Hissun WQP4-6204 User manual

( WQP4-6204 )
DISHWASHER USER MANUAL
Every appliance have passed the water test in factory.
It is normal if you found some water leave in appliance.
Please feel free to use it
Please read this instruction carefully before using and keep it safe.

Service Information
Clean dishwasher interior
Error code list
Common fault approach
Circuit diagram
After sales service
Parts of Dishwasher
Technical Information
Package List
Control panel
Overview of programmes
Adding detergent
Utensils selection
B-01
B-02
B-02
D-01
D-02
D-02
D-03
Clean the filter assembly
Clean the spray arms
Tableware placement attention
The use of basket
Installation diagram
Installation steps C-01
C-01
D-03
D-04
E-01
E-01
E-01
F-01
F-01
F-04
F-03
A-01
Important Safety Instructions
CONTENTS
Installation Instructions
Maintenance and Cleaning
Product Overview
Operating Instructions

Important Safety Instructions
!Warning
There are some important safety instructions in this manual, Please read carefully before
installing and using ,
A-01
The dishwasher will be damaged or the user will be injured when the operation is wrong.
This appliance is intended to be used in household and similar applications such as:
– staff kitchen areas in shops, offices and other working environments;
– farm houses;
– by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments..
And the dishwasher can only be used to wash household utensils.
Please contact the after-sales sevice department immediately if the appliance breaks down.
Do not reassembly or fix the appliance by youself.
Please contact the after-sales sevice department or the maintenance department that vendor
assigned for fixing or displacing if the power cord is damaged.
The power source of dishwasher has to adopt earth line for safe. This adoption will protect
the person maximumly, who is shocked by leakage.
Disconnect the power cord atstormy.
After installation, please make sure the connection of water and power well connected
before using.
The installation position of drainage pipe could not exceed 40cm higher than the top of the
appliance, which will cause poor drainage, electrical leakage and water leakage.
Knives and other utensils with sharp points must be loaded in the basket with their points
down or placed in a horizontal position.
This dishwasher is an automatic appliance, do not add water manually when the appliance
is working. It will cause overflow and dangerous.
Do not move or clean appliance when it is working. It might cause electrical or water leakage.
Do not open the door during operation as the steam will hurt you. If it is necessary to load or
unload some utensils, please push pause button and wait 10 seconds, then open the door
slightly and wait for the steam dissipate completely, then open the door and move your
utensils.
Please use specialized detergents. Do not use washing-up liquid, washing powder, hand
sensitizer soup or others detergents that not specialized for dishwasher.
There are some cable ties on the drainage pipe and power cord, please use falt scissor to
cut the ties. Sharp scissor might burst the pipe and cord and cause leakage.
Do not try to use this appliance in damp place. High humidity will make the appliance rust,
even leakage.
The specialized detergent should be put on the place where kids can not reach. because
the detergents are contains acidoid and alkaline, which are really dangerous to kids.
Utensils will be hot after washing, please take it out after 30 minutes.
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●

A-02
●Please keep the appliance at room temperature for 8 hours after receiving the product
in winter, To aviod the droplets appearing on the surface of the glass, and it may
damage the appliance.
The appliance is to be connected to the water mains using new hose sets and that old
hose-sets should not be reused.
During installation, the power supply must not be excessively or dangerously
bent or flattened.
Please use flat scissors to cut the tie of water pipes and power lines when unpacking
boxes.
Position the appliance in the desired location. Confirm that the machine has been leveled.
Please don't put anything else on either side, The openings must not be obstructed by a
carpet.
Please use cold water or warm water not exceeding 50℃.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
The door should not be left in the open position since this could present a tripping
hazard
Please keep kids stay away from the dishwasher, especially when the door open.
After using the appliance, please cut off the power and water
●
●
●
●
●
●
This appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of an electric shock by providing a path of least
resistance of electric current. This appliance is equipped with a cord having an
equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and ordinances.
Improper connection of the equipment-grounding conductor can result in the
risk of an electric shock.
Check with a qualified electrician or service representative if you are in doubt
whether the appliance is properly grounded. Do not modify the plug provided
with the appliance; If it does not fit the outlet. Have a proper outlet installed
by a qualified electrician.
Please do not use power strip.
Grounding instruction
●
●
●
●
●

Product Overview
（Pictures for reference only, The actual product shall govern.）
1
2
Dishwasher interior
2
1
Basket
1
Cutlery basket
2
B-01
Parts of Dishwasher
Lower spray arm
Filter assembled
1
2

