Hitachi 22LD4500UK User manual

CAUTION:
Before servicing this chassis, it is important that the service technician read the “Safety
Precautions” and “Product Safety Notices” in this service manual.
ATTENTION:
Avant d’effectuer l’entretien du châassis, le technicien doit lire les «Précautions de sécurité»
et les «Notices de sécurité du produit» présentés dans le présent manuel.
VORSICHT:
Vor Öffnen des Gehäuses hat der Service-Ingenieur die „Sicherheitshinweise“ und „Hinweise
zur Produktsicherheit“ in diesem Wartungshandbuch zu lesen.
SERVICE MANUAL
MANUEL D'ENTRETIEN
WARTUNGSHANDBUCH
Data contained within this Service
manual is subject to alteration for
improvement.
Les données fournies dans le présent
manuel d’entretien peuvent faire l’objet
de modifications en vue de perfectionner
le produit.
Die in diesem Wartungshandbuch
enthaltenen Spezifikationen können sich
zwecks Verbesserungen ändern.
SPECIFICATIONSAND PARTS ARE SUBJECTTO CHANGE FOR IMPROVEMENT
Colour Television
September 2004
No. 0205
22LD4500UK

i
TABLE OF CONTENTS
1. INTRODUCTION........................................................................................................................... 1
2. TUNER............................................................................................................................................. 1
3. IF PART (TDA988X)..................................................................................................................... 1
4. MULTI STANDARD SOUND PROCESSOR.......................................................................... 1
5. AUDIO AMPLIFIER STAGE WITH AN7522........................................................................... 2
6. POWER........................................................................................................................................... 2
7. MICROCONTROLLER SDA55XX............................................................................................. 2
7.1. General Features ............................................................................................................................ 2
7.2. External Crystal and Programmable Clock Speed............................................................................ 2
7.3. Microcontroller Features.................................................................................................................. 2
7.4. Memory........................................................................................................................................... 2
7.5. Display Features............................................................................................................................. 2
7.6. ROM Characters............................................................................................................................. 3
7.7. Acquisition Features........................................................................................................................ 3
7.8. Ports............................................................................................................................................... 3
8. SERIAL ACCESS CMOS 16K (2048*8) EEPROM ST24C16............................................ 3
9. CLASS AB STEREO HEADPHONE DRIVER TDA1308..................................................... 3
10. SAW FILTERS............................................................................................................................... 3
11. IC DESCRIPTIONS...................................................................................................................... 4
11.1. LM1117 ....................................................................................................................................... 4
11.1.1. General Description............................................................................................................ 4
11.1.2. Features .............................................................................................................................. 4
11.1.3. Applications........................................................................................................................ 4
11.1.4. Connection Diagrams......................................................................................................... 4
11.2. LM2576 ....................................................................................................................................... 5
11.2.1. General Description............................................................................................................ 5
11.2.2. Features .............................................................................................................................. 5
11.2.3. Pin description.................................................................................................................... 5
11.3. LM317T ....................................................................................................................................... 6
11.3.1. Description.......................................................................................................................... 6
11.3.2. Features .............................................................................................................................. 6
11.4. TFMS5360................................................................................................................................... 6
11.4.1. Description.......................................................................................................................... 6
11.4.2. Features .............................................................................................................................. 6
11.5. ST24LC21 ................................................................................................................................... 7
11.5.1. Description.......................................................................................................................... 7
11.5.2. Features .............................................................................................................................. 7
11.5.3. Pin connections.................................................................................................................. 7
11.6. SST37VF040............................................................................................................................... 8
11.6.1. Description.......................................................................................................................... 8
11.6.2. Features .............................................................................................................................. 8
11.6.3. Pin Description ................................................................................................................... 8
11.7. TEA5114A................................................................................................................................... 9
11.7.1. General description ............................................................................................................ 9
11.7.2. Features .............................................................................................................................. 9
11.7.3. Pin Connections.................................................................................................................. 9
11.8. TEA6415 ................................................................................................................................... 10
11.8.1. General description .......................................................................................................... 10
11.8.2. 13.5.2.Features.................................................................................................................. 10
11.8.3. 13.5.3.Pinning.................................................................................................................... 10
11.9. VPC3230D................................................................................................................................. 11
11.9.1. General Description.......................................................................................................... 11
11.9.2. Pin Connections and Short Descriptions ........................................................................ 11
11.10. SDA55XX (SDA5550)................................................................................................................ 13
11.10.1. General description .......................................................................................................... 13

