HIMO C26 User manual

E-Bike
Please read the instruction manual carefully before using your bike
Do not use the bike until you know its performance. Please keep the
instruction manual properly

Notes for using
According to the regulations on the implementation of the road traffic safety law of the People's Republic
of China, e-bike rider must be at least 16 years old.
When driving in the non-motorized lane, the maximum speed shall not exceed 15km/h;On roads
without non-motorized lanes, drive on the right side of the roadway.
Don't cause injury by lending your bike to someone who can't handle it.
Passengers or goods shall be carried according to laws and regulations.
Riding in rain and snow, the braking distance will be extended, pay attention to slow down;Avoid
traveling in bad weather such as heavy rain.
Before riding, check the braking system and clean the reflector to avoid blocking.
Obey traffic rules strictly
Safe of using the product
Please strictly abide by the traffic laws and regulations, prepare helmets, protective
equipment and other protective equipment before riding, and pay attention to driving
safety
Do not ride with one hand or two hands away from the handle.
Do not park in building doors, evacuation staircases, walkways, and safety exits.
Do not charge inside residential building and park, should be far from combustible when
charging, please charge according to regulation time, charging time should not be too long.
Correct use and maintenance of batteries, old batteries can not be disassembled without
authorization, should be organized by the professional departments recycling. Know how
to use charger and warning terms, use original charger.
When adjusting the saddle position, be careful not to expose the safety mark line of the
saddle tube.
Preparation before riding
Whether the power circuit and lighting are good.
Whether the front and rear brake lever are
good.
Whether the handlebars and front and
rear wheels are in a tight state.Whether the
tire pressure is normal.
Bike coding position
（The code at the bottom of frame）

Main technical parameters of the bike
Controller Spec.
Under voltage protection
Over current protection
Under the condition of full power, the endurance is 75kg, the temperature is about 25℃, the environment of
flat road is still without wind, and the driving condition is measured at 15km/h uniform speed under the
energy-saving mode. The actual endurance will be different due to factors such as load, temperature, wind
speed, road surface and operating habits.
Front and rear wheel center distance
Max weight
Maximum design speed
Assisting rang
Electric range
Consumes electricity（100KM）
Loading weight
Dimensions (L*W*H)
Battery Spec.
Lithium ion batteryBattery type
Capacity
Voltage
Motor Spec.
Brushless dc motor
Motor type
Rated power
Rated speed
Voltage
Brake sensor
Overspeed alarm
Electrical schematic
Motor
Controller
Booster sensor
Power signal
The cathode
The cathode
Head light signal
Head light
Knob
Battery
Charger port
5Acharging fuse
30A fuse
Display
Handle signal
The cathode
The cathode
The signal of handle The wire for lock of power
Power Power
Brake signal Head light signal Blank
The cathode
Overspeed warning signal

Get to know C26 quickly
(Wiggle the wheels to increase the bottom space for easier battery
installation and removal)
Battery mounting and locking
Battery out
Insert the key to open the battery lock,hold the battery with your hand and push
the safety clasp to remove the battery.(please be sure to hold the battery with
your hand when taking out the battery to avoid the accident of touching the ground)
1.Insert the key to rotate to the open state,put the battery into the
predetermined position of the body,push it upward until the machine
makes a clear sound and the battery is energized.
2.Push the battery safety buckle to the tight position.
3.Turn key to lock and pull out.(the key cannot be pulled out when the battery lock is open).
Security card buckle
Battery lock

Display and riding mode
Display introduction
Speed
Mileage accumulated
(switching)
Subtotal mileage
(switching) Headlight indication
Mode button
Switch button
Power indicator
Gear position indication
(power/medium speed/high speed)

The first default gear is "ECO" assisted cycling mode;
Pedal riding speed reaches 5KM/H;
Electric assist riding
Electric riding
Normal riding
Parking mode
Pedal riding
In the startup state;
Long press 3 seconds to switch
mode to "P",
Open parking mode.
Press the button to switch to the medium speed gear
of"MID" electric cycling mode;This mode can be started
by twisting the crank or the speed exceeds 5km/h.
Press the button to switch to the high-speed gear of
"HIGH" electric cycling mode;This mode can be
started by twisting the crank or the speed exceeds
5km/h.
Long press the button for 3 seconds to start the
electric bike;
Long press the key for 3 seconds to
close the electric bike;