*Due to the continuous improvement of products, such as the technical parameters
in this manual are modified without prior notice.
*Please check the accessories one by one after you open the box. Please contact
the seller if there is any shortage or damage.
Package List
*NOTICE:
Please use flat scissors to cut the tie of water pipes and power lines.
Name Quantity
IPX1
785W
AC120V
60Hz
User instruction
Complete appliance
Basket
1
1
1
Cutlery basket
1
Inlet hose
1
1
1
5.8~145PSI
B-02
Technical Information
Outline size
Water pressure
Nominal voltage
Frequency
Waterproof
Rated power
Capacity
W440 X D413 X H424mm
2 Place settings + 6 Serving pieces
Implementation
standards UL749
Name Quantity
Drain hose
Clamping band
Water temperature

2. Please connect the narrower
end of the hose on the tap.
1. Connect inlet pipe
to inlet valve.
Inlet pipe
Installation diagram
This is the default installation mode.
It is recommended that this mode be selected for installation in good
installation conditions. Refer to Steps and for installation.
1 2
Running water inlet
Installation of inlet pipe
1
C-01
NOTICE:When the first time that water in ,the water in appliance turns yellow which is
normal; Because the water softener in water for a long time. Please feel free to use.
Installation Instructions
Installation steps
Inlet valve
Inlet hose
Convenient Connector
Tap

1.Connect the drain and drain
port
2.The drain pipe should
be fixed by the clamping
band
3.Please put the free end
of the drain pipe into the
sink or sewer.
Installation of drain pipe
2
Drain pipe connector
Drain pipe
C-02
Notes：
Wraning!
The inlet pipe can not be recycled. Do not use the old inlet pipe in installation.
!
1. Please use cold water or warm water not exceeding 50℃.
2. The inlet pipe and drain pipe can not be folded, otherwise may affect the washing effect
3. Ensure that the appliance is situated securely on the floor; otherwise it will cause
overflow and electric leakage. Take the package out from appliance.
4. After installation, please retain all documents and components forlater use or for the
subsequent owner
Clamping band
WARNING:
Certain internal parts are intentionally not grounded and may present a
risk of electric shock only during servicing.
Service Personnel. - Do not contact the following parts while the
appliance is energized: Wash pump, Drain pump, Heater.

D-01
1
4
2
3
Button Indicator lamps
Operate the dishwasher
1
Overview of programmes
2
You can delay the start of the programme by up to 24 hours.
Start wash programme by
pressing button.
The indicator lamps flash,
it means the dishwasher
is working.
Change wash programme with
button. Please select a
suitable programme .
Close the door of the
dishwasher and start the
appliance by pressing
for one second,
Press button, the display repeatetedly
shows H:00 H:01...H:24. Select delay start
time. If press for 3 seconds, the screen
will be reset to H:00, which means no
preselection.
Press button to delay the
start of the programme
Select suitable
programme
Start the appliance
Cyclic display
Operating Instructions
Control panel instruction
Po wer P rog ram
St art /Pa use
Delay start
Ch ild l ock
Po wer P rog ram Delay start St art /Pa use
It means button lock. You can secure your appliance from being unintentionally
the programme terminated (e.g. improper operation by children).
Activating the button lock: Hold down the button and for 3 seconds until
“Lock”is indicated on the digital display.
Deactivating the button lock: Hold down the button and for 3 seconds until
the display “Lock” goes out
Button
Delay start Start/Pause
Power Program
Lock
Lock

Special dishwasher detergent will remove oil and food residues. It is a must every
time you use the appliance. Detergent dosage depends on the amount of and type
of soiling.
washing tablet
*Notes：Please don't overuse the detergent. Excessive detergent will not only produce
a lot of bubbles, but also affect the cleaning effect.
Please choose the suitble washing tablet, you should use the small one for
this appliance.
The actual runtime of each program is possibly different from the preset time
cycle due to the water temperature, the amount of utensils, the type of soiling
and the recovery of water softening. It is a normal condition, please use it
with confidence.
D-02
Very adhesive burned-in or
dried-on food remnants 2:00
Intensive
Part dried, common household
food remnants 9g 2:25
Eco
Fresh food remnants, Light
and less oil.
Glass
1:00
Normal
Slightly adhesive, temperature-
sensitive plastic and glasses 9g 1:30
Rapid
washing powder
Type of soiling
Programme Time cycle
1pcs
1pcs
washing tablet
Consumption of detergent
9g 1pcs
-
9g 1pcs
0:35
washing powder
Little dried, nomal household
food remnants
Overview of programmes
-
Adding detergent
Add the required amount of detergent after pushed basket.
Please put the detergent in the designated place.