ii
11.11. TDA9885/86 .............................................................................................................................. 14
11.11.1. General description .......................................................................................................... 14
11.11.2. Features ............................................................................................................................ 14
11.11.3. Pinning.............................................................................................................................. 14
11.12. TDA1308 ................................................................................................................................... 15
11.12.1. General Description.......................................................................................................... 15
11.12.2. Features ............................................................................................................................ 15
11.12.3. Pinning.............................................................................................................................. 15
11.13. AN7522N................................................................................................................................... 15
11.13.1. General description .......................................................................................................... 15
11.13.2. Pin Descriptions................................................................................................................ 15
11.14. PI5V330..................................................................................................................................... 16
11.14.1. General description .......................................................................................................... 16
11.14.2. Features ............................................................................................................................ 16
11.14.3. Pin Descriptions................................................................................................................ 16
11.15. GM6015..................................................................................................................................... 17
11.15.1. General description .......................................................................................................... 17
11.15.2. Features ............................................................................................................................ 17
11.16. SAA3010T................................................................................................................................. 18
11.16.1. Description........................................................................................................................ 18
11.16.2. Features ............................................................................................................................ 18
11.16.3. Pinning.............................................................................................................................. 18
11.17. AD9883A................................................................................................................................... 19
11.17.1. General description .......................................................................................................... 19
11.17.2. Features ............................................................................................................................ 19
11.17.3. Pin Descriptions................................................................................................................ 19
11.18. MC141585................................................................................................................................. 22
11.18.1. General description .......................................................................................................... 22
11.18.2. Features ............................................................................................................................ 22
11.18.3. Pin Description ................................................................................................................. 22
11.19. MC34063................................................................................................................................... 24
11.19.1. Description........................................................................................................................ 24
11.19.2. Features ............................................................................................................................ 24
11.19.3. Pin connections................................................................................................................ 24
11.20. MSP34X0G................................................................................................................................ 25
11.20.1. Introduction....................................................................................................................... 25
11.20.2. Features ............................................................................................................................ 25
11.20.3. Pin connections................................................................................................................ 26
11.21. DS90C385................................................................................................................................. 27
11.21.1. General Description.......................................................................................................... 27
11.21.2. Features ............................................................................................................................ 27
11.21.3. Pin Descriptions................................................................................................................ 28
11.22. LM1084 ..................................................................................................................................... 30
11.22.1. General description .......................................................................................................... 30
11.22.2. Features ............................................................................................................................ 30
11.22.3. Connection Diagrams....................................................................................................... 30
12. SERVICE MENU SETTINGS................................................................................................... 31
12.1. ADJUST MENU SETTINGS....................................................................................................... 31
12.2. OPTIONS MENU SETTINGS..................................................................................................... 32
12.3. APS WSS TEST MENU............................................................................................................. 36
13. BLOCK DIAGRAM...................................................................................................................... 37
14. CIRCUIT DIAGRAMS................................................................................................................. 41

1
1. INTRODUCTION
22” TFT-LCD TV is a Progressive TV control system based on the µ-controller SDA555X, with built-in de-
interlacer and scaler.
TFT TV is a progressive scan flicker free colour television with PC input, driving an WXGA (1280*720)
panel with 16:9 aspect ratio. The chassis is capable of operation in PAL, SECAM, NTSC (playback) colour
standards and multiple transmission standards as B/G, D/K, I/I’, and L/L´. Sound system output is
supplying 2x3W (10%THD) for left and right outputs of 16O speakers. The chassis is equipped with two full
SCART’s, one front-AV, one SVHS, one D-Sub 15 (PC) input, one PC stereo audio input and one line out
(left and right) and one HP outputs.
2. TUNER
As the thickness of the TV set has a limit, a horizontal mounted tuner is used in the product, which is
suitable for CCIR systems B/G, H, L, L´, I/I´, and D/K. The tuning is available through the digitally
controlled I2C bus (PLL). Below you will find info on the Tuner in use.
General description of UV1316:
The UV1316 tuner belongs to the UV 1300 family of tuners, which are designed to meet a wide range of
applications. It is a combined VHF, UHF tuner suitable for CCIR systems B/G, H, L, L’, I and I’. The low IF
output impedance has been designed for direct drive of a wide variety of SAW filters with sufficient
suppression of triple transient.
Features of UV1316:
1. Member of the UV1300 family small sized UHF/VHF tuners
2. Systems CCIR: B/G, H, L, L’, I and I’; OIRT: D/K
3. Digitally controlled (PLL) tuning via I2C-bus
4. Off-air channels, S-cable channels and Hyper band
5. Compact size
6. Complies to “CENELEC EN55020” and “EN55013”
Pinning:
1. Gain control voltage (AGC) :4.0V, Max: 4.5V
2. Tuning voltage
3. I²C-bus address select :Max: 5.5V
4. I²C-bus serial clock :Min:-0.3V, Max: 5.5V
5. I²C-bus serial data :Min:-0.3V, Max: 5.5V
6. Not connected
7. PLL supply voltage :5.0V, Min: 4.75V, Max: 5.5V
8. ADC input
9. Tuner supply voltage :33V, Min: 30V, Max: 35V
10. Symmetrical IF output 1
11. Symmetrical IF output 2
3. IF PART (TDA988X)
The TDA9885 is an alignment-free single standard (without positive modulation) vision and sound IF signal
PLL.
The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) vision and sound IF signal
PLL demodulator for positive and negative modulation including sound AM and FM processing.
Both devices can be used for TV, VTR, PC and set-top box applications.
4. MULTI STANDARD SOUND PROCESSOR
The MSP34x0G family of single-chip Multistandard Sound Processors covers the sound processing of all
analog TV-Standards worldwide, as well as the NICAM digital sound standards. The full TV sound
processing, starting with analog sound IF signal-in, down to processed analog AF-out, is performed on a
single chip.
These TV sound processing ICs include versions for processing the multichannel television sound (MTS)
signal conforming to the standard recommended by the Broadcast Television Systems Committee (BTSC).
The DBX noise reduction, or alternatively, Micronas Noise Reduction (MNR) is performed alignment free.
Other processed standards are the Japanese FM-FM multiplex standard (EIA-J) and the FM Stereo Radio
standard.
Current ICs have to perform adjustment procedures in order to achieve good stereo separation for BTSC
and EIA-J. The MSP 34x1G has optimum stereo performance without any adjustments.

