HIS KB-M2-WMT Series User manual

Installation Instructions
KB-M2-WMT- _ _ , KB-R2-WMT- _ _ , and KB-R3-WMT- _ _ Series
Wall Mount Folding Keyboard
76.2 mm
(3.00")
450.85 mm
(17.75")
+ 2.3 mm (0.09")
- 0.8 mm (0.03")
38.1 mm
(1.50") Ø
Ø
8 mm (5/16") DIAMETER
OR 1/4-20 TAPPED HOLES
(PREFERRED FOR EASIER
INSTALLATION) (8 PLACES)
PLACE 44" OFF FLOOR
FOR MOST UNIVERSAL
ERGONOMIC HEIGHT
25.4 mm
(1.00")
31.8 mm
(1.25")
11.1 mm
(0.438")
31.8 mm
(1.25")
FIGURE 1 – PANEL MOUNTING PATTERN
1. Cut or drill mounting pattern in panel using the provided cutout template. Refer to Figure 1 for the panel mounting
pattern.
NOTE: +/- 0.8 mm (0.03") tolerance on all dimensions unless otherwise noted
The provided hardware is for use with panels that have a maximum thickness of 6.4 mm (1/4") if using
clearance holes. Thicker panels can be used but require 1/4-20 tapped holes or longer screws than
those provided. For thicker panels or panels where rear access requires a second person, you must
install the plastic bulkhead tting onto the left hand wall bracket rst (as shown in steps 7 and 8), and
then proceed from step 1.
RUBBER WASHER
GASKET
NUT NYLON WASHER
1/4-20 SCREWS
LEFT HAND WALL BRACKET
1/4-20 SCREWS
FIGURE 2 – SIDE VIEW AND FRONT VIEW OF LEFT HAND WALL BRACKET
2. Install the left hand wall bracket rst using four of the provided 1/4-20 screws, washers, and nuts as shown. Tighten
all screws until the gasket is compressed to 1/16" to 3/32" thick.
99109A •December 16, 2019 •www.HopeIndustrial.com •International: [phone] • UK: [phone] •© 2020 Hope Industrial Systems, Inc. •Page 1 of 4

3. Loosely install the right hand wall bracket using only 1 of the provided 1/4-20 screws, washers, and nuts in the location
shown. The remaining three screws will be installed after tting the keyboard in place.
RIGHT HAND WALL BRACKET
1/4-20 SCREW
RUBBER WASHER
NYLON WASHER
1/4-20 SCREW
NUT
FIGURE 3 – FRONT VIEW AND SIDE VIEW OF RIGHT HAND WALL BRACKET
Wall Mount Folding Keyboard Installation Instructions (continued)
CABLE
FIGURE 4 – FRONT VIEW SHOWING KEYBOARD
4. Slide the keyboard cable through the slot on the left hand wall bracket as shown.
IMPORTANT!
THEKEYBOARDMUSTBESUPPORTEDSOTHATNOPRESSUREORWEIGHTISAPPLIEDTOTHECABLE
ITSELF DURING THE INSTALLATION PROCESS.
99109A •December 16, 2019 •www.HopeIndustrial.com •International: [phone] • UK: [phone] •© 2020 Hope Industrial Systems, Inc. •Page 2 of 4

Wall Mount Folding Keyboard Installation Instructions (continued)
RIGHT HAND WALL BRACKET
FIGURE 5 – FRONT AND SIDE VIEWS
5. Swing the right hand wall bracket into place, trapping the keyboard as shown.
GASKET
1/4-20
SCREWS
FIGURE 6 – FRONT VIEW
6. Finish installing the right hand wall bracket using the remaining three 1/4-20 screws, washers, and nuts. Tighten all
screws until the gasket is compressed to 1/16" to 3/32" thick.
7. Unscrew the rst nut from the plastic bulkhead tting on the keyboard cable and remove from the end of the cable.
FIGURE 7 – FRONT VIEW
NUT
PLASTIC BULKHEAD FITTING
99109A •December 16, 2019 •www.HopeIndustrial.com •International: [phone] • UK: [phone] •© 2020 Hope Industrial Systems, Inc. •Page 3 of 4

8. Insert the cable and tting through the hole in the left hand wall bracket. Tightly reinstall the nut from the rear. Push
the cable through as far as it will go, then tighten the cable gland nut from the front.
Wall Mount Folding Keyboard Installation Instructions (continued)
FIGURE 8 – TOP AND FRONT VIEWS
CABLE
NUT PANEL
FIGURE 9 – TOP AND FRONT VIEWS
CABLE
CABLE GLAND
NUT
IMPORTANT!
FAILURETOFULLYTIGHTENEITHERNUTWILLCOMPROMISETHEWATERTIGHTSEALONTHEPANEL.
FIGURE 10 – SIDE VIEW SHOWING 4 POSITIONS
KEYBOARD HAS 4 POSITIONS:
LOCK UP
TYPE UP/FLAT
TYPE DOWN
LOCK DOWN
LIFT TO DISENGAGE FROM LOCK UP POSITION
PULL TO DISENGAGE FROM LOCK DOWN POSITION
99109A •December 16, 2019 •www.HopeIndustrial.com •International: [phone] • UK: [phone] •© 2020 Hope Industrial Systems, Inc. •Page 4 of 4