Switch for the headlight
Mileage pattern
Long press button for 3 second to open the headlight
Long press button for 3 second to close the headlight
In the startup state;
Long press the key for 3 seconds to
close the electric bike;
Press button to switched between (TRIP) →
accumulated mileage (ODO)

Battery charging
First plug the power supply pin of the charger into the
charging port ofthe battery, and then plug the power
supply pin into the power supply.
Under charging state, the indicator light of charger is
red,and when fully charged, it is green.
Unplug the power plug after charging.
If the battery is charged in the bike, please turn off
the instrument power.
Daily charge
Soft cap
Charging port
Charger
Indicator light
Power supply pin
Power supply pin

Prepare 1 suitable phillips screwdriver, 2 no. 7 batteries.
Remove the rear lamp, unscrew the front panel screw, open the rear housing,
and replace the battery.
Buckle the rear shell, screw well, install it on the fixing plate, and
replace the battery.
Taillight is designed as an independent switch.
Press the switch when using.
Tail light
Rear reflector
Switch
Cross screwdriver
No.7 battery
2 pcs
Battery capacity button
Power indicato
When your battery is in the state of charging or not
charging, press the power display button to display
the current remaining power.
Check battery capacity
Taillight opening and maintenance Change battery

Transmission using
Transmission diagram
When using a speed change system, try not to skip gears, which can easily damage the transmission.It is not possible to change two gears at a time above,
should be a level of adjustment, can better protect the transmission system.
Do not reverse the transmission system when the bike stops running, or when it is going downhill. This will not only be bad for the transmission system, but also may
cause accidents.
If it is their transmission fault, or gear is not accurate situation, will affect the performance of the transmission, at this time should be timely to the professional
bike shop maintenance, in case of aggravation of the fault.
When using the transmission system, also pay attention to the following details
Gear Speed
Slow
Fast
Moderate
Power
Rlax
Moderate
Hard
To speed up, start with a lower gear and shift to a higher gear as you speed up
When going uphill, the speed will decrease,the gear will be lowered to maintain a certain pedal
strength
Downwind will speed up, increase gear to maintain a certain degree of pedal strength
Shift down
Gear pointer
Shift up The above is cycling advice, according to personal habits to reasonable use of gear

Damping adjustment
1.Shock absorber opening is suitable for abnormal uneven road surface.
2.Shock absorber lock applied to flat, long distance, uphill road.
When the road is in good condition or going uphill, we need to turn off the shock absorbers.
Otherwise, the shock absorbers will stretch up and down to absorb a large part of the force,
which will make riding more difficult.
3.Shock absorbers can be fine-tuned to the degree of hardness, along the
direction of the arrow slightly rotation.
Vibration absorber fine tuning can be more accurate to adapt to the different riding habits of the rider.
Shock absorber indicato on
The front fork is stretched up and down under the force, which can alleviate the impact of
the protrusion on the vehicle and the rider, better protect the bicycle parts, and make riding
more comfortable and easy to control.
Turn counterclockwise to open the shock absorber
Turn clockwise to lock the shock absorber

Description of component
Saddle
License plate intergral tail light
Seat post
Pedal
Kickstand
Gear system
Wheel light
Rear disc brake
Motor
Display
Hnadlebar
Charging port
Battery
Knob
Gear shifer
Head light
Suspension fork
Wheel light
Front disc brake

Before use, confirm that the battery model is the original battery of the whole bike, do not use any other brand of battery.
Check the appearance of lithium battery intact, no damage, leakage, heat and water, smoke and other obvious phenomena.
In order to ensure the safety of transportation, the battery's output power is about 30%. Due to the self-consumption during the transportation
and storage cycle, the battery is low or no electricity in the first use. This is a normal phenomenon.
About batteries
Note before use of lithium battery
The best operating environment is 10℃-45℃
At low temperature, available capacity of lithium battery will decrease to different degrees. The specific reference degree is as follows:
The available capacity is about 70% at -10℃, 85% at 0℃and 100% at 25℃.If the battery has odor, heat, deformation and other abnormal
conditions, please stop using immediately, away from the battery and contact the after-sales department.
The battery is not a part that can be repaired by the user. If there is any abnormal
phenomenon, please contact the after-sales department for maintenance.
Disassembling the battery without permission will not be covered by the three-pack
policy and may cause the battery to generate heat, smoke, fire or explosion.
Using the environment
Warning