2
5. AUDIO AMPLIFIER STAGE WITH AN7522
The AN7522 is an audio class-AB amplifier assembled in SIL-12 Pin Plastic Package specially designed
for sound cards application. Using this IC chassis operates as a stereo TV set. AN7522 has stand-by
feature for low stand-by power consumption and mute feature for pop noise free opening and closing the
TV set. It can deliver 2*3W without clipping at 12V/16O applications.
6. POWER
The LM2576 series of regulators are monolithic integrated circuits ideally suited for easy and convenient
design of a step–down switching regulator (buck converter). All circuits of this series are capable of driving
a 3.0A load with excellent line and load regulation. Two different versions (one having a fixed output
voltage of 3.3 V, and one with 5.0 V) of this IC are used in the regulator board.
7. MICROCONTROLLER SDA55XX
7.1. General Features
• Feature selection via special function register
• Simultaneous reception of TTX, VPS, PDC, and WSS (line 23)
• Supply Voltage 2.5 and 3.3 V
• ROM version is used.
7.2. External Crystal and Programmable Clock Speed
• Single external 6MHz crystal, all necessary clocks are generated internally
• CPU clock speed selectable via special function registers.
• Normal Mode 33.33 MHz CPU clock, Power Save mode 8.33 MHz
7.3. Microcontroller Features
• 8bit 8051 instruction set compatible CPU.
• 33.33-MHz internal clock (max.)
• 0.360 µs (min.) instruction cycle
• Two 16-bit timers
• Watchdog timer
• Capture compare timer for infrared remote control decoding
• Pulse width modulation unit (2 channels 14 bit, 6 channels 8 bit)
• ADC (4 channels, 8 bit)
• UART (rxd, txd)
7.4. Memory
• Up to 128 Kilobyte on Chip Program ROM
• Eight 16-bit data pointer registers (DPTR)
• 256-bytes on-chip Processor Internal RAM (IRAM)
• 128bytes extended stack memory.
• Display RAM and TXT/VPS/PDC/WSS-Acquisition-Buffer directly accessible via MOVX
• UP to 16KByte on Chip Extended RAM (XRAM) consisting of;
-1 Kilobyte on-chip ACQ-buffer-RAM (access via MOVX)
-1 Kilobyte on-chip extended-RAM (XRAM, access via MOVX) for user software
-3-Kilobyte Display Memory
7.5. Display Features
• ROM Character set supports all East and West European Languages in single device
• Mosaic Graphic Character Set
• Parallel Display Attributes
• Single/Double Width/Height of Characters
• Variable Flash Rate
• Programmable Screen Size (25 Rows x 33...64 Columns)
• Flexible Character Matrixes (HxV) 12 x 9...16
• Up to 256 Dynamical Redefinable Characters in standard mode; 1024 Dynamical Redefinable Characters
in Enhanced Mode
• CLUT with up to 4096 colour combinations
• Up to 16 Colours per DRCS Character
• One out of 8 Colours for Foreground and Background Colours for 1-bit DRCS and ROM Characters

3
7.6. ROM Characters
• Shadowing
• Contrast Reduction
• Pixel by Pixel Shiftable Cursor With up to 4 Different Colours
• Support of Progressive Scan and 100 Hz.
• 3 X 4Bits RGB-DACs On-Chip
• Free Programmable Pixel Clock from 10 MHz to 32MHz
• Pixel Clock Independent from CPU Clock
• Multinorm H/V-Display Synchronisation in Master or Slave Mode
7.7. Acquisition Features
• Multistandard Digital Data Slicer
• Parallel Multi-norm Slicing (TTX, VPS, WSS, CC, G+)
• Four Different Framing Codes Available
• Data Caption only limited by available Memory
• Programmable VBI-buffer
• Full Channel Data Slicing Supported
• Fully Digital Signal Processing
• Noise Measurement and Controlled Noise Compensation
• Attenuation Measurement and Compensation
• Group Delay Measurement and Compensation
• Exact Decoding of Echo Disturbed Signals
7.8. Ports
• One 8-bit I/O-port with open drain output and optional I 2 C Bus emulation support (Port0)
• Two 8-bit multifunction I/O-ports (Port1, Port3)
• One 4-bit port working as digital or analogue inputs for the ADC (Port2)
• One 2-bit I/O port with secondary function (P4.2, 4.3, 4.7)
• One 4-bit I/O-port with secondary function (P4.0, 4.1, 4.4) (Not available in P-SDIP 52)
8. SERIAL ACCESS CMOS 16K (2048*8) EEPROM ST24C16
The ST24C16 is a 16Kbit electrically erasable programmable memory (EEPROM), organised as 8 blocks
of 256*8 bits. The memory is compatible with the I²C standard, two wire serial interface, which uses a bi-
directional data bus and serial clock. The memory carries a built-in 4 bit, unique device identification code
(1010) corresponding to the I²C bus definition. This is used together with 1 chip enable input (E) so that up
to 2*8K devices may be attached to the I²C bus and selected individually.
9. CLASS AB STEREO HEADPHONE DRIVER TDA1308
The TDA1308 is an integrated class AB stereo headphone driver contained in a DIP8 plastic package. The
device is fabricated in a 1 mm CMOS process and has been primarily developed for portable digital audio
applications.
10.SAW FILTERS
K3953M is an IF Filter for Video Applications. The package is SIP5K. Supported standards are B/G, D/K, I,
L/L’.
K9656M is an IF Filter for Audio Applications. The package is SIP5K. Supported standards are B/G, D/K, I,
L/L’.

4
11.IC DESCRIPTIONS
LM1117 TDA1308T
LM2576 AN7522N
LM317T PI5V330
TFMS5360 GM6015
ST24LC21 SAA3010T
SST37VF040 AD9883A
TEA5114A MC141585
TEA6415 MC34063
VPC3230D MSP3410G
SDA55XX DS90C385
TDA9885/86 LM1084
11.1. LM1117
11.1.1. General Description
The LM1117 is a series of low dropout voltage regulators with a dropout of 1.2V at 800mA of load current.
It has the same pin-out as National Semiconductor’s industry standard LM317. The LM1117 is available in
an adjustable version, which can set the output voltage from 1.25V to 13.8V with only two external
resistors. In addition, it is also available in five fixed voltages, 1.8V, 2.5V, 2.85V, 3.3V, and 5V.
The LM1117 offers current limiting and thermal shutdown. Its circuit includes a zener trimmed bandgap
reference to as-sure output voltage accuracy to within ±1%. The LM1117 series is available in SOT-223,
TO-220, and TO-252 D-PAK packages. A minimum of 10µF tantalum capacitor is required at the output to
improve the transient response and stability.
11.1.2. Features
• Available in 1.8V, 2.5V, 2.85V, 3.3V, 5V, and Adjustable Versions
• Space Saving SOT-223 Package
• Current Limiting and Thermal Protection
• Output Current 800mA
• Line Regulation 0.2% (Max)
• Load Regulation 0.4% (Max)
•Temperature Range
LM1117 0°C to 125°C
LM1117I -40°C to 125°C
11.1.3. Applications
• 2.85V Model for SCSI-2 Active Termination
• Post Regulator for Switching DC/DC Converter
• High Efficiency Linear Regulators
• Battery Charger
• Battery Powered Instrumentation
11.1.4. Connection Diagrams

