjust the rotating position
of
the camfaster or slower
as
may be desired, and tighten the screws.
19
..
ADJUSTING
THE
THREAD
TAKE-UP
SPRING
(Fig.20)
Normally, the thread take-up spring
(I
) should hold slack
of
the upper thread until the needle reaches to the
goods, and it should pause while raising
of
the needle and passing the upper thread through the bobbin case.
1)
For
more control action
-on
the thread
Loosen the stop screw (2), move
the. stop (3) to the right (for less action,
move to left). Tighten the screw.
2)
To
adjust the tension spring
Loosen the nut (4) and screw (5),
turn the tension stud (6) slightly
to
the
left to strengthen the tension (to lighten
the tension, turn to the right) with a
screw driver. Tighten the screw and nut
upon completion
of
adjustment.
-9-
Fig.20
3 2
A.
ARM BED AND ITS ACCESSORIES
20
19
18~
----------------
6 -------
------~
---
17
----------
15
14
10
3----
2------
63
62
61
26
27
28
29
30
31
32
33
34
35
36
38
39
40
\r------~~~~-----41
------------42
·~---------~43
·-----------44
i----------45
----------46
'1----------47
!
60
59 58
57
-
10
-
A. ARM BED AND ITS ACCESSORIES
Fig.
Part.N!J.
Description
Pcs.
Remarks
No.·
AOl
HA500C2070 Screw 1 SM9/64
(40)
x5
A02 H3108B0691 Thread guide 1
A03 H3108B0692 Felt 1
A04 HA106B0676 Screw 1 SM9/64
(40)
x6
A05 HA106B0675 Thread guide 1
A06 H2400B2080 Screw 2
SM3/l6
(28)
X13
A07 H2400B2070 Thread guide 1
A08 H605030100 Stop plate pin 2
GB!fll9.2
3x10
A09 H4100B2260 Screw 2 SM3/16
(28)
xlO
AlO H4122B0068 Cover 1
All
H4100B2240 Stop plate l
A12 H4100B2250 Needle plate 1
A13 H4100B2180 Screw 2 SM9/64
(40)
X8.2
A14 H4100B2220 Needle guide plate (right) 1
A15
H2400B2060 Plate for oil guard 1
A16 HA300B2170 Screw 3
A17 H3106B0671 Face plate 1
A18 H2400B2050 Oil guard 1
A19 H3100B2060 Thread take-up guard 1
A20 HA300B2160 Screw 1
SMll/64
(40)
XlQ
A21
H4100B2110 Screw 6
SMl/4
(24)
x9.8
A22 H4100B2100 Hinge 1
A23
HA300B2170
Arm
side cover screw 4
A24 H4100B2150
Arm
side cover 1
A25
HA307B0674 Rubber plug 3
<I>
11.8
A2(;i
H2400J2010 Oil wick 2
A27 H4105B0022
Arm
1
A28 H2400J2020 Oil cap 2
A29 HA700B2060 Screw 2
SMll/64
(40)
x8
A30 H2400B2100 Thread guide 1
A31
H4123B0069 Slide plate 1
A32 H4100B2180 Screw 4 SM9/64
(40)
x8.2
A33
H4106B0662
Arm
bed 1
A34 H4100B2060 Link plate 1
A35
H4100B2050 Oil reservior 1
A36 H4107B0672 Supporter l
A37 H4100B2070 Screw 1
SMI/4
(24)
x5.7
A38
H4100B2090 Washer 1
A39 H4100B2080 Screw 1
SMl/4
(24)
x20
A40 H4100B2210 Needle guide plate (left) 1
A41
H3100G2230 Thread tension releasing pin 1
A42 H2504C6510 Screw 2 SM9/64
(40)
x3
A43
H3111B0704 Tension releasing plate 1
-
11
-
A.
ARM BED AND ITS ACCESSORIES
Fig.
Part
No.
Description
Pcs.
Remarks
No.
A44 H3111B0705 Tension releasing spring 1
A45 H3100B2070 Three-hole thread guide 1
A46 HA7311C606 Screw 1
SMll/64
(40)
x12
A47
H31611Blll
Mounting plate 1
A48 H2504C0121 Thread tension releasing pin 1
A49 H31611B211 Tension bracket pin 1
A50 H2504C0013 Screw 1
SMll/64
C32)
x7
A51
H2504C0657 Thread tension disk 1
A52 HA310B0701 Thumb nut
...