Charger port of the battery
When the battery is placed on the bike, it will constantly consume the battery power. After the bike is placed for a period of time, the meter
shows that the decrease of the battery power is normal.
Please store the battery in the ambient temperature from 0℃to 25℃. Do not store the battery in an environment higher than 45℃,
or it will cause irreversible
capacity decay of the battery.If the bike is not in use for a long time (such as winter, summer or other special circumstances), the battery
must be taken out and stored separately and charged regularly. Otherwise, the battery may be completely exhausted and irreversible damage
may occur. For such problems, the battery fault will not be within the scope of three guarantee.
The best storage capacity for a battery is 50%. Long-term storage of less than 10% or more than 90% of the battery will lead to irreversible
capacity decay.
Avoid storing batteries in hazardous locations. Falling may cause uncontrolled damage to the battery interior and may cause battery leakage,
heat, smoke, fire, or explosion.
Storage environment
Use the original charger to charge the battery. Do not use other brand or model charger to charge the battery.
Please charge the battery at the ambient temperature of 10℃~ 40℃to ensure that there are no flammable substances around and
good ventilation.
Charging time indicates that if the charging time of the battery is less than 12 hours, overcharging will affect the battery life and there are
safety risks.
In the early stage of charging, the electric quantity rises quickly, while in the later stage, it is the procedure set for charging safety, which is the
normal situation.
When charging in winter, the outdoor temperature is relatively low. When the environment is below 0℃, the battery will stop charging.
This is a normal phenomenon.
Outdoor charging is strictly prohibited in bad weather.
During the charging process, the charger has a temperature rise effect, and the surface temperature is relatively high, which is a normal
phenomenon. Please feel free to use it, and pay attention to avoid children touching it.

Maintenance and repair
Whether the fastener is locked or not, whether the joints of all parts are normal:
Whether the tread pattern of the tire is worn and cracked, whether the front and rear tire pressure is appropriate,
Whether the drive system is smooth;
Whether the brake system is working properly.
Regular bike inspection
When this product is not in use for a long time, please do not store it in outdoor environment, under strong light
and below zero, and keep it at least 2m away from heat source (heating equipment, etc.).
Store in a dry, clean, well-ventilated indoor environment where the temperature is 10℃~ 45℃and the relative humidity is no more than 90%.
If you do not use the bike for a long time, pay attention to regular charging (generally about two months apart) to maintain battery performance;
This product should not contact with corrosive liquid to avoid any mechanical impact and heavy weight.
Bike storage method
Should not be subjected to severe mechanical impact, exposure to the sun, rain, chemical corrosive substances and harmful gases during
transportation；
During the process of loading and unloading, the products should be handled with care and be strictly protected against throwing, tumbling
and heavy weight.
The transportation

After-sales service
According to <Product quality of the People's Republic of China>&<Law of the People's Repulic of China on the
protection of user's right and interests>and the regulation of after sales service,the after sales service for HIMO
electric scooter is as below:
If the goods are rejected or intercepted due to non-quality reasons after shipment, the user shall bear the round-trip freight.
Within 7 days after receipt, because of quality problems, in the case of does not affect the goods in good condition (affect the situation of the
goods in good condition including but not limited to: guarantee certification and invoice lost, artificial damage, maintenance and protection
label damage, product appearance, or the outer packing damage, 10 km mileage super, the accessory missing accessories, etc.).Return
freight and wear and tear shall be borne by the customer.If the packaging is lost or damaged, the customer shall bear the original
packaging cost (excluding the packaging cost incurred by logistics during return).
If the goods are returned or replaced due to quality problems within 7 days after signing and receiving, the return freight shall be borne by
the merchant. Offline channel purchase products do not support seven days without reason return.
Free reason in return within 7 days
Do not flush with water to avoid the risk of accident caused by wet internal electronic components and wiring;
Please use neutral cleaner, wipe paint or plastic parts surface dirt with a cloth, and then use dry cloth to wipe;
Please use lubricating oil to wipe the metal parts of the bike body for maintenance;
Do not oil the brake parts to avoid causing brake failure and dangerous.
Maintenance and cleaning instructions