5
11.2. LM2576
11.2.1. General Description
The LM2576 series of regulators are monolithic integrated circuits ideally suited for easy and convenient
design of a step–down switching regulator (buck converter). All circuits of this series are capable of driving
a 3.0 A load with excellent line and load regulation.
These devices are available in fixed output voltages of 3.3 V, 5.0 V, 12 V, 15 V, and an adjustable output
version. These regulators were designed to minimize the number of external components to simplify the
power supply design. Standard series of inductors optimized for use with the LM2576 are offered by
several different inductor manufacturers.
Since the LM2576 converter is a switch–mode power supply, its efficiency is significantly higher in
comparison with popular three–terminal linear regulators, especially with higher input voltages. In many
cases, the power dissipated is so low that no heatsink is required or its size could be reduced dramatically.
A standard series of inductors optimized for use with the LM2576 are available from several different
manufacturers. This feature greatly simplifies the design of switch–mode power supplies.
The LM2576 features include a guaranteed ±4% tolerance on output voltage within specified input voltages
and output load conditions, and ±10% on the oscillator frequency (±2% over 0°C to 125°C). External
shutdown is included, featuring 80 mA (typical) standby current. The output switch includes cycle–by–cycle
current limiting, as well as
thermal shutdown for full protection under fault conditions.
11.2.2. Features
• 3.3 V, 5.0 V, 12 V, 15 V, and Adjustable Output Versions
• Adjustable Version Output Voltage Range, 1.23 to 37 V ±4% Maximum Over Line and Load Conditions
• Guaranteed 3.0 A Output Current
• Wide Input Voltage Range
• Requires Only 4 External Components
• 52 kHz Fixed Frequency Internal Oscillator
• TTL Shutdown Capability, Low Power Standby Mode
• High Efficiency
• Uses Readily Available Standard Inductors
• Thermal Shutdown and Current Limit Protection
• Moisture Sensitivity Level (MSL) Equals 1
11.2.3. Pin description

6
11.3. LM317T
11.3.1. Description
The LM317T is an adjustable 3 terminal positive voltage regulator capable of supplying in excess of 1.5
amps over an output range of 1.25 to 37 volts. This voltage regulator is exceptionally easy to use and
requires only two external resistors to set the output voltage. Further, it employs internal current limiting,
thermal shutdown and safe area compensation, making it essentially blow–out proof. The LM317 serves a
wide variety of applications including local, on card regulation. This device can also be used to make a
programmable output regulator, or by connecting a fixed resistor between the adjustment and output, the
LM317 can be used as a precision current regulator.
11.3.2. Features
• Output Current in Excess of 1.5 A
• Output Adjustable between 1.2 V and 37 V
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting Constant with Temperature
• Output Transistor Safe–Area Compensation
• Floating Operation for High Voltage Applications
• Available in Surface Mount D2PAK, and Standard 3–Lead Transistor Package
• Eliminates Stocking many Fixed Voltages
11.4. TFMS5360
11.4.1. Description
The TFMS5360 is a miniature receiver for infrared remote control systems.
11.4.2. Features
• Photo detector and preamplifier in one.
• 36 KHZ
• Pin diode and preamp
• IR filter.

7
11.5. ST24LC21
11.5.1. Description
The ST24LC21 is a 1K bit electrically erasable programmable memory (EEPROM), organized by 8 bits.
This device can operate in two modes: Transmit Only mode and I2C bidirectional mode. When powered,
the device is in Transmit Only mode with EEPROM data clocked out from the rising edge of the signal
applied on VCLK. The device will switch to the I2C bidirectional mode upon the falling edge of the signal
applied on SCL pin. The ST24LC21 can not switch from the I2C bidirectional mode to the Transmit Only
mode (except when the power supply is removed). The device operates with a power supply value as low
as 2.5V. Both Plastic Dual-in-Line and Plastic Small Outline packages are available.
11.5.2. Features
• 1 million Erase/Write cycles
• 40 years data retention
• 2.5V to 5.5V single supply voltage
• 400k Hz compatibility over the full range of supply voltage
• Two wire serial interface I2C bus compatible
• Page Write (Up To 8 Bytes)
• Byte, random and sequential read modes
• Self timed programming cycle
• Automatic address incrementing
• Enhanced ESD/Latch up
• Performances
11.5.3. Pin connections
DIP Pin connections CO Pin connections
NC: Not connected
Signal names
SDA Serial data Address Input/Output
SCL Serial Clock (I2C mode)
Vcc Supply voltage
Vss Ground
VCLK Clock transmit only mode