1
A53 HA115B7010 Stop disk 1
A54 HA607B0068 Thread tension spring 1
A55 H2504C0656 Thread tension disk 2
A56 H2504C0658 Thumb n\lt 1
SMl/4
(
40)
x4.5
A57 H3111B0703 Screw 1 SM3/32
(56)
x6
A58 H2504C0654 Thread controller disc 1
A59 H3221B6819 Spring stop 1
A60 H32481BC21 Screw 1 SM9/64 (
40)
x6
A61
H3111B0702 Thread take-up spring 1
A62 H31611B311 Screw 1
SMl/4
(40)
xl0.5
A63 HA300B2080 Screw 1 SM15/64
(28)
x6.8
-
12
-
B. TAKE-UP THREAD AND ARM SHAFT MECHANISM
36-------
35-
~.
31
30
29
28
27 26 25 24
23
-
13
-
----------------
22
14
15
B.
TAKE-UP THREAD AND ARM SHAFT MECHANISM
Fig.
Part
No.
Description
Pcs.
Remarks
No.
BOl
H2009B0742 Felt 1
B02 H2009B0743 Felt 1
B03 H31133Bl04
Ann
shaft bushing (left) 1
B04 HA100C2020 Screw 1 SM15/64
(28)
xlO
B05 H31122B104 Felt 1
B06 H4105C0661
Ann
shaft bushing (middle) 1
B07
HAIOOC2020
Screw 2 SM15/64
(28)
xlO
BOS
HA10800661 Collar for rum shaft 1
B09 HA105D0662 Screw 2
SMl/4
(40)
X4
BlO H3200C2030 Belt 1
Bll
H4100C2030
Ann
shaft 1
B12 HA100F2130 Screw 1 SM15/64
(28)
x8
B13 H3205C1021 Pulley 1
B14 H3205J0662 Bear 1
B15 HA113F0684 Screw 2 SM15/64
(28)
X8.5
B16 HA110D0672 Screw 2 SM15/64
(28)
x12
B17 H4100C2040 Balance wheel 1
B18 H3205J0661
Ann
shaft bushing(right) 1
B19 H3205C0661 Spring washer 2
B20 HA113F0684 Screw 1 SM15/64
(28)
x8.5
B21
HAIOOC2060
Screw 1 SM9/32 (
28)
x
13
B22 H3100C2080 Oil wick 1
B23 HA105D0662 Screw 1
SMl/4
(40)
X4
B24 H4100C2050 Needle
bar
crank 1
B25 HA108C0663 Screw 1 SMl/4
(40)
X7
B26 HA100C2070 Screw 1 SM9/32
(28)
xIO
B27 H3200C2120 Oil wick 1
B28 H3200C2130 Oil packing stop screw 1
B29 H3100C2070 Hinge pin 1
B30 H24211D405 Oil wick 1
B31
H3100C2060 Thread take-up pin 1
B32 H2405Dl 112 Driving stud 1
B33 H2405Dl 122 Oil wick 1
B34
H2405Dllll
Thread take-up lever 1
B35 H2405Dl
121
Hinge pin 1
B36 HA110D0672 Screw 1 SM15/64
(28)
xl2
-14-
C. ROTATING HOOK SHAFT MECHANISM
14
13--
11--·
\ \
7 6 5 4 3
21
-15-
57 56
39
55
C.
ROTATING
HOOK
SHAFT MECHANISM
Fig.
Part
No.
Description
Pcs.
Remarks
No.