No return for cycling more than 100 km;
It can be replaced within 15 days due to quality problems;
Beyond 15 days, within the warranty period, can be repaired.
During the warranty period, HIMO official customer service center will provide you with free after-sales service.If the service period and scope of
"three guarantees" are exceeded, HIMO official customer service center will provide you with paid after-sales service according to the local market
situation and maintenance price.
If the product you purchased cannot drive due to quality problems, the HIMO official customer service center will provide you with maintenance
services.
The warranty period of online sold products shall start from the date of delivery receipt signed by the user.
The warranty policy

Non-warranty policy
The following circumstances are not within the scope of warranty service, we will provide you with paid after-sales service.
Three guarantees of validity have been issued;Missing or changed invoice;Damage caused by force majeure.
Repair, misuse, collision, negligence, abuse, accident, modification, incorrect use of this product without HIMO's approval, frame serial
number destroyed.
The model of "three guarantees" certificate is inconsistent with or changed from the model of the repaired product;Do not follow the instructions
for proper maintenance.
Due to improper use, direct impact deformation;External force collision or car crash resulting in parts damage;Puncture and air leakage caused
by spikes, glass, sharp small stones, etc.Consumable wear and tear is not replaced in time, causing damage to other parts;The surface of the
cushion is scratched;Violence or man-made damage to the frame, are not covered by the warranty.
The surface of the paint on the frame and parts may be corroded due to rain, collision, friction and other external environmental factors. The
paint may fall off,or the storage place is not good. The surface of the paint may flake after long-term use, and the metal surface or plastic parts
may fade naturally.
Exceeding the scope of use, such as extreme road conditions, performing special effects, climbing stairs, jumping and other abnormal riding
actions, and causing damage to parts or functional failure;
Due to over-limit use caused by deformation or cracking of the frame, also does not belong to the scope of warranty.
Note: HIMO electric vehicle after-sales service policy is final interpreted by Shanghai HIMO electric technology co., LTD.

The HIMO guarantee service standard for electric vehicle parts exceeds the specified service period and scope.
Failure or damage of the HIMO electric vehicle product caused by the user's failure to properly use, drive, maintain and adjust the HIMO
electric vehicle product according to the instructions.
Products sold due to rain, snow immersion, smoke, drugs, chemicals corrosion caused by damage or natural product failure or damage.
Loss is not covered by the warranty.And failure or damage caused by force majeure (including but not limited to earthquake, typhoon, fire,
flood, social event, group event, violent crime, etc.) of the products sold.
The battery was not normally used and maintained by the user, and the battery was placed for a long time (the battery was connected to the
vehicle for a month, and the initial power of the battery was stored separately for less than 50% and more than 3 months), and the battery was
not charged in time, resulting in battery feeding and undervoltage that could not be repaired.
The user refits, disassembles, repairs or destroys the whole product and the normal use of the parts.
The HIMO electric vehicle parts are damaged or the circuit or circuit configuration is changed without permission by the user using
non-original parts.
Product failure or damage caused by human factors such as car crash, car crash, overload and overspeed.
There is no valid three-guarantee voucher, after-sales service card or purchase invoice, voucher or card number inconsistent with the product.
Warranty exemption scope
If the product is sold in the following circumstances, it is not within the scope of warranty service, and users
shall pay for maintenance and related services:

24 month
24 month
12 month
12 month
Tire, Inner tube, Saddle, Chain,
Brake plate, Brake wire,Grip,
Reflector ,Pedal, and accessories.
Battery
Frame Fork
Responsibilities and obligations
Three guarantee policy
Item Allowance for depreciation The warranty period
Hub,Freewheel,Chainwheel,Crank,
BB Set,handlebar,Folding stem,
Seat post, Head set, Wire
Display,Controller , Head light,
Charger
From the date of receipt and signature, the HIMO authorized
after-sales service center will provide after-sales service for
you within the warranty period
Natural open welding, off welding, fracture, deformation, paint off
due to poor manufacturing quality problems
Distortion, breakage, fading, blistering, cracking, paint detachment,
etc due to the poor manufacturing quality problem
Performance failure or quality problem caused by the
product and cannot be repaired
Quick-wear part Consumables are
not guaranteed