8
11.6. SST37VF040
11.6.1. Description
The SST37VF512/010/020/040 devices are 64K x8 / 128Kx8 / 256K x8 / 512K x8 CMOS, Many-Time
Programmable (MTP), low cost flash, manufactured with SST’s proprietary, high performance CMOS
Super Flash technology. The split-gate cell design and thick oxide tunneling injector attain better reliability
and manufacturability compared with alternate approaches. The SST37VF512/010/020/040 can be
electrically erased and programmed at least 1000 times using an external programmer, e.g., to change the
contents of devices in inventory. The SST37VF512/010/020/040 have to be erased prior to programming.
These devices conform to JEDEC standard pinouts for byte-wide flash memories. Featuring high
performance Byte-Program, the SST37VF512/010/020/040 provide a typical Byte-Pro-gram time of 10 µs.
Designed, manufactured, and tested for a wide spectrum of applications, these devices are offered with an
endurance of at least 1000 cycles. Data retention is rated at greater than 100 years. The
SST37VF512/010/020/040 are suited for applications that require infrequent writes and low power
nonvolatile storage. These devices will improve flexibility, efficiency and performance while matching the
low cost in nonvolatile applications that currently use UV-EPROMs, OTPs, and mask ROMs.
11.6.2. Features
• Organized as 64K x8 / 128K x8 / 256K x8 / 512K x8
• 2.7-3.6V Read Operation
• Superior Reliability
–Endurance: At least 1000 Cycles
–Greater than 100 years Data Retention
• Low Power Consumption:
–Active Current: 10 mA (typical)
–Standby Current: 2 µA (typical)
• Fast Read Access Time:
–70 ns
–90 ns
• Latched Address and Data
• Fast Byte-Program Operation:
–Byte-Program Time: 10 µs (typical)
–Chip Program Time:
0.6 seconds (typical) for SST37VF512
1.2 seconds (typical) for SST37VF010
2.4 seconds (typical) for SST37VF020
4.8 seconds (typical) for SST37VF040
• Electrical Erase Using Programmer
–Does not require UV source
–Chip-Erase Time: 100 ms (typical)
• CMOS I/O Compatibility
• JEDEC Standard Byte-wide Flash EEPROM Pinouts
• Packages Available
–32-lead PLCC
–32-lead TSOP (8mm x 14mm)
–32-pin PDIP
11.6.3. Pin Description
Symbol Pin nameFunctions
AMS1-A0Address Inputs To provide memory addresses.
DQ7-DQ0 Data Input/output To output data during Read cycles and receive input data during Program cycles.
The outputs are in tri-state when OE# or CE# is high.
CE# Chip Enable To activate the device when CE# is low.
WE# Write Enable To program or erase (WE# = VIL pulse during Program or Erase)
OE# Output Enable To gate the data output buffers during Read operation when low
VDD Power Supply To provide 3.0V supply (2.7-3.6V)
VSS Ground
NC No Connection Unconnected pins.
1. AMS = Most significant address
AMS = A15 for SST37VF512, A16 for SST37VF010, A17 for SST37VF020, and A18 for SST37VF040

9
11.7. TEA5114A
11.7.1. General description
This integrated circuit provides RGB switching allowing connections between peri TV plug, internal RGB
generator and video processor in a TV set.
The input signal black level is tied to the same reference voltage on each input in order to have no
differential voltage when switching two RGB generators.
An AC output signal higher than 2 Vpp makes gain going slowly down to 0dBto protect the TV set video
amplifier from saturation.
Fast blanking output is a logical OR between FB1 (Pin 8) and FB2 (Pin 10).
11.7.2. Features
• 25MHz Bandwidth
• Crosstalk : 55dB
• Short circuit to ground or VCC protected
• Anti saturation gain changing
• Video switching
11.7.3. Pin Connections

10
11.8. TEA6415
11.8.1. General description
The main function of the IC is to switch 8 video input sources on 6 outputs. Each output can be switched
on only one of each input. On each input an alignment of the lowest level of the signal is made (bottom of
synch. top for CVBS or black level for RGB signals). Each nominal gain between any input and output is
6.5dB. For D2MAC or Chroma signal the alignment is switched off by forcing, with an external resistor
bridge, 5 VDC on the input. Each input can be used as a normal input or as a MAC or Chroma input (with
external resistor bridge). All the switching possibilities are changed through the BUS. Driving 75? load
needs an external transistor. It is possible to have the same input connected to several outputs. The
starting configuration upon power on (power supply: 0 to 10V) is undetermined. In this case, 6 words of 16
bits are necessary to determine one configuration. In other case, 1 word of 16 bits is necessary to
determine one configuration.
11.8.2. 13.5.2.Features
• 20MHz Bandwidth
• Cascadable with another TEA6415C (Internal address can be changed by pin 7 voltage)
•8 Inputs (CVBS, RGB, MAC, CHROMA,...)
• 6 Outputs
• Possibility of MAC or chroma signal for each input by switching-off the clamp with an external resistor
bridge
• Bus controlled
• 6.5dB gain between any input and output
• 55dB crosstalk at 5mHz
• Fully ESD protected
11.8.3. 13.5.3.Pinning
1. Input :Max : 2Vpp, Input Current: 1mA, Max: 3mA
2. Data :Low level : -0.3V Max: 1.5V,
High level : 3.0V Max : Vcc+0.5V
3. Input :Max : 2Vpp, Input Current: 1mA, Max : 3mA
4. Clock :Low level : -0.3V Max: 1.5V,
High level : 3.0V Max : Vcc+0.5V
5. Input :Max : 2Vpp, Input Current: 1mA, Max: 3mA
6. Input :Max : 2Vpp, Input Current: 1mA, Max: 3mA
7. Prog
8. Input :Max : 2Vpp, Input Current: 1mA, Max: 3mA
9. Vcc :12V
10. Input :Max : 2Vpp, Input Current: 1mA, Max: 3mA
11. Input :Max : 2Vpp, Input Current: 1mA, Max: 3mA
12. Ground
13. Output :5.5Vpp, Min : 4.5Vpp
14. Output :5.5Vpp, Min : 4.5Vpp
15. Output :5.5Vpp, Min : 4.5Vpp
16. Output :5.5Vpp, Min : 4.5Vpp
17. Output :5.5Vpp, Min : 4.5Vpp
18. Output :5.5Vpp,Min : 4.5Vpp
19. Ground
20. Input :Max : 2Vpp, Input Current : 1mA, Max : 3mA