COl
H411l1El04
Feed lifting rock shaft crank 1
C02 H4104E0653 Slide block for crank 1
C03
HA106B0676 Screw 2 SM9/64
(40)
X6
C04 H4104C0652 Screw 1 Sl\113/64
(32)
x5
cos
H4104C0651 Feed eccentric 1
C06 H4104E0652 Feed rock shaft crank 1
C07 H41111E304 Feed dog 1
cos
H41111E404 Screw 1
SMll/64
(32)
x7
C09 H41111E204 Felt 1
ClO H4104C0653 Screw 1 SM13/64
(32)
x4.5
Cll
H4100D2080 Screw 1
SMl/4
(24)
X4.5
C12 H4108D0682 Screw 3 SM13/64
(32)
x6
C13
H4108D0681 Bevel gear for hook shaft 1
Cl4
H4105D0652 Screw 4 SM13/64
(32)
x3.5
C15
H4100D2060 Bevel gear for hook shaft 1
C16 H4100D2140 Screw 2 SM3/16
(28)
xtl
C17 H005001050 Washer 2
GB!f97.l
5
C18
H41611Dl16 Rotating hook bracket 1
Cl9
H41611D316 Felt 1
C20
H41611D216 Felt 1
C21
H410269Dl6 Guide plate 1
C22 H410270Dl6 Guide plate pin 1
C23
H41622D216 Guide plate slide block 1
C24
H4100D2180 Screw 1 SM9/64 (
40)
x
10
C25
H4114D0069 Rotating hook 1
C26 H2800I2020 Bobbin 1
C27
H4100D2120 Rotating position guide 1
C28
H2204C0651 Screw 1 SM9/64
(40)
x5
C29 H4105D0651 Collar for hook shaft 2
C30
H4100D2070 Hook shaft bushing {left) 1
C31
H4100D2090 Felt 1
C32 H4106D0661 Ratchet wheel 1
C33
HA108C0663 Screw 1
SMl/4
(40)
x7
C34 H601016100 Safe clutch shaft pin 1 GB!f91
t.6xto
C35
H4107D0673 Safe clutch shaft 1
C36 H4107D0672 Safe clutch spring 1
C37
H4107D0671 Safe clutch bushing 1
C38
H4100D2100 Hook shaft bushing(right) 1
C39 H4100D2010 Rotating hook shaft 1
C40
H4100D2080 Screw 1
SMl/4
(24)
x4.5
C41
H4106D0662 Screw 1
SMl/4
(40)
xs
C42 H4119D0717 Shaft for pulley 1
C43
HA104F0654 Screw 1 SM15/64
(28)
xtO
-16-
C. ROTATING HOOK SHAFT MECHANISM
Fig.
Part
No.
Description
Pcs.
Remarks
No.
C44 H4721D8001 Screw 1 SM15/64
(28)
x8.5
C45
H4722D8001 Pulley 1
C46 H4723D8001 Screw 2 SM15/64
(28)
x4.5
C47 H3205C0661 Spring washer 1
C48 H007013025 E-type ring 1 GB!f896
2.5
C49 H4716D8001 Spring for pulley 1
C50 H4718D8001 Pin 1
C51
· H4714D8001 Pin 1
C52 H4717D8001 Lever for pulley 1
C53 H4719D8001 Short lever for pulley 1
C54 HA106B0676 Screw 2 SM9/64
(40)
x6
C55
H4100D2170 Plate for pulley 1
C56 H4713D8001 Long lever for pulley 1
C57 H4715D8001 Link pin 1
-
17
-
Table of contents
Other HIGHLEAD Sewing Machine manuals
HIGHLEAD
HIGHLEAD HLK-1510 User manual
HIGHLEAD
HIGHLEAD GC0518 SERIES User manual
HIGHLEAD
HIGHLEAD GC0318-1A User manual
HIGHLEAD
HIGHLEAD GC20618 Series Instruction Manual
HIGHLEAD
HIGHLEAD GC20638 User manual
HIGHLEAD
HIGHLEAD GM288-3 User manual
HIGHLEAD
HIGHLEAD GM747-3 Instruction Manual
HIGHLEAD
HIGHLEAD GC24698-2B User manual
HIGHLEAD
HIGHLEAD GC24628-1 User manual
HIGHLEAD
HIGHLEAD GC20518 Series User manual
HIGHLEAD
HIGHLEAD GG0068-1 User manual
HIGHLEAD
HIGHLEAD GL13138-1 Instruction Manual
HIGHLEAD
HIGHLEAD GL13118-1 Instruction Manual
HIGHLEAD
HIGHLEAD GA2688-1 Instruction Manual
HIGHLEAD
HIGHLEAD GC0918-1-D User manual
HIGHLEAD
HIGHLEAD GC618-1 User manual
HIGHLEAD
HIGHLEAD GC20618 Series Instruction Manual
HIGHLEAD
HIGHLEAD GC1918 -MDZ User manual
HIGHLEAD
HIGHLEAD GC24818-1D User manual
HIGHLEAD
HIGHLEAD GC20638-25 User manual