Ceramic tableware
Dishwasher-proof utensils:
Utensils notes：
D-03
Utensils selection
Glassware Stainless steel tableware
1. Precious metal, aluminium and colored glaze utensils may turn cloudy after being
washed in a dishwasher.
2. Cutlery made of bamboo or wood: It may come loose orcrack at high temperatures.
3. Plastics items: Please see manufacturer’s instructions for plastics cutlery or items
with plastics parts, because these items may come loose or crack at high temperature.
4. Cleaning cloth: Cleaning cloth may cause dishwasher fault.
5. Cast iron items: Cast iron items may rust after being washed in a dishwasher.
Tableware placement attention
1. Remove large food remnants such as bones or leaves;
2. All utensils with dirt should be face down. If their opening face or closing face down
will leave the water on the top.
3. Utensils are secure and cannot tip over, one place for one utensil.
4. Do not let the utensils out of basket to obstruct rotation of spray arms.
5. The small size of utensils might drop out from the basket and obstruct the spray
arms rotation, Please do not put these small items in the appliance.
6. When pushing basket back, do not let the sharp parts of utensils cut the seal.
7. The top coat of basket can not be scratched, or it will be rusted.
8. Place cutlery, always unsorted with the tips face down, in the cutlery basket.
TIPS:
Flip the spray arm after pushed basket, to check if the spray arm still can be rotates.

D-04
Loading the basket

After appliance ran a while, there will be some residue and other things left in it.
Please clean it when you see the residue and things, also clean the appliance immediately.
Make sure the power
is off. Turn the filter assembly
out with anticlockwise.
And put the filter assembly
back with clockwise.
A
Pull the main basket
out of appliance, and
lift the lower spray
arm a little bit for loss
the clips.
Check if the spray arms
blocked. If it does, please
use a thin wire to pull
the blockages out or
flush the hole with water.
C-03
Use flowing water to flush filter
assembly.Do not use steel wool
or iron brush, it will cause the
filter rust.
B
A
E-01
Maintenance and Cleaning
Clean the filter assembly
Clean the spray arms
Clean dishwasher interior
Leaky seal and the seal of door should use the wet damp cloth to clean.
Clean the dead corner, Inside the dishwasher with citric acid and wet cloth.
Please use specialized detergent to clean liner of dishwasher and inner
pipeline with instruction.
B

E01
Error code
E02
E03
E04
Cause Remedy
E05
1.ean the appliance about 30°to 45°to pour out the water in L
the bottom plate,
2.Check if the drainage pipe is placed too high,
3.Check if the pipe be tired a knot, blocked or pressed,
4.Check if the appliance be placed right
5.Exclude above cause, try to restart the appliance again.
Please contact the after-sales service department.
E06
Error code list
The washing powder
and washing tablet
have not been
cleaned up
1.The holes of spray arm been blocked,
the washing powder can not be fiushed
out.
Run the quick wash mode again and put
moderate washing powder as instruction next
time.
Clean the holes of spary arms and run the
quick wash mode again to clean the utensil.
2.Put too much washing power.
Use specialized washing powder and washing
tablet with quick wash mode to wash the
utensil again
Some foam in the
liner
If there's not much foam,you can open the door
and let the foam come less and less; If there's
too much foam,you can remove it with tools. At
last,restart any programme about 3 minutes.
Redo this again and again until the foam is
disappear
Didn't use speciallized washing powder
or put too much washing powder in it
3.Used low-quality washing power
It's normal and it won't impact the
utensil
Some drops in the
inner of liner
Problem Cause Remedy
Utensils is wet 2.The washing process is still running
3.Programme selected without drying
Refer to utensils place rule
Wait until process finished
Select programme with drying (See overview
of programmes.)
1.Utensils be piled up and without lean
E10 Water inflow abnormal
1.The tap was not fully opened.
2.Small inflow and low water pressure.
3.Start-up multiple times in case of water shortage.
4.Please contact the after-sales service department.
4.Improper placement of detegent Reference“Adding detergent”
F-01
Service Information
Thermistor short circuit
Thermistor open circuit
Please contact the after-sales service department
The machine is not
heated
1. Please make sure the utensils be placed correctly. Water will
be lack if it is in the plate/bow.
2. Please contact the after-sales service department
Inlet valve failure
Overflow
Heating function
abnormal
Please contact the after-sales service department
Please contact the after-sales service department
Please contact the after-sales service department
Common fault approach