11
11.9. VPC3230D
11.9.1. General Description
The VPC 323xD is a high-quality, single-chip video front-end, which is targeted for 4:3 and 16:9, 50/60-Hz
and 100/120 Hz TV sets. It can be combined with other members of the DIGIT3000 IC family (such as
DDP 331x) and/or it can be used with 3rd-party products.
The main features of the VPC 323xD are
• high-performance adaptive 4H comb filter Y/C separator with adjustable vertical peaking
• multi-standard colour decoder PAL/NTSC/SECAM including all substandards
• four CVBS, one S-VHS input, one CVBS output
• two RGB/YCr Cb component inputs, one Fast Blank (FB) input
• integrated high-quality A/D converters and associated clamp and AGC circuits
• multi-standard sync processing
• linear horizontal scaling (0.25 ... 4), as well as non-linear horizontal scaling ‘Panorama-vision’
• PAL+ preprocessing
• line-locked clock, data and sync, or 656-output interface
• peaking, contrast, brightness, color saturation and tint for RGB/ YC r C b and CVBS/ S-VHS
• high-quality soft mixer controlled by Fast Blank
• PIP processing for four picture sizes (1/4, 1/9, 1/16 or 1/36 of normal size) with 8-bit resolution
• 15 predefined PIP display configurations and expert mode (fully programmable)
• control interface for external field memory
• I2C-bus interface
• one 20.25-MHz crystal, few external components
• 80-pin PQFP package
11.9.2. Pin Connections and Short Descriptions
NC = not connected
LV = if not used, leave vacant
X = obligatory; connect as described in circuit diagram
SUPPLYA = 4.75...5.25 V, SUPPLYD = 3.15...3.45 V
Pin No.
PQFP
80-pin
Pin Name Type Connection
(if not used) Short Description
1B1/CB1IN IN VREF Blue1/Cb1 Analog Component Input
2G1/Y1IN IN VREF Green1/Y1 Analog Component Input
3R1/CR1IN IN VREF Read1/Cr1 Analog Component Input
4B2/CB2IN IN VREF Blue2/Cb2 Analog Component Input
5G2/Y2IN IN VREF Green2/Y2 Analog Component Input
6R2/CR2IN IN VREF Read2/Cr2 Analog Component Input
7ASGF XAnalog Shield GNDF
8FFRSTWIN IN LV or GNDDFIFO Reset Write Input
9VSUPCAP OUT XDigital Decoupling Circuitry Supply Voltage
10 VSUPD SUPPLYD XSupply Voltage, Digital Circuitry
11 GNDDSUPPLYD XGround, Digital Circuitry
12 GNDCAP OUT XDigital Decoupling Circuitry GND
13 SCL IN/OUT XI2C Bus Clock
14 SDA IN/OUT XI2C Bus Data
15 RESQ IN XReset Input, Active Low
16 TEST IN GNDDTest Pin, connect to GNDD
17 VGAV IN GNDDVGAV Input
18 YCOEQ IN GNDDY/C Output Enable Input, Active Low
19 FFIE OUT LV FIFO Input Enable
20 FFWE OUT LV FIFO Write Enable
21 FFRSTW OUT LV FIFO Reset Write/Read
22 FFRE OUT LV FIFO Read Enable
23 FFOE OUT LV FIFO Output Enable
24 CLK20 IN/OUT LV Main Clock output 20.25 MHz
25 GNDPA OUT XPad Decoupling Circuitry GND
26 VSUPPA OUT XPad Decoupling Circuitry Supply Voltage
27 LLC2 OUT LV Double Clock Output
28 LLC1 IN/OUT LV Clock Output
29 VSUPLLC SUPPLYD XSupply Voltage, LLC Circuitry

12
30 GNDLLC SUPPLYD XGround, LLC Circuitry
31 Y7 OUT GNDYPicture Bus Luma (MSB)
32 Y6 OUT GNDYPicture Bus Luma
33 Y5 OUT GNDYPicture Bus Luma
34 Y4 OUT GNDYPicture Bus Luma
35 GNDYSUPPLYD XGround, Luma Output Circuitry
36 VSUPY SUPPLYD XSupply Voltage, Luma Output Circuitry
37 Y3 OUT GNDYPicture Bus Luma
38 Y2 OUT GNDYPicture Bus Luma
39 Y1 OUT GNDYPicture Bus Luma
40 Y0 OUT GNDYPicture Bus Luma (LSB)
41 C7 OUT GNDCPicture Bus Chroma (MSB)
42 C6 OUT GNDCPicture Bus Chroma
43 C5 OUT GNDCPicture Bus Chroma
44 C4 OUT GNDCPicture Bus Chroma
45 VSUPC SUPPLYD XSupply Voltage, Chroma Output Circuitry
46 GNDCSUPPLYD XGround, Chroma Output Circuitry
47 C3 OUT GNDCPicture Bus Chroma
48 C2 OUT GNDCPicture Bus Chroma
49 C1 OUT GNDCPicture Bus Chroma
50 C0 OUT GNDCPicture Bus Chroma (LSB)
51 GNDSY SUPPLYD XGround Sync Pad Circuitry
52 VSUPSY SUPPLYD XSupply Voltage, Sync Pad Circuitry
53 INTLC OUT LV Interlace Output
54 AVO OUT LV Active Video Output
55 FSY/HC/HSYA OUT LV Front Sync/ Horizontal Clamp Pulse/Front-End
Horizontal Sync Output
56 MSY/HS IN/OUT LV Main Sync/Horizontal Sync Pulse
57 VS OUT LV Vertical Sync Pulse
58 FPDAT/VSYA IN/OUT LV Front End/Back-End Data/Front-End Vertical Sync
Output
59 VSTBYY SUPPLYA XStandby Supply Voltage
60 CLK5OUT LV CCU 5 MHz Clock Output
61 NC -LV or GNDDNot Connected
62 XTAL1 IN XAnalog Crystal Input
63 XTAL2 OUT XAnalog Crystal Output
64 ASGF XAnalog Shield GNDF
65 GNDFSUPPLYA XGround, Analog Front-End
66 VRT OUTPUT XReference Voltage Top, Analog
67 I2CSEL IN XI2C Bus Address Select
68 ISGND SUPPLYA XSignal Ground for Analog Input, connect to GNDF
69 VSUPF SUPPLYA XSupply Voltage, Analog Front-End
70 VOUT OUT LV Analog Video Output
71 CIN IN LV Chroma/Analog Video 5 Input
72 VIN1 IN VRT Video 1 Analog Input
73 VIN2 IN VRT Video 2 Analog Input
74 VIN3 IN VRT Video 3 Analog Input
75 VIN4 IN VRT Video 4 Analog Input
76 VSUPAI SUPPLYA XSupply Voltage, Analog Component Inputs Front-End
77 GNDAI SUPPLYA XGround, Analog Component Inputs Front-End
78 VREF OUTPUT XReference Voltage Top, Analog Component Inputs
Front-End
79 FB1IN IN VREF Fast Blank Input
80 AISGND SUPPLYA XSignal Ground for Analog Component Inputs, connect
to GNDAI

13
11.10. SDA55XX (SDA5550)
11.10.1. General description
The SDA55XX is a single chip teletext decoder for decoding World System Teletext data as well as Video
Programming System (VPS), Program Delivery Control (PDC), and Wide Screen Signalling (WSS) data
used for PAL plus transmissions (Line 23). The device also supports Closed caption acquisition and
decoding. The device provides an integrated general-purpose, fully 8051-compatible Microcontroller with
television specific hardware features. Microcontroller has been enhanced to provide powerful features such
as memory banking, data pointers, and additional interrupts etc. The on-chip display unit for displaying
Level 1.5 teletext data can also be used for customer defined on screen displays. Internal XRAM consists
of up to16 Kbytes. Device has an internal ROM of up to 128 KBytes. ROMless versions can access up to 1
MByte of external RAM and ROM. The SDA 55XX supports a wide range of standards including PAL,
NTSC and contains a digital slicer for VPS, WSS, PDC, TTX and Closed Caption, an accelerating
acquisition hardware module, a display generator for Level 1.5 TTX data and powerful On screen Display
capabilities based on parallel attributes, and Pixel oriented characters (DRCS).
The 8-bit Microcontroller runs at 360 ns. cycle time (min.). Controller with dedicated hardware does most of
the internal TTX acquisition processing, transfers data to/from external memory interface and receives/
transmits data via I2C-firmware user-interface. The slicer combined with dedicated hardware stores TTX
data in a VBI buffer of 1 Kilobyte. The Microcontroller firmware performs all the acquisition tasks (hamming
and parity-checks, page search and evaluation of header control bits) once per field. Additionally, the
firmware can provide high-end Teletext features like Packet-26-handling, FLOF, TOP and list-pages. The
interface to user software is optimized for minimal overhead. SDA 55XX is realized in 0.25 micron
technology with 2.5 V supply voltage and 3.3 V I/O (TTL compatible). The software and hardware
development environment (TEAM) is available to simplify and speed up the development of the software
and On Screen Display. TEAM stands for TVT Expert Application Maker. It improves the TV controller
software quality in following aspects:
–Shorter time to market
–Re-usability
–Target independent development
–Verification and validation before targeting
–General test concept
–Graphical interface design requiring minimum programming and controller know how.
–Modular and open tool chain, configurable by customer.

14
11.11. TDA9885/86
11.11.1. General description
The TDA9885 is an alignment-free single standard (without positive modulation) vision and sound IF signal PLL.
The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) vision and sound IF signal PLL
demodulator for positive and negative modulation including sound AM and FM processing.
Both devices can be used for TV, VTR, PC and set-top box applications.
11.11.2. Features
• 5 V supply voltage
• Gain controlled wide-band Vision Intermediate Frequency (VIF) amplifier (AC-coupled)
• Multistandard true synchronous demodulation with active carrier regeneration (very linear demodulation, good
intermodulation figures, reduced harmonics, excellent pulse response)
• Gated phase detector for L/L accent standard
• Fully integrated VIF Voltage Controlled Oscillator (VCO), alignment-free; frequencies switchable for all
negative and positive modulated standards via I2C-bus
• Digital acquisition help, VIF frequencies of 33.4, 33.9, 38.0, 38.9, 45.75 and 58.75 MHz
• 4 MHz reference frequency input [signal from Phase-Locked Loop (PLL) tuning system] or operating as crystal
oscillator
• VIF Automatic Gain Control (AGC) detector for gain control, operating as peak sync detector for negative
modulated signals and as a peak white detector for positive modulated signals
• Precise fully digital Automatic Frequency Control (AFC) detector with 4-bit digital-to-analog converter; AFC bits
via I2C -bus readable
• TakeOver Point (TOP) adjustable via I2C-bus or alternatively with potentiometer
• Fully integrated sound carrier trap for 4.5, 5.5, 6.0 and 6.5 MHz, controlled by FM-PLL oscillator
• Sound IF (SIF) input for single reference Quasi Split Sound (QSS) mode (PLL controlled)
• SIF AGC for gain controlled SIF amplifier; single reference QSS mixer able to operate in high performance
single reference QSS mode and in intercarrier mode, switchable via I2C-bus
• AM demodulator without extra reference circuit
• Alignment-free selective FM-PLL demodulator with high linearity and low noise
• I2C-bus control for all functions
• I2C-bus transceiver with pin programmable Module Address (MAD).
11.11.3. Pinning
SYMBOL PIN DESCRIPTION
VIF1 1VIF differential input 1
VIF2 2VIF differential input 2
OP1 3output 1 (open-collector)
FMPLL 4FM-PLL for loop filter
DEEM 5de-emphasis output for capacitor
AFD 6AF decoupling input for capacitor
DGND 7digital ground
AUD 8audio output
TOP 9tuner AGC TakeOver Point (TOP)
SDA 10 I2C-bus data input/output
SCL 11 I2C-bus clock input
SIOMA 12 sound intercarrier output and MAD select
n.c. 13 not connected
TAGC 14 tuner AGC output
REF 15 4 MHz crystal or reference input
VAGC 16 VIF-AGC for capacitor; (Not connected for TDA9885)
CVBS 17 video output
AGND 18 analog ground
VPLL 19 VIF-PLL for loop filter
VP20 supply voltage (+5 V)
AFC 21 AFC output
OP2 22 output 2 (open-collector)
SIF1 23 SIF differential input 1
SIF2 24 SIF differential input 2