If the solutions above can not fix the problems, please stop to use appliance immediately
and cut off the power and water supply. Please contact the after-sales department.
Problem Cause Remedy
1.Have not closed the door。close the door.
2.There are greasy dirt or water on the
glass and hand.
Have no reflection when
pressing any button
except the power botton.
Make sure the water supply have no
problem
The water light in control
panel is lighting when
water comes in.
Please add water to the container and
make sure the suction pipe is in the water
It's normal and be free to use
The water intake time is
longer when water comes
in from the suction pump
2.The flowmeter is broken
3.The filling valve is broken
1.Check if the water supply have problem
1.There is no water in the container or the
suction pipe is not in the water.
No reflection after turn
on the power
1.If all the lights were off and no reflection
when you press the button, there are
possibilities that you didn't plug in the
power or the power was blackout.
Please plug the power in and make sure
the power have no issue.
3.All the light are on, it might on the
childproof locking mode。Unlock the childproof lock
4.PCB lock of door is broken Please contact the after sales service
department。
The water light in control
panel is lighting when
water comes in from the
Suction pump.
2.power or the power was blackout Clean plug the power in and make sure
they are dry.
3.All the light are on, it might on the
childproof locking mode。
4.The time that touch power icon is too
short. Press the power icon for 1 second
The utensil was not
cleaned up
1.utensils be piled up and without lean
3.Do not use pecialized washing powder
or put too little of washing power.
Refer to utensils place rule
Use specialized washing powder and put
enough of it before washing
Re-install the filter in right position
4.Do not install the filter in right position
and the food remnants get in it
Clean the inner part of spray arms
Please choose the right programme of
washing
5.The spray arms were blocked
Check if the spray arm is stuck by the
utensil
6.The spray arms are stuck
Soak the utensil for a while before
washing
7.Some food remnants are sticking on the
utensil
Restart the washing programme8.Black out when the appliance is working
Have crashing noise when
it is working
Unload the dishwasher and replace the
utensils in proper way
Place the utensil in improper way ,some
utensils is obstructing the spray arms; or
some utensils are crashing each other.
Suggest wash utensil with steel wool
before put it in appliance to wash
9.Some food remnants are too hard to
wash
1.The position of drainage pipe is too high
2.The drainage pipe is tied,blocked or
pressed by something heavy
Refer to drainage pipe installation
Untie the pipe and remove the heavy
thing
3.Drainage pump is broken
4.The filling valve is broken
A lot of water were left
in appliance when is not
working
2.Dirty clogging of suction pipe filter Clean the filter screen of the suction pipe
F-02
Clean plug the power in and make sure
they are dry.
Unlock the childproof lock
Please contact the after sales service
department。
Please contact the after sales service
department。
3.The filling valve is broken Please contact the after sales service
department。
2.Do not chose the right programme of
washing
Please contact the after sales service
department。
Please contact the after sales service
department。

F-03
Circuit diagram
CN19
T
FUSE
EGND
EGND
ACN
ACN
ACN
ACL
ACL
White
Heat Heat
EV-Z1
EV-Z
Inlet valve
Washer pump
Draining pump
ML
PSB
control
GND
K-YL
FM
DOOR
RE
Floodcock
Flowmeter
Door
Thermistor
t

*Provide valid vouchers for purchasing products during the warranty period：
Invoice or product SN code.
*Free warranty within 12 months based on the date of SN code of the product
leaving the factory.
*The following conditions do not fall within the scope of free maintenance during
the warranty period, ：
1、Damage caused by improper use and maintenance of users；
2、Failure to produce valid vouchers (neither invoices nor product SN codes),
unclear valid vouchers, unable to confirm or altered；
3、Damage caused by irresistible natural disasters (typhoons, snow disasters,
hail, earthquakes, debris flows, etc.。)
4、Repair by an unqualified third party.
Warranty requirements
After sales service
1
Maintenance record card
2
F-04
Maintenance
frequency
Fault
phenomenon
Maintenance
record
Maintenance
date
Signature of
maintenance
personnel
1
2
3
5
4
Note: After maintenance, the maintenance staff need to make a record of
the maintenance status, for offer you a better service in the future.

STATEMENT :
With the innovation and improvement of product technology, the product
specifications of the same model as this product may be changed, and
the change part will be notified without further notice.
The pictures of the products in the instruction are all borrowed from the
appearance of the dishwasher, and the pictures are only used as an
example. The actual appearance should be based on the purchased
products.
As a result of product improvement, the execution standards of product
manufacturing may be changed, and the revised standards of execution
will be changed.
There is no retroactive effect on the sold product.