15
11.12. TDA1308
11.12.1. General Description
The TDA1308 is an integrated class AB stereo headphone driver contained in an SO8 or a DIP8 plastic
package. The device is fabricated in a 1 mm CMOS process and has been primarily developed for portable
digital audio applications.
11.12.2. Features
• Wide temperature range
• No switch ON/OFF clicks
• Excellent power supply ripple rejection
• Low power consumption
• Short-circuit resistant
• High performance
• high signal-to-noise ratio
• High slew rate
• Low distortion
• Large output voltage swing.
11.12.3. Pinning
SYMBOL PIN DESCRIPTION PIN VALUE
OUTA 1Output A (Voltage swing) Min : 0.75V, Max : 4.25V
INA(neg) 2Inverting input A Vo(clip) : Min : 1400mVrms
INA(pos) 3Non-inverting input A 2.5V
VSS 4Negative supply 0V
INB(pos) 5Non-inverting input B 2.5V
INB(neg) 6Inverting input B Vo(clip) : Min : 1400mVrms
OUTB 7Output B (Voltage swing) Min : 0.75V, Max : 4.25V
VDD 8Positive supply 5V, Min : 3.0V, Max : 7.0V
11.13. AN7522N
11.13.1. General description
AN7522N is a BTL 5.0W x 2ch Power Amplifier with Standby and Volume Function Silicon Monolithic
Bipolar IC. It is used for low frequency amplifier applications.
11.13.2. Pin Descriptions
Pin No Description Pin No Description
1Vcc 7GND (Input)
2Ch.1 Output (+) 8Ch.2 Input
3GND (Ch.1 Output) 9Volume
4Ch.1 Output (-) 10 Ch.2 Output (-)
5Standby 11 GND (Ch.2 Output)
6Ch.1 Input 12 Ch.2 Output (+)

16
11.14. PI5V330
11.14.1. General description
Pericom Semiconductor’s PI5V series of mixed signal video circuits are produced in the Company’s
advanced CMOS low-power technology, achieving industry leading performance.
The PI5V330 is a true bidirectional Quad 2-channel multiplexer/demultiplexer that is recommended for both
RGB and composite video switching applications. The VideoSwitch™ can be driven from a current output
RAMDAC or voltage output composite video source.
Low ON-resistance and wide bandwidth make it ideal for video and other applications. Also this device has
exceptionally high current capability which is far greater than most
analog switches offered today. A single 5V supply is all that is required for operation.
The PI5V330 offers a high-performance, low-cost solution to switch between video sources. The
application section describes the PI5V330 replacing the HC4053 multiplier and buffer/amplifier.
11.14.2. Features
• High-performance, low-cost solution to switch between video sources
• Wide bandwidth: 200 MHz
• Low ON-resistance: 3W
• Low crosstalk at 10 MHz: –58 dB
• Ultra-low quiescent power (0.1 µA typical)
• Single supply operation: +5.0V
• Fast switching: 10 ns
• High-current output: 100 mA
• Packages available:
–16-pin 300-mil wide plastic SOIC (S)
–16-pin 150-mil wide plastic SOIC (W)
–16-pin 150-mil wide plastic QSOP (Q)
11.14.3. Pin Descriptions
Pin Name Description
S1A, S2A
S1B, S2B
S1C, S2C
S1D, S2D
Analog Video I/O
IN Select Input
EN Enable
DA, DB,
DC, DDAnalog Video I/O
GND Ground
VCC Power

17
11.15. GM6015
11.15.1. General description
The Genesis Microchip 6015RD1 LCD TV reference board is a complete display processor for LCD, PDP
and LCOS based televisions. The reference board demonstrates the processing capabilities of the Genesis
Microchip gm6015 television controller IC. The gm6015 IC is a full-featured, dual-channel video processor
with Genesis industry leading Crystal Ciema PlusTM video scan conversion. The 6015RD1 board inputs
analog YPbPr/RGB, NTSC/PAL/SECAM CVBS/YC, UHF/VHF and outputs digital RGB to an XGA LCD
panel. A convenient on-screen display system provides easy control of the board’s processing capabilities.
The design kit is complete with hardware and software. Software includes G-Probe debug software, G-
Wizard register calculator and G-TV application source code.
The 6015RD1 is a related reference board that outputs analog YpbPr/RGB.
11.15.2. Features
• Dual channel, gm6015 based LCD TV system
• Industry leading Crystal Cinema Plus video scan conversion
• Inputs:
i. Component analog YPbPr/RGB
ii. 480/576I, 480/576P, 720P and 1080I HD
iii. Dual NTSC/PAL/SECAM CVBS and YC
iv. VGA, SVGA, XGA PC graphics
v. Separate, composite or sync on Y/G
vi. UHF/VHF RF (NTSC)
• Default output with XGA LCD interface PCB:
i. Component analog YpbPr/RGB
• Other outputs:
ii. 8/16/20/24-bit 4:2:2/4:4:4 digital YCbCr/RGB
iii. 480/576I, 480/576P, 720P and 1080I HD
iv. VGA, SVGA, XGA PC graphics
v. Separate, composite or sync on Y/G
• On-screen display (OSD) user interface with automated self running demonstration
• Small form factor PCB